Problem 3 Consider the channel section shown. (a) Find the flow area (A), wetted perimeter (P) and top width (T) for the case when water depth y> h. Report your answers in terms of the notation on the sketch. b₂ b₂ (b) Calculate numerical values of A, P, R, T and D for b1 = 4.5 ft, b2=2.5 ft, h=1.7 ft, z1 = 1, z2 = 1.5 for y = 3.0 ft and y = 1.0 ft i. ii.

Problem 3 Consider the channel section shown. (a) Find the flow area (A), wetted perimeter (P) and top width (T) for the case when water depth y> h. Report your answers in terms of the notation on the sketch. b₂ b₂ (b) Calculate numerical values of A, P, R, T and D for b1 = 4.5 ft, b2=2.5 ft, h=1.7 ft, z1 = 1, z2 = 1.5 for y = 3.0 ft and y = 1.0 ft i. ii.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

*hydraulics *use handwritten A rectangular channel 5.50 m wide and 1.30 m deep is laid on a uniform slope of 0.002. The roughness coefficient of the channel is 0.013. 1.) Which of the following most nearly gives the rate of flow in the channel in m^3/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67 2.) Which of the following most nearly gives the saving’s in lining per meter length of channel that could have been offered by using the most efficient rectangular section but adhering to the same flow capacity and slope in m^2/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67 3.) Which of the following most nearly gives the savings in earth excavation per meter length of channel that could have been offered by using the most efficient rectangular Section but adhering to the same flow capacity and slope in m^3/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67
Water discharges from under a sluice gate into 10 m wide channel (slope = 0.001) at a flowrate of 28 m3/s as shown below. Assume n = 0.015. 1- Find critical and normal depths? 2- Classification of the water surface profile? 3- Quantitatively evaluate the profile downstream the gate until water surface height is 30 cm above the channel bottom? 4- where does the hydraulic jump start? Note: it is required to draw surface water profile
Pls answer Determine the other alternated depth in meters of the rectangular channel section (width = 3 meters) with a different flow rate. Section 1 depth = 3m Section 1 flow rate = 10 m3/s Section 2 flow rate = 10 m3/s
Water flows in a trapezoidal channel 3m wide and has a side slope of 1 vertical to 2 horizontal. The bed slope is 1:5000 and depth of flow is 1.5m. Find the flow rate if Manning's constant is 0.025
*hydraulics *use handwritten A rectangular channel 5.50 m wide and 1.30 m deep is laid on a uniform slope of 0.002. The roughness coefficient of the channel is 0.013. Which of the following most nearly gives the saving’s in lining per meter length of channel that could have been offered by using the most efficient rectangular section but adhering to the same flow capacity and slope in m^2/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67 note: the unit should be in m^2/s.
*hydraulics *use handwritten A rectangular channel 5.50 m wide and 1.30 m deep is laid on a uniform slope of 0.002. The roughness coefficient of the channel is 0.013. Which of the following most nearly gives the saving’s in lining per meter length of channel that could have been offered by using the most efficient rectangular section but adhering to the same flow capacity and slope in m^2/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67 Which of the following most nearly gives the savings in earth excavation per meter length of channel that could have been offered by using the most efficient rectangular Section but adhering to the same flow capacity and slope in m^3/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67
Water flows in a brickwork rectangular channel 2.5 m wide, on a slope of 5 m/km. For brickwork, take n = 0.015. 1.Find the flow rate when the normal depth is 50 cm. Round the final answer to two decimal places. 2. If the normal depth remains 50 cm, find the channel width which will triple the flow rate. Round the final answer to two decimal places.
Water flows in a trapezoidal channel 3m wide and has a side slope of 1 vertical to 2 horizontal. The bed slope is 1:5000 and depth of flow is 1.5m. Find the flowrate if Manning's constant is 0.025.
Please Solve Part B SOLVE IT AND ALSO PLOT THE fIGURES A rectangular channel is 3m wide and has a depth of flow of 1.5m. The channel roughness can be assumed to be 0.015 and the bed slope is 0.001. Calculate The height by which the bed should be raised to just produce critical depth The width by which the bed should be narrowed to just produce critical depth
The earth dam shown in the is to be built on gravelly sand with silt and cobbles. Thisdam will extend a distance of 850 ft perpendicular to the cross-section. To reduce the flow ratethrough these soils, a concrete cutoff wall will be built as shown. Redraw this cross-section to ascale of 1 in = 100 ft, draw a flow net, and compute Q. Then, identify the area in the flow net thathas the greatest hydraulic gradient.
A rectangular channel 1.25m wide and 30m long with a flat bottom carries a flow of 0.5m3/s. The channel terminates in a free discharge. Plot a sketch of the water profile in the channel. Take n = 0.011. [10 Marks] b) Find the depth for uniform flow in a trapezoidal channel side slopes 1 in 2, and bottom width 3m, when the flow rate is 6m3/s if So = 0.0006 and n is assumed to be 0.016. Compute the corresponding value of e. [10 Marks]
Water flows in a trapezoidal channel with side slope 1V:3H, bottom width of 16 ft and water depth of 4.5ft. The channel bottom drops 0.1ft every 100ft. Length, n=0.015. Show Complete Solutiona. Compute the velocity in ft/s (using Manning, Kutter)b. Compute the flow rate in ft3/s (using Manning, Kutter)