Problem 3: Note: Make sure to draw all diagrams. All Units must be included. 1. Determine the stretch in each of the two springs required to hold the 20kg crate in the equilibrium position shown. Each spring has an un- stretched length of 2m and a stiffness of k=300N/m. Ans. S 0.218m, S, = 0.327m B 12 m Draw Free-Body Diagram(s) Write Equations of Equilibrium 1. 2. 6 m 3. Solve for all unknown forces 4. Find the Stretch in each of the two springs

Problem 3: Note: Make sure to draw all diagrams. All Units must be included. 1. Determine the stretch in each of the two springs required to hold the 20kg crate in the equilibrium position shown. Each spring has an un- stretched length of 2m and a stiffness of k=300N/m. Ans. S 0.218m, S, = 0.327m B 12 m Draw Free-Body Diagram(s) Write Equations of Equilibrium 1. 2. 6 m 3. Solve for all unknown forces 4. Find the Stretch in each of the two springs

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

N.6.1. Find principle stress if the values are as given: Upper side stress:300lb/9pulg2 Tangential in right direction: 120 lb/pulg2
A = 3 B = 4 C = 1 D = 0 kindly answer the magnitude and if possible the forces
10.24 A concrete canoe in storage is supported by two rope slings, as shown. each sling supports 48lb. The rope has a tensile breaking strength of 252lb. Determine the maximum value of theta if there is to be a factor of safety of 4.0 against breaking.
The ends of a 0.25kg rod AB are constrained to move along slots cut in a vertical plate as shown. A spring of constant k=3N/m. is attached to end A in such a way that its tension is zero when θ=0°. the rod is released from rest when θ=45° (position 1) until it reaches θ=0° (position 2) Is the work done by the weight of the rod negative and positive for the spring? Please explain.
There is a cylinder X weighing 735.75 Newtons that is held against a smooth incline and is being supported by a weightelss rod Y at 20°. Calculate all the forces that is acting on cylinder X. Draw FBD pls thank you.
Only accepted correct answer is 2.84. Please show solution. A steel plate 2.2 m x 1.4 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the vertical displacement of the steel plate when suspended if the sling cable is 55 sq.mm. in area.
NEED HELP ASAP PLEASE!!! A horizontal shelf AD of length L = 740 mm, width b = 360 mm, and thickness t = 30 mm is supported by brackets at B and C [see part (a) of the figure]. The brackets are adjustable and may be placed in any desired positions between the ends of the shelf. A uniform load of intensity q. which includes the weight of the shelf itself, acts on the shelf [see part (b) of the figure]. A L (a) D L (b) Determine the maximum permissible value of the load if the allowable bending stress in the shelf is Oallow = 7.5 MPa and the position of the supports is adjusted for maximum load-carrying capacity. Round to two decimal places. qmax kN/m
# = poundsa) what is the shear force at 5' rt. of A? (in pounds, 2 decimal places)b) what is the bending moment at 5' rt. of A? (in pounds, 2 decimal places)
The rigid bar ABC shown in the figure below is hinged at A and supported by a steel rod at B. Determine the largest load P (kips) that can be applied at C if the stress in the steel rod is limited to 24 ksi and the vertical movement of end C must not exceed 0.15 in. Where L1 = 2.2 ft and L2 = 3.2 ft. Your final answer should have two decimal places
Solve under 30 min pls i awill give a like
Three forces are applied in a system whose resultant is zero, one of the force is unknown: F1 (70lbs, 45deg NE), F2 (80 lbs, 65deg SE). Compute the horizontal force (lbs) of the unknown force.
A pull of 6,500 lb is applied to a steel rod which has an ultimate stressof 65,000 psi. Determine the steel rod diameter if the factor of safetyis 5.A. 0.998 inch C. 0.798 inchB. 0.598 inch D. 0.398 inch