Please answer with complete details. Thank you. Problem #2A W 300 x 97 kg/m beam has a simple span of6 m. It carries a uniformly distributed deadload including its own weight of 15 kN/m. Thebeam has full lateral bracing. Use LRFDanalysisProp. of W 300 mm x 97d = 307.85 mmbf = 304.80 mmt = 15.37 mmtw = 9.91 mm.U = 1.2 DL + 1.6 LLSx = 1440 x 103 mm3Zx = 1586 x 103 mm³Fy = 345 MPaE = 200000 MPa.%3D%3D%3DO Determine the safe service live loadthat the beam could support based onits flexural capacity. ø = 0.902 Determine the safe service live loadthat the beam could support based onits shear capacity. ø = 0.90® Determine the safe live concentratedload at its midspan that the beam couldsupport based on its live load allowabledeflection of 1/360 of span. Flexuralrigidity El = 44000 KN.m²

Answered: Image /qna-images/answer/66281b09-e2c5-4ede-a897-a4215752542d.jpg

Problem #2 A W 300 x 97 kg/m beam has a simple span of 6 m. It carries a uniformly distributed dead load including its own weight of 15 kN/m. The beam has full lateral bracing. Use LRFD analysis Prop. of W 300 mm x 97 d = 307.85 mm bf = 304.80 mm t = 15.37 mm tw = 9.91 mm. U = 1.2 DL + 1.6 LL Sx = 1440 x 103 mm3 Zx = 1586 x 103 mm³ Fy = 345 MPa E = 200000 MPa. %3D %3D O Determine the safe service live load that the beam could support based on its flexural capacity. ø = 0.90 O Determine the safe service live load that the beam could support based on its shear capacity. ø = 0.90 ® Determine the safe live concentrated load at its midspan that the beam could support based on its live load allowable deflection of 1/360 of span. Flexural rigidity El = 44000 KN.m²

Problem #2 A W 300 x 97 kg/m beam has a simple span of 6 m. It carries a uniformly distributed dead load including its own weight of 15 kN/m. The beam has full lateral bracing. Use LRFD analysis Prop. of W 300 mm x 97 d = 307.85 mm bf = 304.80 mm t = 15.37 mm tw = 9.91 mm. U = 1.2 DL + 1.6 LL Sx = 1440 x 103 mm3 Zx = 1586 x 103 mm³ Fy = 345 MPa E = 200000 MPa. %3D %3D O Determine the safe service live load that the beam could support based on its flexural capacity. ø = 0.90 O Determine the safe service live load that the beam could support based on its shear capacity. ø = 0.90 ® Determine the safe live concentrated load at its midspan that the beam could support based on its live load allowable deflection of 1/360 of span. Flexural rigidity El = 44000 KN.m²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A T-beam for a floor system has a slab thickness of 75 mm and a web thickness of 375 mm. It has an effective depth of 600 mm. The beam carries a dead load moment of 280 kN-m and a live load moment of 525 kN-m. It has a span of 5.4 m and a spacing center to center of 1.8 m. Use reduction factor ø=0.90, fc’=20.7 MPa, fy = 344.7 MPa.Determine the effective width of flange. Determine depth of compression flange. Determine the required steel area. See the formula in the image
A T-beam for a floor system has a slab thickness of 75 mm and a web thickness of 375 mm. It has an effective depth of 600 mm. The beam carries a dead load moment of 280 kN-m and a live load moment of 525 kN-m. It has a span of 5.4 m and a spacing center to center of 1.8 m. Use reduction factor ø=0.90, fc’=20.7 MPa, fy = 344.7 MPa. Determine the effective width of flange. Determine depth of compression flange. Determine the required steel area. See the formula in the instructions
(a). A beam 6 m long is fixed at both ends. It carries DL = 14 Kn/m and LL = 20 kN/m. If EG = 28 MPa, fy = 420 MPa, and wt of conc = 23.5 kN/m?, design a singly reinforced rectangular beam using NSCP 2015. Use 20mm diameter bars. (b). Determine the required spacing of 10mm diameter stirrups at the critical section.
A reinforced concrete beam, b by h with tensile reinforcement of 6-25mm diameter bars is simply supported on a clear span of 12m. Given: fc = 12 MPa fs = 140 Mpa wc = 24 kN/m3 n = 12 b = 331 mm h = 602 mm d = 582 mm determine the ff. 1. What is the distance from the top fiber of the beam to the neutral axis in mm? 2. What is the gross moment of inertia of the section in mm4? 3. Compute the moment capacity of concrete in kN-m. 4. Compute the moment capacity of steel in kN-m. 5. Aside from the uniformly distributed self-weight of the reinforced concrete, what will be the maximum two equal concentrated loads it can carry that will be located at its third points in kN? pls solve completely
Reinforced And Prestressed Concrete PROBLEM: A reinforced rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1 layer at the tension side. The beam has a stirrup with a diameter of 10 mm. Use fc=28 Mpa and fy=420 MPa b= 197.5 mm d= 317.5mm L= 2.7 Wd = 13.75 kN/m WL = 17.75 kN/m Calculate the nominal moment capacity of the beam Calculate that strain of the tension bars. Calculate the strength reduction factor of the beam
A simply supported beam 300 mm wide, 500 mm deep and spans 5.2 m supports a service super imposed dead load of 12 kN/m and service live load of 8 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. 1. Determine the maximum ultimate moment (in kN-m) the beam must resist using load combination of NSCP 2015 a. 116.64, b. 115.02, c. 109.44, d. 106.54 2. Determine the required depth of uniform stress block (in mm) upon crushing of concrete when ultimate load is applied. a. 60.54, b. 56.52, c. 54.92, d. 65.54 3. Determine the required amount of tensile reinforcement (in mm^2) a. 775, b. 729, c. 781, d. 708
Calculate the stresses in members AB, DF, and BD. Given:FAB = 51.22 kN (C)FDF = 50 kN (C)FBD = 32.98 kN (C)d = 0.05 m
The simply supported I-beam is to carry a uniform distributed service dead load and live load totaling0.65 kips/ft over the 50 ft span, in addition to its own weight of 384 lb/ft. The beam will be pretensioned using multiple of seven-wire Grade 270 strands steel. Eccentricity is constant and equal to 12.5 in. The prestress force immediately after transfer is 432 kips. Prestress force due to time –dependent losses is equal to 267 kips. Properties of the beam cross-section: Ac = 369 in2 Ig = 50979 in4 c1 = 20.17 in c2 = 15.83 in r2=138 in2 a) Determine the concrete stress due to initial prestressing force only. f1, f2 b) Determine the concrete stress due to prestressing force plus self-weight only after all important losses occurred. f1, f2 c) Determine the concrete stress due to prestressing force and full service load after all important losses occurred. f1, f2
Design a rectangular reinforced beam that is simply supported with a span of 15 ft. The beam is to carry a service dead load of 1.27 k/ft and service live load of 2.15 k/ft. Use fy = 60,000 psi and f’c = 4,000 psi and Wu=1.2DL + 1.6LL. Sketch the beam section.
A simply-supported rectangular beam with an 8 m span has a self-weight of 5.5 kN/m and an imposed load of 12 kN/m. In addition to this, the beam supports a brickwall with a thickness of 115 mm and a height of 3.2 m. Given: density of brick wall, ρbrickwall = 19 kN/m3 ; ? = 0.8; breadth of beam, b = 175 mm; concrete strength = 25 MPa; and fsy = 500 MPa. Assume the concrete cover is 30 mm and R10 shear links are used. a. Recommend a suitable depth for the beam and determine the area of reinforcement, Ast, according to minimum ductility requirements from AS3600 (ku = 0.36) by using N32 rebar. Detail the cross-section of the beam. b. Using the same beam dimensions from (a), design the steel requirement if N25 rebar is to be used instead. c. Based on your designs using N25 and N32 rebar, which rebar size would you recommend to the client? Justify your answer.
BADLY NEED IN 1HOUR PLS THANKYOU Above is a simple truss with P = 45.67 KN (write answers in kN in 2 decimals) Compute for the forces in: a. Member DA b. Member BH c. Member HI d. Member DG e. Member El f. Member AF g. Resultant Force Reaction of Support F (3 pts)
A short spiral column carries an axial dead load of 118 kN and an axial live load of 235 kN. Use fc’ = 27.5 MPa, fy = 414 MPa. Use U = 1.2D + 1.6L, Ф = 0.65 1. Assuming ρ = 0.01, which of the following gives the diameter of the column section? * a. 200 mm b. 215 mm c. 220 mm d. 300 mm 2. Which of the following gives the number of 16 mm diameter main bars? a 3 pcs b. 4 pcs c. 5 pcs d. 6 pcs 3. Which of the following gives the spacing of spirals? a. 10 mm Ф b. 55 mm Ф c. 60 mm Ф d. 65 mm Ф