Need right complete solutionStep by step please Problem 4 Design of Flexural MembersA W 16 x 26 is used for beam AB as shown in the figure. Service deadloads consists of 125 mm thick reinforced concrete slab. Assume thatthe floor slab provides continuous lateral support.Partition load (movable, live) = 0.96 kPa, Suspended ceiling andmechanical equipment = 0.48 kPa. Service live load = 3.12 kPa and unitweight of concrete = 24 kN/m³.Properties of W 16 X 26Wt. =39 kg/mA = 4955 mm²d398.53 mm9 т.bf = 139.70 mmtf = 8.76 mmtw = 6.35 mmВSx = 629 x 103 mm3Sy= 57 x 103 mm³1.81.81.81.8Zx = 724 x 103 mm3Zy= 90 x 103 mm3Fy= 345.6 MPaa. Determine the design flexural strength capacity of the beam.Ø =0.90 (kN-m)b. Determine the design shear strength capacity of the beam. (kN)c. Determine the deflection of the beam if it has a flexuralrigidity of 23800 kN-m² based on live load only.d. Is the beam adequate for live load deflection limit as per code?

Answered: Image /qna-images/answer/2ffb4a7a-71b8-4414-8cdd-dac4ab9a2d12.jpg

Problem 4 Design of Flexural Members A W 16 x 26 is used for beam AB as shown in the figure. Service dead loads consists of 125 mm thick reinforced concrete slab. Assume that the floor slab provides continuous lateral support. Partition load (movable, live) = 0.96 kPa, Suspended ceiling and mechanical equipment = 0.48 kPa. Service live load = 3.12 kPa and unit weight of concrete = 24 kN/m³.

Problem 4 Design of Flexural Members A W 16 x 26 is used for beam AB as shown in the figure. Service dead loads consists of 125 mm thick reinforced concrete slab. Assume that the floor slab provides continuous lateral support. Partition load (movable, live) = 0.96 kPa, Suspended ceiling and mechanical equipment = 0.48 kPa. Service live load = 3.12 kPa and unit weight of concrete = 24 kN/m³.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A floor slab 100 mm thick is cast monollthically with beams 250 mm wide 450 mm deepspaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports asuperimposed service dead load of 1.0 kPa and service live load of 2.1 kPa. Using f.=21MPa, long bar f, = 415 MPa, calculate the following:Factored uniform load on a typical interior beam in kN/m using load factors of 1.2for dead load and 1.6 for live load.A. 8.928B. 11.448C. 11.028D. 9.960Effective flange width of a typical interior beam in mm.A. 1,500B. 1.850C. 1.200D. 1.466Required amount of 16-mm-flexure bars for a typical interior beam in positivebending. Use 10-mm-dia. stirrupsA. 512 mm2B. 246 mm2C. 331 mm2D. 427 mm2
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
A floor is supported by 75 mm x 200 mm wooden joists spaced at 400mm on centers with an effective span of 3m. The total floor load transmitted to the joists is 5kPa. If the unit weight of wood is 6.3 kN/m3 and elastic modulus of wood is 12x103 MPa. W Tributary 400 6001 mm -3m Was kPa FO 400 in Floor (a) Determine the maximum bending stress (fb). (b) Determine the maximum shearing stress (fy). (c) Determine the maximum deflection
The uniformly distributed live load on the floor plan in Figure P2.4 is 60 lb/ft2 . Establish the loading for members (a) floor beam B1, (b) floor beam B2, (c) girder G1, and (d) girder G2. Consider the live load reduction if permitted by the ASCE standard.
Calculate the total equivalent uniform load in KN/m on Beam BE, if the total floor load is 13.80KPa. Use a=3.5m, b=5m . Express your answer in 2 decimal places.
Calculate the governing load combination for a secondary beam with effective width = 2.0 m Dead load Weight of slab = 3.0 kPa Ceiling services = 1.0 kPa Self-weight of beam = 1.0kN/m Imposed load - 0.2 kPa
A concrete framework is used to support a 125 mm reinforced concrete slab thatcarries a uniform live load of 12 kN/m2. The concrete density is 24kN/m3. The sizeof beam is 200 mm x 350 mm.There is a 125 mm thick brickwall on beam AD andCD. The walls are 3 m in height. Show the calculation of the design load of ColumnD in Figure 1.
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 1.5 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c= 21 MPa, long bar fy = 415 MPa, calculate: Factored uniform load on a typical interior beam in kN/m using load factors of 1.2 for dead load and 1.6 for live load.
Determine the Pn of the following column assuming it had no moment on it and only an axial compression force: (f’c = 6000 psi, Grade 60 bars, h = 20”, b = 12” (i.e. rectangular section), tied column). Do not worry about calculating φ (phi factor). You can assume it is a short column. Also assume a reinforcement ration of 2% (ρg = 0.02).
A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2263 sq. mm at the bottom, and 1232 sq. mm on the top. Take d' = 70 mm, fc' = 21 MPa, and fy = 345 MPa. determine 1.) a 2.) the value of fs' (actual stress of the compression bars) 3.) value of ρbalance 4.) Mu
The partial plan layout for the framed structure of a multistory building is shown below. The vertical structure consists of columns and the horizontal floor structure of a one-way deck and beam system. The uniformly ultimate (factored) distributed load for the one-way-spanning deck is equal to 0.14 kip/ft2. Ignore the own weights of beams and walls. L1 = 22 ft, L2 = 22 ft, L3 = 32 ft. Compute the load on column 1. Compute the value of distributed load on beam A. Compute the value of concentrated loads on beam C. Draw the shear and bending moment diagrams for beam C (with values) – Assume beam C as simply supported.
A small balcony constructed of wood is supported by three identical cantilever beams (see figure). Each beam has length L, = 2.3 m, width b, and height h = 3b/2. The dimensions of the balcony floor are L, x L2, with La = 2.7 m. The design load is 6.5 kPa acting over the entire floor area. (This load accounts for all loads except the weights of the cantilever beams, which have a weight density y = 6.5 kN/m^3 --) The allowable bending stress in the cantilevers is 45 MPa (a) Assuming that the middle cantilever supports 50% of the load and each outer cantilever supports 25% of the load, determine the required dimension b. Round to the nearest whole number. mm (b) Assuming that the middle cantilever supports 50% of the load and each outer cantilever supports 25% of the load, determine the required dimension h. Round to the nearest whole number. h = mm