Problem 2: The Block A with a mass of 300 kg and placed on the sloped plane as shown below. The friction coefficient between the block A and the plane is equal to 0.1. Draw all forces that apply to the system and determine the acceleration of the system by drawing free body diagram and writing the needed motion equations. a o =30

Problem 2: The Block A with a mass of 300 kg and placed on the sloped plane as shown below. The friction coefficient between the block A and the plane is equal to 0.1. Draw all forces that apply to the system and determine the acceleration of the system by drawing free body diagram and writing the needed motion equations. a o =30

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum horizontal force P that can be applied to the 30-lb hoop without causing it to rotate. The coefficient of static friction between the hoop and the surfaces A and B is μs = 0.2. Take r = 300 mm.
Using Moments, Determine the friction force betweenA and B. if Block A has a mass of 100 kg and the coefficient offriction is 0.20.
With the help of a free body diagram, Replace the loading by an equivalent resultant force and couple moment acting at point O. Suppose that w=40lb/ft . Determine the couple moment.
A minimum force of P = 50 lb is required to hold the cylinder from slipping against the belt and the wall. Determine the weight of the cylinder if the coefficient of friction between the belt and cylinder is μs = 0.3 andslipping does not occur at the wall.
1. How much work UP is done by the force P = 45 N on the collar?UP = _______N·m 2. How much work Ug is done by gravity on the collar?Answer: Ug = ______ N·m 3. Determine the speed of the collar as it passes position B.v =______ m/s
A cylinder having a mass of 250 kg is to be supported by the cord that wraps over the pipe. Determine the largest vertical force F that can be applied to the cord without moving the cylinder. The cord passes (a) once over the pipe, β = 180°, and (b) two times over the pipe, β = 540°. Take μs = 0.2.
If the beam AD is loaded as shown, determine the horizontal force P which must be applied to the wedge in order to remove it from under the beam. The coefficients of static friction at the wedge’s top and bottom surfaces areμCA = 0.25 and μCB = 0.35, respectively. If P = 0, is the wedge self-locking? Neglect the weight and size of the wedge and the thickness of the beam.
The force system shown consist of a counterclockwise couple of 720 N-m plus a 1200 N force through the origin O, directed down to the left as specified. Determine the (a) distance between the forces and (b) intercepts of the single force at A(a,0) and B(0, b).
Consider water flow through a horizontal, short garden hose at a rate of 43 kg/min. The velocity at the inlet is 1.1 m/s and that at the outlet is 18 m/s. The hose makes a 90° turn to a vertical direction before the water is discharged. Disregard the weight of the hose and water. Taking the momentum-flux correction factor to be 1.08 at both the inlet and the outlet, the reaction force (in N, hint: the answer is a positive number) in the vertical direction required to hold the hose in place is ?
There is an inclined plane having an inclination of 30 degree with the horizontal. A body of mass 10 kg is kept on it. Calculate the maximum force required just move up the body (assume u=0.42)
Knowing that at the instant shown crank BC has a constant angular velocity of 45 rpm clockwise, determine the acceleration of Point A and Point D.
The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for all contacting surfaces is µ = 0.268. Determine the following: a. What value of P in kN would be required to push to the right the wedge under the block? b. What value of P in kN would be required to pull to the left the wedge under the block? Assume the block A is stll in contact with the wall just as motion starts.