Problem 1 The box shown is supported by rollers at A and E, a ball and socket connection at D, and cable BC. Determine the support reactions if a = 83.6206°, ẞ = 116.3878°, and y = 152.734°. The roller at A only resists force in the y direction and the roller at E only resists force in the z direction. Z-axis /x-axis 4001% y-axis

Problem 1 The box shown is supported by rollers at A and E, a ball and socket connection at D, and cable BC. Determine the support reactions if a = 83.6206°, ẞ = 116.3878°, and y = 152.734°. The roller at A only resists force in the y direction and the roller at E only resists force in the z direction. Z-axis /x-axis 4001% y-axis

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.39P: The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables...

See similar textbooks

Similar questions

A 4807 lb forklift used by Multi-National United is holding a 213 lb wooden block. Let z = 12in, y = 35in and z = 49in. 213 lbs 4807 bs A 12 in 35 in 49 in +x+y Determine the reaction at the front and rear wheels. To find the reaction at the front wheel, we'll use the moment on the (front/rear) wheel. The reaction on the front wheel is Ibs. To find the reaction at the rear wheel, we'll use the moment on the (front/rear) wheel. The reaction on the rear wheel is Ibs.
Situation 22 - For the frame shown in AN- 5 m 15, the force F acting upward at C causes a RA horizontal reaction of 100 N at B. 29. Determine the value of the force F in kN. Answer: 120 kN 30. Determine the reaction at A in kN. Answer: 156.2 kN 31. Determine the angle in degrees that the reaction at A makes with the horizontal Figure SP-3.25 axis (positive counter clockwise). Answer: 230.19°
The radius of pulleys C and B are 125mm and 250mm,respectively. Given that TB=T'B=90kN and TC=T'C=150kN, find the reactions of supports A and D.
A The reaction in the x-direction at joint A in Figure is: O-5.774 KN 5.774 KN O 5.0 kN 5 KN OOKN E 30" 30" F 10 kN D B ALL DIMENSIONS IN METRES (0.5774) (0.5774)
Given the Horizontal wood member shown that weights 38 lbs/ft and supports three vertical loads F1 - 200 Lbs, F2= 100 Lbs, F3 = -400 Lbs, and is supported by a Pin at A and a Roller at B, calculate Reaction Ay. A origin k 4' 200# f 4' 100# + 400# 4' t 4' B X
The member is supported by a square rod which fits loosely through the smooth square hole of the attached collar at A and by a roller at B. The member is subjected to the forces Fi = 300 N, F2 = 450 N, and F3 = 600 N. (Figure 1) Determine the components of the reaction force of the support at A using scalar notation. Express your answers using three significant figures separated by comma. Ar, Ay = -300,-450 N Submit Previous Answers v Correct Part C Determine the components of moment of the reaction at A using scalar notation. Figure 1 of 1 Express your answers using three significant figures separated by commas. vec (MA)=: (MA)y, (MA): =- 900,100, – 1350 N.m B 1 m 2 m Submit Previous Answers Request Answer 2 m X Incorrect; Try Again; 4 attempts remaining < Return to Assignment Provide Feedback 圓
The figure below depicts the tire, axle, and gear of a large tractor. The entire structure is in mechanical equilibrium. Bearings support the rotating axle at points A and C attached to the tractor's frame. A force FD = 5000 lb is applied in the -z direction at point G of a gear with a 3-in radius. The force W = 1000 lb in the +z direction represents a normal force resulting from the weight of the tractor. The force Q acting in the +x direction, represents the traction force between the tire and the ground. The wheel, axle, and gear assembly weigh 150 lb with center of gravity at point D, which lies on the y axis with coordinate yp = -18 in. Points A, C, D (not seen in the figure), and E lie in the yz plane. Point G lies in the xy plane. Questions & Analysis: (a) Draw the FBD for the wheel, axle, and gear assembly if the bearings at A and B resist moments and the bearing at A is a thrust bearing. Label all unknowns. (b) Is the assembly statically determinate or statically…
perpendicular to the page through the point o. (Let counterclockwise torque be positive and let forces to the right and up be positive. Use the following as necessary: the forces R, Write the necessary equations of equilibrium of the object shown in the figure below. Take the origin of the torque equation about an axis RFF, and F the length l of the object; and the angle e that the object makes with the horizontal.) EF, = = 0 Fy =0 Στ. =0 Need Help? Read It
X Problem 4 The rod, supported by thrust bearing at A and cable BC, is subjected to an 80 lb force. Draw a FBD suitable to find the reactions at A and B. Z A 6 ft F = 80 lb 1.5 ft C B 1.5 ft
4.Three members of a frame on a knot plate can be seen in the picture below. Determine the size and direction of the Result of Style on the knot plate analytically and graphically F1 Pelat Buhul F2 F3 F1 = 15 N F2 = 13 N F3 = 10 N Teta = 30 ^o
Cansider the pipe shown in (Figure 1). The forces F = 250 N. F = 400 N and F = 600 N are paralel to the , y and z axes, respectively Part A Determine the z y and z components of reaction at the fixed support A using scalar notation Express your answers using three significant figures separated by commas VAE t vec Az. Ay. Az= Submit Request Answer Part B Determine the z, y and z components of moment of reaction at the foxed support A using scalar notation. Express your answers using three significant figures separated by commas. VAE vec (MA). (MA)y. (M,); = N.m Figure Submit Request Answer Provide Feedback 1 m 0.75 m 0.75 m
Find the reactions at D and B ..Take F1=200 N,F2=175 N, F3=150N, M=28 N.m, * F1 F2 45 85mm +75 mm- M F3 B D 125 N -100 mm- 150 mm 50 mm 1 Add file