Problem #2. The pipe assembly is subjected to the 80 N force. Determine the moment about the points A and B. Express the answers in the Cartesian vector notation. 400 mm 300mm 200 mm 200 imm 250 mm 30 F-80 N

Q: 5. A fluid undergoes a reversible adiabatic compression from 0.5 MPa, 0.2m to 0.05 m according to th...

A:

Q: Consider a steady, incompressible flow between two parallel plates. The top plate at a temperature T...

A: Write the expression of shear stress. τ=μdudy  

Q: Explain the hydraulic cycle in nature with the help of a neat sketch, indicating its various phases.

A:

Q: In an engine working on Dual cycle, the temperature and pressure at the beginning of the cycle are 9...

A:

Q: 4) The criterion of constraints for a kinematic chain having plane motion is given by the equation:

A: Solution to Q4 as mentioned by the student:

Q: A tractor operating at 3.5 mph develops 3000 pounds drawbar pull in pulling a trailer. Estimate the ...

A: Answer: The required drawbar horsepower of the tractor is 28 hp.  

Q: Water drains from a pressurized tank (50 kPa gage) through a 0.1m-diameter pipe system at a rate of ...

A: Given:d=0.1 mQ=0.0371 m3/sρ=1000 kg/m3μ=1.12*10-3 Ns/m2

Q: A hot water pump pumps water from a tank (known as the condenser) up to a storage tank- boiler. The ...

A:

Q: Find the angle ß. y 29 kips 1 39° 18° The tolerance is + 1 in the 3rd significant digit. Answer:B = ...

A:

Q: The pipes at A and B contain oil and the inclined tube manometer is filled with oil and mercury. Det...

A:

Q: determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is n...

A:  Need to determine the required diameter 

Q: The transfer function of a system is given by 2000(s + 1) G(s) = s(s + 10)(s + 40) a) Sketch the bod...

A:

Q: 6) The number of degrees of freedom of a planar linkage with 8 links and 9 simple revolute join ts i...

A:

Q: At a full draw, an archer applies a pull of 130 Nto the bowstring of the bow shown in the figure. De...

A:

Q: What is zeroth law of thermosynamics

A: The zeroth law of thermodynamics states that if two system are in thermal equilibrium with a third s...

Q: he maximum thermal efficiency possible for a power cycle operating between 1200°F and 225°F is: The ...

A: Given:T1=1200°FT2=225°F

Q: In a turning operation, the workpiece diameter is Dm=44.00 mm and the diameter after the operation s...

A: Given:Dm=44 mmDc=22 mmV=15 m/minf=0.03 mm/rev

Q: The following four cargoes have been offered for shipment on an upcoming flight as space is availabl...

A:

Q: Determine the forces in the members identified by “x" of the truss shown by the method of sections. ...

A: Given: point M and point A is hinged and link MH is in the horizontal direction so force in the link...

Q: A disc is rolling on horizontal plan without slipping as shown in given figure. Point P has linear v...

A: Given: A disc rolling on horizontal plane without slipping,Velocity of point P, Vp=1 m/s

Q: In the talk on precise positioning of drones: an approach to different technologies, which of the fo...

A: Correct answer: Amazon

Q: A cylindrical container with a surface area of 150 cm2 contains 1 liter of water and 2 liters of mer...

A:

Q: Find the point of view lines of the given

A: Point of view at AB in HRP

Q: 2. Find the Moment about A and B for the forces acting on the body shown below. The forces acting at...

A: Moment about a point is the product of force and perpendicular distance between point and force. It ...

Q: Question 1: If through a simple experiment as shown below, the angle of repose between the crate and...

A: To determine the value of coefficient of static friction.

Q: A venturimeter is attached to pipe of 80 mm diameter has throat of 40 mm diameter. It is found that ...

A:

Q: Fluid flows through a pipe with 2 elbows and a valve for which the values of K are 1 and 5, respecti...

A: Loss coefficient for elbow, Kel=1Loss coefficient for valve, KV=5Pipe diameter, d=0.1 mFluid velocit...

Q: A piston cylinder arrangement initially contains 7.0 kgs of super- heated steam at 500 kPa and 250 C...

A:

Q: 10) A six-link chain with no higher pairs has 5 binary joints and 1 ternary joint. The chain is best...

A: Dear student,                     According to the guidelines I am allowed to answer only one proble...

Q: A welded joint of circular shaft as shown in figure is subjected to an eccentric load of 2.5 kN. If ...

A:

Q: In a compound helical spring, the inner spring is arranged within and concentri outer one but is 10 ...

A:

Q: ves at 35°C. For liquid me +0.025(Pe)"; where Pe rcury at 25°C are:- 32 kg/m' C, = 140J/kg K, -10-7 ...

A:

Q: the most suitable grindirg i firafion

A: Given; Base of a brass bracket needs rough grinding, For this purpose find suitable grinding wheel g...

Q: When a hydrocarbon fuel is burned, almost all of the carbon in the fuel burns completely to form CO2...

A: 0.59 kg of CO2 is produced for each kWh of electricity generated from a power plant that burns natur...

Q: A balanced rigid disc mounted on a rigid rotor has four identical point masses, each of 10 grams, at...

A: Given data: m=10 g=0.001 kgr=100 mm=0.1 mω=10 rad/s Need to determine the magnitude of the resultant...

Q: In a pipe with constant flow rate, if diameter of pipe is halved and length of pipe is doubled, then...

A:

Q: The work needed to isentropically compress 5 kg of air in a cylinder at 500 kPa and 600°C to 6 MPa i...

A:

Q: Calculate the lift and moment coefficients using thin airfoil theory approximations for a range of a...

A: Thin airfoil theory Thin airfoil hypothesis is a direct theory of airfoils that relates approach to ...

Q: A cylinder of mass m, radius r and radius of gyration k is released from rest and rolls without slip...

A:

Q: A mass of 7 kg undergoes a process during which velocity decreases from 32 m/s to 19m/s, while the e...

A: Givenm=7kgv1=32m/sv2=19m/su1=1.24kJ/kgu2=2.08kJ/kgQ1=2kJQ2=-0.8kJ

Q: A bar with a rectangular cross section is connected to a support bracket with a circular pin as show...

A: Find the maximum allowable  load 

Q: The motion of a particle is defined by the relation x = 2t^3 - 15t^2 + 24t + 4, where x is expressed...

A: Given data,  x= 2t³-15t²+24t+4  Here t = time in second  

Q: What type of axle housing resembles a banjo?

A: Given Data : Banjo

Q: An isosceles triangular plate of base 4 m and altitude 4 m is immersed vertically in an oil of sp. g...

A: The total pressure is defined as the force exerted by a static fluid on the surface either plane or ...

Q: Which of the ff are methods to adjust the gaps in centerlines ¢er marks? A. Center B. Center2 C. Cen...

A: Different types of lines used in AutoCAD are: Continues line Center Line Hidden Line

Q: 0.5 kg of a certain gas is contained within a piston-cylinder assembly. The gas undergoes a process ...

A:

Q: 2) After playing a game of pinball, you decide to do some calculations on the launching mechanism. T...

A:

Q: ze, is to transmit 7 kW at 1000 rpm. The inner radius of the contact is 50 mm and outer radius of th...

A:

Q: Specific Heat Problems: a. The boiler in a canteen contains 6.75 kg of water at 10°C. How much heat ...

A:

Q: balloon which was originally empty is being filled with hydrogen from a cylinder at a constant tempe...

A: Given data: T=300 KP=1.01325 bar=101.325 kPad=6 m Need to determine the work done by the balloon–cyl...

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.