Answered: Problem 1. Determine the slope and…

Engineering

Civil Engineering

Problem 1. Determine the slope and deflection at B and C. Also, determine the maximum deflection.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.28P

See similar textbooks

Related questions

Q: Question 2 The maximum speed of a vehicle on a 4º curve having arc length 30 m is limited to 60…

A: Given- Degree of curve D = 4o Arc length L=30 m, Velocity V=60 kmph, It is needed to find the value…

Q: 15 kN 3.75 kN/m - 2.4 m CH 0.6 m 6kN/m -0.9m 75 IN A

Q: A wall of diameter 20 cm fully penetrates a confined aquifer After a Long period of pumping at a…

Q: Q- Calculate the corrected staff reading at point A, if the staff reading is taken from an instrumen…

A: Given: The staff reading is taken from an instrument which is set at, A distance, d = 1.5 km. From…

Q: Compute the flexural strength of a singly reinforced beam, 200 mm in width and 400 mm in total…

A: Answer (a) As = 2-16 mm Calculation of flexural strength of a singly reinforced beam We know that…

Q: In Case Study 3-2, Virgilio v. City of New York and Motorola, the court dismissed the lawsuit by New…

A: Performance Requirements: 1. The radios need to be able to receive and send signals in any…

Q: The main beam of UB 610 x 229 x 101 kg/m in steel grade S275 supportssecondary beamsof UB 406 x 140…

A: Given: Slab dimensions: Longer span = 5015 mm Shorter span = 1715 mm UDL = 400 kg/m2

Q: The system in Fig 2 pumps water from a lower reservoir to a higher reservoir. The pipe diameter is…

A: Given data- Pipe diameter D = 0.235 m, Pipe lengths L1= 5 m, L2= 4.5 m, L3= 1.5 m, and L4= 0.6 m.…

Q: Draw a simple Structure/Building then label its components.

A: All buildings are primarily divided into three parts as given below: Foundation: This is the lowest…

Q: Determine the maximum force, P, that can be supported by the truss shown given that the capacity of…

A: To determine the maximum value of P such that force in tension members does not exceed 8kN and force…

Q: = A rectangular foundation of size (L = 3 m, w =2 m) at a depth (D, =1.5 m) is subjected to vertical…

A: Given data, Length of foundation (L) = 3m Width of foundation (w) = 2m Vertical pressure on…

Q: Consider a beam supported by a pin and at A and roller at B subjected to uniform distributed load w…

Q: The thickness of the boundary layer for a fluid flowing over a flat plate at a point 20 cm from the…

A: Given: Thickness of boundary layer, δ=4 mm Distance from the leading edge, x = 20 cm = 200 mm…

Q: What are the M’s of construction management? Explain each.

Q: estion about Sanitary Engineering Question: A Water supply scheme has to be designed for a city…

A: The major types of drafts that may be required to be recorded for an average water consumption of…

Q: b) A level run was carried out, using the data below compute the difference in level between points…

A: Given Reduced level of datum = 50 m

Q: Question: In Marshall method of mix design the coarse aggregate, fine aggregate, filler and bitumen…

A: Given: In Marshall method of mix design the coarse aggregate, fine aggregate, filler and bitumen…

Q: The beam shown in Figure 3 has an inclination of 30° from the horizontal axis and it is pinned at A…

A: A beam is inclined 30deg with horizontal and a load,P vertical to the beam is applied at 2 m from A…

Q: Q- Calculate the corrected staff reading at point A, if the staff reading is taken from an…

Q: Find the length of cantilever beam to carry the loads shown in the figure below: D.L= Self weight,…

A: Section is uncracked, To determine the length, L of the cantilever beam. Taking unit weight of…

Q: make me a sketch of a floor plan sized 21.5meters x 14 meters with porch, carport, living area,…

A: To draw a Floor Plan in an area of 21.5 m x 14 m To provideporchcarportliving areadining…

Q: At a well the ground elevation is 1510.0 (m asl), the depth to the water is 5.0 (m) and the…

A: The following is the given information, The ground elevation is 1510.0 (m asl). The depth to the…

Q: b) ↓↓ Y 2.8.2 Solve per for a circular arch whose footings slide radially but cannot rotate (Fig.…

A: The given figure is shown below:

Q: Design the reinforcement of the section shown. For concrete, fc' = 21 MPa and for steel, fy = 275…

Q: The length of a summit curve is 188 meters. Compute the radius of the curve if the tangent grades…

A: Given data, Length of summit curve= 188 metres Tangent grades are +3% and -5% . Radius of the…

Q: 1. A soil has a Cu =1, then it is considered as a poorly graded soll. 2. A soil has L.L-60% and…

A: As per our company guidelines we are supposed to answer only 3 question kindly repost other question…

Q: During a storm event in a certain period, the rainfall intensity is 6.5 cm/hour and the - index is…

A: Given that :- Rainfall intensity = 6.5 cm/hour ϕ-index = 4.5 cm/hour To find the intensity of…

Q: Solve the following problems completely using Double Integration Method, Area moment method and…

A: Given To find RA , RB ,and MA by Double Integration Method, Area moment method and Conjugate beam…

Q: THEORY OF STRUCTURES Use the substitute member to make a complete analysis of the complex truss…

A: Solution: Compute the support reactions ΣFx=0-ax+30=0ax=30…

Q: A 4 m thick layer of normally consolidated clay has an average void ratio of 1.30. Its compression…

A: Given data- Normally consolidated clay layer- Height H=4 m, Void ratio e=1.30, Compression index…

Q: For the bi-supported bar of the Figure, draw the bending moment (M) and bending force (V) diagrams,…

A: Given Data Find the shear and moment equation of beam and draw shear force (V) and bending moment…

Q: Classify the structures in following figures. Indicate if stable or unstable. If unstable, indicate…

A: Given Data Classify the structure whether it is stable or unstable and determinate or…

Q: The soil profile at a building site consists of dense sand up to 2 m depth, normally loaded soft…

A: Given Data Find the ultimate settlement resulting from a uniformly distributed surface load of 40…

Q: Problem 2. Determine the maximum deflection and slope.

A: Given Data a = 4 and b = 2 Find the maximum slope and maximum deflection in beam using Area-moment…

Q: A GRADE OF -5% IS FOLLOWED BY A GRADE OF + 1%, THE GRADES INTERSECTING AT STATION 10 +050 OF…

Q: Based on the layout of the water supply system, how much pressure in psi will be available at the…

Q: V. vi. vii. Soils are derived from the weathering of rocks and are commonly described by terms such…

A: The majority of land is covered with loose surface material called soil. It is made up of both…

Q: Given: H 8kips K TIT 1- 201 R₁ RIGID } K₂ R₂ K₁ = K₂=K3 = 1 = 1 20' KIP/in Find: R₁, R₂, Rg ↑ R3

Q: A W610 x 82 beam of A 36 steel has end reaction of 302 kN and is supported on a plate with a length…

A: Answer In order to check the beam adequacy for web crippling let us first find the Nominal web…

Q: 6. a) Welding has two main categories, discuss them in details b. Define and Distinguish these terms…

A: a) Welding has two main categories: Fusion Welding Solid state welding Fusion welding: It is the…

Q: Question 1 In a Lacey's Regime channel, the discharge is 100m³/s and the longitudinal slope is…

A: Given: A Lacey's regime channel, Discharge, Q=100 m3s The longitudinal slope, S = 0.0002 Slit…

Q: Draw the shear force and bending moment diagram of the beam assuming A is pinned, and B and C are…

A: Given Data E = 29,000 ksi Draw shear force and bending moment diagram. Let's solve using Moment…

Q: Question An engineer has designed a road with a curve of radius 12 m. The material of the road…

A: Given- Radius of curve R=12 m, coefficient of friction =0.3, It is needed to find the maximum…

Q: For the cantilevered beam in the Figure, draw the Bending Moment (M) and Shear Force (V) diagrams,…

A: Given data in question Point load 20 kN Span 4 m Cantilever beam To find out SFD BMD

Q: Ques What is the kinematic indeterminacy for the frame shown below (member inextensible) Hinge…

A: Given- A frame is given- Members of the frame are in-extensible. It is needed to find the kinematic…

Q: The laboratory tests on a soil sample gave the following results: 1). Natural water content, W₁ =…

Q: Situation 3. Figure 1-3 The roof is supported by cables as shown. If the cables exert forces FAB =…

A: Given Data Find the resultant force acting at A in Cartesian vector form.

Q: Homework: if the water content of a certain saturated soil is 22% and the specific gravity is 2.65%…

Q: 2 m ………………………………… Circular arc 4 m a. 789.77 www a. 243.42 4 m 4 m 2 m Situation 6: A thin metal…

A: To find the centroid and Moment of Inertia of the area given

Q: It is a form of subsurface presentation that depicts the position and thickness of various strata.

A: Geological subsurface maps- Geological subsurface maps means the map which find out the geological…

Question

ASAP

a=4

b=2

INSTRUCTION: Solve the following problems. Show your solutions. If the answer is not exact,
round it to the nearest 2 decimal places.
PART 1. Answer the following using Double Integration Method. Establish all the slope and deflection
equation
Problem 1. Determine the slope and deflection at B and C. Also, determine the maximum deflection.
[15+ 4b] KN
[24 +2a] kN/m
Anmum
1m
B
1 m
C
4 m
second largest nonzero digit in your student number
b = second smallest nonzero digit in your student number
D
Problem 2. Determine the slope and deflection at B. Also, determine the maximum deflection and slope.
16 + 2cl KN
[12+ 3d] kN/m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step by step

Solved in 8 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Kindly solve the slope and deflection at each point using Area Moment Method (show solutions and diagrams) some answers: θC = 0.335°ΔB = 8 mm ΔC = 30.22 mm
1. Determine the equations of slope and deflection. 2. Determine the slope and deflection at point 3m from point A. E =210 GPa. 100 | Cross section 6KN.m 2m B8KN 2 kN/m 2m T ) B8KN 2m
Kindly solve the slope and deflection at each point using Area Moment Method (show solutions and diagrams) some answers:θC = 0.465°ΔC = 40.52 mm
solve using double integration method.Compute the vertical deflection of point C for the beam shown below. Given that? = 1200 ??.4and ? = 29000 ?/??.2
By obtaining the slope and deflection equations, evaluate the variation of slope and deflection along asimply supported beam and plot the solution along the beam ? − ????. Using the principle of superposition find the deflection and slope values point D
Please solve this problem using the slope deflection method and show all steps please
Slope deflection method: compute for shear and momemt diagram
For the beam shown below, determine the value of maximum deflection and maximum slope if ? = 29000 ??? ??? ? = 25 ??⁴. Use conjugate beam method.
Use Area moment method Determine the ff. 1.Maximum deflection 2.slope at point a and b 3.Maximum deflection
ANYONE CAN HELP! Using the conjugate-beam method, determine the slope and the deflectionat at points B andD for the beam shown below, E = 200 GPa
2. Calculate the slope at C using ONE of these methods: double integration method, area-moment and conjugate beam method. Also, determine the deflection at C using EITHER virtual work method or Castigliano theorem method. Set P = 17 kN, w = 22 kN/m, support A is pin and support B is roller.
Using Area-Moment Method, determine the following: a. slope at point B b. deflection at point B c. moment reaction at fixed support A d. vertical reaction at fixed support A