answer problem #2 write your solution on any peace of paper thank youuuuyuuy Problem Solving. Solve the following problems completely. Write your solution in a separate short bond paper.BOX your final answer.Problem 1. A 50-kW, 250-V short-shunt compound motor has the following data: R₂ = 0.06 2, R = 0.04 2 andR₁ = 125 £2. Calculate the induced armature voltage at rated load and terminal voltage. Take 2 V as the total brush-contact drop.Problem 2. A 60-hp 230-volt shunt motor has a shunt-field resistance of 38.3 ohms and an armature resistance of0.04 ohm. if the resistance in the starter is 0.66 ohm, calculate the current input to the motor at the instant it is started(assume 3-volts brush drop)

Given, Power, P=60 hp=60×746=44.76 KW Terminal voltage, VT=230 V Shunt field resistance, Rsh=38.3…

Problem 2. A 60-hp 230-volt shunt motor has a shunt-field resistance of 38.3 ohms and an armature resistance of 0.04 ohm. if the resistance in the starter is 0.66 ohm, calculate the current input to the motor at the instant it is started (assume 3-volts brush drop)

Problem 2. A 60-hp 230-volt shunt motor has a shunt-field resistance of 38.3 ohms and an armature resistance of 0.04 ohm. if the resistance in the starter is 0.66 ohm, calculate the current input to the motor at the instant it is started (assume 3-volts brush drop)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 19RQ: Why is the starting torque per A of starting current of a wound-rotor motor higher than that of a...

See similar textbooks

Similar questions

A 220 V dc shunt motor takes 5A and 40A at no load and full load respectively. It has an armatureresistance of 0.2 ohm and field resistance of 110 ohm respectively. Iron, Friction and Windages lossesare negligible. Then using among parameters find following: 1. Calculate an emf at no load of dc motor 2.Determine the armature current at full load 3. Determine armature current at no load 4.Calculate an emf at full load
a 220v dc shunt motor takes 5a and 40a at no load and full load respectively it has an armature resistance of 0.2 ohm and field resistance of 110 ohm respectively. iron,friction and windages losses are negligible.then using among parameters find following. calculate emf at full load of dc motor
A 230-V, 60-Hz, 6-pole, Y-connected, three-phase induction motorhas the following parameters in ohms/phase as referred to thestator: R1 = 12.5, X1 = 21.3, R2 = 28.6, X2 = 13.6, Rc = 4200, andXm = 1800. The friction and windage loss is 3% of the powerdeveloped. If the rotor speed is 1125 rpm, and using the exactequivalent circuit diagram determine the following:(i) the input power,(ii) the stator copper loss,(iii) the rotor copper loss,(iv) the air-gap power,(v) the power developed,(vi) the torque developed,(vii) the efficiency, and(viii) draw the power flow diagram
A 230-V, 60 Hz, single phase synchronous motor is taking a current of 20 A at 0.866 lagging pf. Effective armature resistance is 3 ohms. Iron and friction losses amount to 45 o W. Determine the efficiency of the motor at this load. Neglect losses in the excitation.
1. A 10-hp, 4-pole, 25-Hz, 3-Ф induction motor is taking 9,100 watts from the line. The core loss is 290 watts; stator copper loss is 568 watts; rotor copper loss is 445 watts, and the friction and windage loss is 121 watts. Determine the output torque in Newton-meter. 2. For a three-phase induction motor having rotor circuit resistance of 6 ohms, maximum torque occurs at a slip of 0.6. Find the value of standstill rotor circuit reactance. 3. A 4 - pole, 3 - phase, 60 Hz squirrel-cage motor draws 21 A and 7 kW while driving its normal load. Under these conditions, its slip is 2%. When running idle, this motor draws 6 A and 580 W at normal voltage. With its rotor blocked, this motor draws 15 A and 500 W with 50 V applied. What is the output torque of this motor when driving its normal load. 4. A 4-pole, 50 Hz, 3- phase induction motor develops a maximum torque of 110 N-m at 1360 rpm. The resistance of the star-connected rotor is 0.25 Ω /phase. Calicul the value of resistance that must…
A 120V dc shunt motor has an armature resistance of 0.25Ω is drawing 50A. If a fixed loss of 200W was measured and neglecting the shunt field, what is the copper loss (in watts)? (meaning no shunt field used)
1- A 10kW, 200V, DC Shunt motor has 1-ohm armature resistance. At the starting of the motor, its back emf (Eb) is zero.Select one:TrueFalse 2- Identify which of the following loss is not varying with respect to load current? a.Iron loss b.Both Armature and Series field copper losses c.Series field Copper Loss d.Armature Copper Loss
the step-by-step solution needed with calculation. 45) A 40hp, 440V, 4 pole dc motor has an armature wave-wound with 846 conductors and the commutator has 141 segments. The full load efficiency is 85% and the shunt current is 1.25A. If the brushes are shifted backward through segments from the geometric neutral axis, calculate (a) The demagnetizing ampere-turns per pole (b) The distorting ampere-turns per pole on full load. the previous one is wrong.
a shunt-wound motor runs at 600 r.p.m from a 230 V supply when taking a line current of 50 A. its armature and Field resistance are 0.4 ohms and 104.5 ohms respectively. Neglecting the effects of armature reaction and allowing 2 V brush drop, calculate (a) the no-load speed if the no-load line current is 5 A. (b) the resistance to be placed in armature circuit in order to reduce the speed to 500 r.p.m when motor is taking a line current of 50 A . (c) the percentage reduction in the flux per pole in order that the speed maybe 750 r.p.m when the armature is 30 A with no added resistance in the armature circuit.
A 480 V, 60 Hz, 400 hp synchronous motor with a power factor of 0.8 inlead, with eight poles, connected in D, has a synchronous reactance of 0.6 V andnegligible resistance in the armature. Ignore friction losses,by friction with the air and in the core HELLO ONLY POINTS D) AND E) PLEASEa) What is the speed of this motor?b) Draw the phasor diagram of the motor with an initial load of 200 HP and findthe values of Ia, lL and EA:c) Assume the shaft load is increased to 400 horsepower rating.Find lA, IL, and EA after the change in charge. What is the new factor ofengine power? Draw the phasor diagram reaction in response to thischange.d) What is the torque developed by the synchronous motor at 200 HP and 400 HPe) What is the maximum torque developed by the synchronous motor?
I need Answer of both A & B A 6-pole, 50-Hz wound-rotor induction motor when supplied at the rated voltage and frequency with slip-rings open-circuited, developed a voltage of 100 V between any two rings. Under the same conditions its rotor is now driven by external means at (a) 700 rpm opposite to the direction of rotation of stator field, and (b) 900 rpm in the direction of rotation of stator field. Find the voltage available between slip-rings and its frequency in each of these cases.
A separately-excited d.c motor has an armature resistance of 1.1Ω and the excitation circuit is connected to a fixed d.c source, such that k = 1.4V/rad/s. The mechanical losses are negligible. The motor is supplied from a constant 170V d.c source and loaded with a rated torque of 26 Nm. I t is required to reduce the speed of the motor by inserting resistance in the armature circuit or by reducing the armature voltage. How much resistance should be added in series with the armature of the motor, in order that the steady-state speed is half of the rated speed at the full load torque? How much must the applied armature voltage be reduced in order to achieve the same speed in part (i) for the same load? Determine which of the two methods is more efficient.