Problem #1. The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel with the following properties: Elastic Modulus, E = 200 GPa and Shear Modulus, G = 75 GPa. - Determine the following: (a) Absolute maximum torsional shear stress (b) Angle of twist of the end B with respect to the support Show complete solution (FBDs and equilibrium equations). A 200 mm CL B TB N-m D 20 N-m 30 N-m 800 mm 600 mm

Problem #1. The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel with the following properties: Elastic Modulus, E = 200 GPa and Shear Modulus, G = 75 GPa. - Determine the following: (a) Absolute maximum torsional shear stress (b) Angle of twist of the end B with respect to the support Show complete solution (FBDs and equilibrium equations). A 200 mm CL B TB N-m D 20 N-m 30 N-m 800 mm 600 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC≤ 4.6°. Assume L1=0.6 m and L2=1.0 m. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in N-m rounded to three significant digits.
An shaft consist of a hollow shaft 3m long, with an outside diameter of 200mm and an inside diameter of 150mm, rigidly attached to a solid shaft 2m long with a diameter of 150mm. Determine the maximum torque which can be applied without exceeding a shearing stress of 70 MPA or a twist of 4.3° in the 5m length. Use G=83 GPA.
The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the torques 2T and 3T at points A and B, respectively. If tallow = 35 MPa and (fA/C)allow =2o, determine the maximum permissible value of the torque T. Use the table given below and your student ID to find the values of L1, L2, and D. L1 = 1.45 , l2 =0.95 d =86
A hollow steel shaft 2510 mm long must transmit torque of 34 KN-m. the total angle of twist must not exceed 3 degrees. The maximum shearing stress must not exceed 110 Mpa. Use G= 83 GPA. Calculate the minimum required polar moment of Inertia. 10. Calculate the minimum outside diameter so that the allowable shearing stress will not be exceeded. 11. Calculate the maximum required inside diamete
The 50-lb block and weight (W) is positioned as shown in the figure. The coefficient of static friction between the block and the plane is 0.2 and between the rope and the drum is 0.3. (a) Det. The minimum value of weight (W) which may be applied without causing the 50-lb block to slip.
A solid 1.500-in.-diameter steel [G = 12,000 ksi] shaft is subjected to torques TB = 270 lb-ft and TD= 95 lb-ft, acting in the directions shown. Assume a = 54 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 12 ksi, determine the maximum torque TC that can be applied to the shaft.
The shaft is made of two segments. AC has a diameter of 0.5in, and CB has a diameter of 1in. It is fixed at its ends A and B and is subjected to a torque T=500lb*ft. Gsteel= 10.8*103 ksi What is the minimum shear stress in the shaft?
The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 7 mm. If the normal stress in rod (1) must not exceed 215 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? What is the allowable force in road (1)? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm.
The stepped shaft ACB shown in Figure bellow is fixed at both ends and loaded by a torque TO at point C. Segment AC having solid circular cross section and segment CB having hollow circular cross section. If the shafts material is steel with shear modulus G = 11 x 10°psi, and the torque is To = 8,000 lb-in. Calculate: (a) The maximum and the minimum shear stress in segment CB. (b) The maximum and the minimum shear strain in segment CB. (c) The angle of rotation 0, at the cross section where the torque To is applied.
A solid stainless steel [G = 12,500 ksi] shaft that is 30 in. long will be subjected to a pure torque of T = 280 Ib-in. Determine the minimum diameter D required if the shear stress must not exceed 8,000 psi and the angle of twist must not exceed 0.050 rad.
The turbine motor moving at 378 rev/ min can produce 2.5 hp. The shaft diameter is 1.25 inches. Calculate the torque and shearing stress developed in the shaft.
The engine of the helicopter is delivering 600 hp to the rotor shaft AB when the blade is rotating at 1200 rev/min. Determine the diameter mm of theshaft AB if the allowable shear stress is 75 MPa and the vibrations limit the angle of twist of the shaft to 0.05 rad. The shaft is 2 ft long.