Problem 1. The beam cross sections shown (A and B) have #3 stirrups spaced at 8 inches on center. The concrete is normal weight concrete with specified compressive strength of 3,500 psi. The stirrups are made of steel having a yield value of 60,000 psi. Determine the design shear strength of the d = 25.5" h= 20" d = 17.5" h = 28" cross-sections. b= 14" b = 24" Cross section A Cross section B

Problem 1. The beam cross sections shown (A and B) have #3 stirrups spaced at 8 inches on center. The concrete is normal weight concrete with specified compressive strength of 3,500 psi. The stirrups are made of steel having a yield value of 60,000 psi. Determine the design shear strength of the d = 25.5" h= 20" d = 17.5" h = 28" cross-sections. b= 14" b = 24" Cross section A Cross section B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The design engineer specifies a concrete strength of 5500 psi. Determine the required average compressive strength for a. a new plant where s is unknown b. a plant where s 7.1 500 psi for 22 test results Questions and Problems 309 c. a plant with extensive history of producing concrete with s = d. a plant with extensive history of producing concrete with s 400 psi 600 psi
Figure 2 shows a simply supported beam and the cross section at midspan. The beam supports a uniform service (unfactored) dead load consisting of its own weight plus 1.4 kips/ft and a uniform service (unfactored) live load of 1.5 kips/ft. The concrete strength is 3500 psi, and the yield strength of the reinforcement is 60,000 psi. The concrete is normal-weight concrete. Use load (Table 5.3.1) and strength reduction factors from AC1318-14. For the midspan section shown in Fig. P4-1b, compute Mn and show that it exceeds Mu. @ (b) 3 No. 9 bars WD = 1.4 kips/ft plus weight of beam 1.5 kips/ft WL H 12 in. 20 ft TT 21.5 in. 24 in. + Figure 2.
Determine the values of the distance cfrom the extreme concrete corppression fibers to the neutral axis, andr, for the beam shown in the following Figure fy 60,000 psi and fc 3000 psi. 0.003 21 in d-c 389 bars 3.00 in) = (0.003) 12 in Select one: a. 6.90 in, 0.0061 b. 6.25 in, 0.0069 c. 7.50 in, 0.0085 d.5.93 in, 0.0076
A cantilever beam shown supports auniform service (unfactored) dead load of 1 kip/ft plus its own dead load and a concentrated service(unfactored) live load of 12 kips, as shown. The concrete is normal-weight concrete with f'c= psi and the steel is Grade 60. Use load and strength-reduction factors from ACI CodeSections 9.2 and 9.3. For the end section shown in Fig. P4-2b, compute and show that it exceeds Mu. From James Wight -Reinforced Concrete
Given the concrete (f c=6000 psi) I-beam shown in Figure 1 for the given loading: -draw the shear & moment diagrams -determine Vmax & Mmax -using ASD (Allowable Stress Design) method, check to see if the given loading produces stresses within the given allowable range (check both Omax & Vmax) Using ACI 318-99, allowable stresses are -for flexure, f = .45f'c -for shear, v. = 1.1√f. (HINTS: 8² -note that the beam is symmetric about both axes -Ix for a triangle is (1/36)bh³+Ad² ) 30 kips 16' 10 kip/ft 22' 20 kips 3'-4' -1-6 -1'-6" Figure 1 1'-
Load = 3000 lb Q:Find Stresses at: Section A-B & Section D-C "18.0"- "5,5" Plain Concrete: D Compressive Strength : 280 (Psi) "12.0"- "0.5"-
Referenced concrete When designing the same bim Why is the load in the case of moment greater than the load in the case of shear?
What is the shear force to be carried by the reinforcements of a beam subjected to axial tension if it has a width of 313 mm and an over-all depth of 477 mm? The specified compressive lightweight concrete is 22.2 MPa and the yield strength of stirrups is 333 MPa. The distance of tension reinforcements from the outer fiber of the beam is 59 mm. Round off your final answer in 3 decimal places. Loadings: VDL = 72 kN %3D VLL = 62 kN Axial Tension (DL) = 90 kN Axial Tension (LL) = 19 kN
The loadsshown on the beam with a cross section at midspan as shown, are service (unfactored)loads. The concrete used is a normal weight concrete with compressive strength of 4000 psi.The yield strength of the reinforcement is 60,000psi. For the midspan section shown, computeφMn and show that it exceeds Mu
Details of a rectangular column are as follows: Column width along the x-axis = 250 mm Column width along the y-axis = 600 mm Reinforcement 8 of 25 mm diameter bars distributed equally along the longer sudes 10 mm diameter ties spced 100 mm on centers. Concrete 28th dat compressive strength, fc' = 20.7 MPa Reinforced steel yield strength, fy = 415 MPa Assume that the compression steel yields. Concrete cover to the centroid of bars 70 mm Determine the nominal balanced load with eccentricity measure from the y-axis if the depth of the rectangular concrete compressive stress block is 90.66 mm.
Given a beam section b angle D = 450mm * 950mm M*=1500kNm, f_{c}' = 32MPa f_{5y} = 500MPa and the maximum aggregate size=20mm. Design and detail the section. Use N28 bars for the main reinforcement and R10 bars for stirrups. Exposure classifi-cation A2 applies. Please don't hand writing
Determine the nominal flexural strength for the following section if: Specified Compressive Strength of Concrete is 4000 psi. Specified yield strength for the reinforcement is 60000 psi. /- -10 in.- -14 in. 4 in. 8 in. 4 #8 7 in. 3 in. -24 in.-