Solution must be handwritten take note that final answer must be in ft PROBLEM 4: The basic barometer can be used to measure the height of abuilding. If the barometric readings at the top and at the bottom of abuilding are 29.7" and 28.7" Hg, respectively, determine the height of thebuilding in feet. Assume an average air density of 0.0023 slug/ft3 (1 slug =32.174 Ib) and SG of Hg 13.55.*P = 28.7" Hg%3Dtoph = ?Pbot= 29.7" Hg

Hello dear this is the solution of your problem The answer is found to be Height of building is…

PROBLEM 4: The basic barometer can be used to measure the height of a puilding. If the barometric readings at the top and at the bottom of a puilding are 29.7" and 28.7" Hg, respectively, determine the height of the building in feet. Assume an average air density of 0.0023 slug/ft3 (1 slug = 32.174 Ib) and SG of Hg = 13.55.* Pop = 28.7" Hg h ? Pbot= 29.7" Hg

PROBLEM 4: The basic barometer can be used to measure the height of a puilding. If the barometric readings at the top and at the bottom of a puilding are 29.7" and 28.7" Hg, respectively, determine the height of the building in feet. Assume an average air density of 0.0023 slug/ft3 (1 slug = 32.174 Ib) and SG of Hg = 13.55.* Pop = 28.7" Hg h ? Pbot= 29.7" Hg

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.6P

See similar textbooks

Similar questions

A Venturi meter 45 cm by 20 cm has its axis inclined upwards 30 degrees from the horizontal. The distance measured along the axis, from the inlet to the throat is 1.20m. The differential manometer connected at the inlet and throat shows a deflection of 25 cm of mercury. If the flow is upward and the flowing fluid has specific gravity of 2.0, find the discharge and the pressure head difference between the inlet and throat if the meter coefficient is 0.96
Determine the height of the building in feet, if the barometer reading at the top of the building is 751 mmHg while the barometer reading at the bottom of the building is 101,325 Pa. Assume the density of the air is 1.8 kg/m³ and that of mercury is 13,600 kg/m³.
If the quantity of air discharged at D is 1,500 m3/min and friction factor of 0.0048, calculate the following: (a) the quantity of air discharged at C; (b) static pressure at fan outlet A. Group of answer choices 3203.2 m3/min; 14.75 N/m2 2203.2 m3/min; 24.75 N/m2 2203.2 m3/min; 14.75 N/m2 4203.2 m3/min; 14.75 N/m2please show complete solution for review and analysis purposes
A Venturi meter 45 cm by 20 cm has its axis inclined upwards 300 from the horizontal. The distance measured along the axis, from the inlet to the throat is 1.20m. The differential manometer connected at the inlet and throat shows a deflection of 25 cm of mercury. If the flow is upward and the flowing fluid has specific gravity of 2.0, find the discharge and the pressure head difference between the inlet and throat if the meter coefficient is 0.96.
Please answer all. I will rate. Points A and B are 5 km apart along a new 60 cm diameter cast iron pipe carrying water. A is 9m higher than B. If the pressure at B is 140 KPa greater than at A. f= 0.019 Determine the head loss in meters. choices: 7.25, 5.27, 2.75, 7.52 Determine the flow rate in lit/sec. choices: 522.88, 822.55, 885.22, 228.55
b) How to Calibration of Air Velocity from Pressure Using Sub-Sonic Wind Tunnel?c) Write the components of Sub-Sonic Wind Tunnel?
Read the question carefully and give me right solution according to the question. Velocity =0.46 m/sec
Water flows at 0.07 cubic meter per second through a pipe. A horizontal venturi meter with throat diameter of 150-mm was used to measure the velocity inside the pipe. Based on manometer reading, the differential gauge is deflected 1.2 meter. If the specific gravity of the manometer fluid is 1.60, the velocity, in meter per second (m/s), of water inside the pipe is Blank 1
Water flows at 0.07 cubic meter per second through a pipe. A horizontal venturi meter with throat diameter of 150-mm was used to measure the velocity inside the pipe. Based on manometer reading, the differential gauge is deflected 1.2 meter. If the specific gravity of the manometer fluid is 1.60, the velocity, in meter per second (m/s), of water inside the pipe is ____ ANSWER ASAP
(Avoid truncation in the middle of solution thank you) The atmospheric pressure in a certain location was obtained to be 100 kPa Determine the gage pressure in kPa 2.0m below the surface of a body of liquid(specific gravity 1.50) in nearby lake 29.43 192.34 129. 93 92.43
Consider incompressible , frictionless flow of a fluid in a horizontal piping. The pressure and velocity of a fluid is measured to be 150 kPa and 1.25 m/s at a specified point. The density of fluid is 700 kg/m^3. If the pressure is 140 kPa at another point, the velocity ( in m/s )of the fluid at that point is Show FBD and choose the correct answer below A. 5.49 B. 5.39 C. 5.19 D. 5.29
40.) A large closed tank is filled with air under a pressure of 5.3 psi gage and at a temperature of 65°F. The air discharges into the atmosphere (14.7 psi) through a small opening in the side of the tank. Neglecting friction losses, compute the velocity of the air leaving the tank assuming (a) constant density of the air and (b) adiabatic flow conditions. ANSWER: 692 ft/sec, 728 ft/sec 41.) For Problem 40, if the pressure were 10.0 psi, what would be the velocity for (a) and for (b)? ANSWER: 855 ft/sec, 934 ft/sec