Problem 2-4. For the following section, constructed of steel, determine: a) Moment at first yield (yielding moment): b) Moment when the top and bottom 25 mm of the section are yielded; c) Fully plastic moment (plastic moment); d) Shape factor. Given: E = 200 GPa, Yield stress = 300 MPa K25 mm+25 mm+ 25 mm+ *25 mm- 50 mm² K 25 mm-

Problem 2-4. For the following section, constructed of steel, determine: a) Moment at first yield (yielding moment): b) Moment when the top and bottom 25 mm of the section are yielded; c) Fully plastic moment (plastic moment); d) Shape factor. Given: E = 200 GPa, Yield stress = 300 MPa K25 mm+25 mm+ 25 mm+ *25 mm- 50 mm² K 25 mm-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following steel circular bar (Es = 200 GPa) is divided into two segments. Segment 1 is tubular and segment 2 is solid. Determine the distance "x" so that the bar does not exceed a total deformation of 2.5 mm. The load P is equal to 25 kN, the diameter d is equal to 30 mm, and the length L is equal to 10 m.
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)
Calculate the axial deformation of the Brass cylinder section (BC) shown in Figure 8. The cross-sectional areas are Asteel = 80 x 10-³ m² and ABrass = 50 x 10-³ m², and Young's modulus - of steel and brass are 200 MPa and 120 MPa. 100 kN (a) 3.13 mm (b) 7.25 mm (c) 7.5 mm (d) 3.5 mm Steel 50 kN 0.5 m B Brass 0.3 m C Figure 8. A shaft of different diameters Steel 0.5 m Ꭰ 150 kN
A 76 mm x 76 mm x 6 mm angular section is welded to a gusset plate having a thickness of 10 mm as shown in the figure. The length L1 equals 125 mm and L2 is 65 mm. The angular section has a cross sectional area of 929 mm2, Fy = 248 MPa, FU = 400 MPa. a. Determine the value of the tensile force P based on gross area in kN. b. Determine the value of tensile force P (KN) based on net area if the value of shear lag factor is 0.85. c. Determine the value of tensile force P based on block shear in gusset plate along the weld in kN. gusset plate L₂= 65 mm 25 m Allowable stresses: Allowable tensile stress (gross area) = 0.6Fy Allowable tensile stress (net area) = 0.50Fu Allowable shear stress (net area) = 0.30Fu P
The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa, Ebr 100 GPa. Figure P P -10 mm -20 mm 1 of 1 Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the steel. Express your answer to three significant figures and include appropriate units. Ost = Submit Part B Obr = Submit 0 Value If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the bronze. Express your answer to three significant figures and include appropriate units. Provide Feedback A Request Answer Value Units Request Answer Units ?
A steel bar has three segments with 600 mm long which is subjected to the differentloads as shown in Figure Q1(b). Take E=205 GPa. (i) Determine stress in each section. (ii) Calculate the total elongation (extension) in the bar.(iii) Determine the length of the middle segment (BC) to have zero elongation ofbar.(iv) Determine the diameter of the segment CD to have zero elongation of the bar.
P = 8kN. Using N = 3, determine the allowable stress for A501 grade steel. Calculate the dimensions (to 1 decimal place) of a square rod. L = 5.9m. Calculate the deformation (6) and the strain (€).
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
1. The bar ABCD consists of 3 cylindrical steel segments with different lengths and cross-sectional areas. Axial loads are applied as shown. Calculate the normal stress in each segment in psi unit. Indicate if T or C.Calculate the total axial deformation in Problem #1 if Es = 29 x 10 6 psi . Indicate if the bar elongates or contracts.
Portions of a x-in. square bar have been bent to form the two machine components shown. Knowing that the allowable stress is 18 ksi, determine the maximum load that can be applied to each component. (a) 1 in. (b) The maximum load that can be applied to component (a) is The maximum load that can be applied to component (b) is lb. lb.
The cross-sectional area of an aluminum bar is 170 mm?. It carries an axial loads at the positions as shown in the figure. Compute the total deformation of the bar if E = 80 Gpa. Assume the bar is suitably braced to prevent buckling. Add "9" in the loads only. Example: 40+9=49, 18+9=27, 42+9=51, 20+9=29 Area = 170mm' 2 40KN 18KN 20KN 42KN 1.0m 1.80m 0.70m
SITUATION I. For Items 3-5. Refer to figure 1. Axial loads are applied at rod FIGURE 1 a composed of bronze rigidly attached together. If P = 3000 lb and the cross-sectional steel, aluminum, and 4P Steel Bronze area of the rod is 0.5 in?, in the Aluminum 3. Determine the stress bronze. 2 ft a. 6000 psi b. 12000 psi c. 18000 psi d. 24000 psi 3 ft 2.5 ft е. none of the above