Problem 4: The beam is made from three boards nailed together as shown. If the moment acting on the cross section is 650 N.m A- Determine the centroid and the second moment of area (inertia) of the cross section B- Determine the maximum tensile stress in of the section C- Determine the maximum compressive stress of the section 15 mm 125 mm 20 mm 6000 M = 650 N-m 250 mm 20 mm

Problem 4: The beam is made from three boards nailed together as shown. If the moment acting on the cross section is 650 N.m A- Determine the centroid and the second moment of area (inertia) of the cross section B- Determine the maximum tensile stress in of the section C- Determine the maximum compressive stress of the section 15 mm 125 mm 20 mm 6000 M = 650 N-m 250 mm 20 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
A T section of a beam is fabricated from 2 - 12 mm x 150 mm steelplates and joined by welding as shown in Figure ST - 904. It carries a live loadof 6.5 kN/m extending half of its span. Neglect the weight 1. Compute the maximum compressive stress. ( bending stress incompression )2. Compute the maximum tensile stress. ( bending stress intension )3. Compute the maximum shear stress. 4. Compute the shear stress between the junction of web and flange. 5. Compute the maximum deflection. EI is constant.
A W 12 X 35 steel cantilever beam is subjectedto an axial load P =10 kips and a transverse loadV =15 kips. The beam has length L = 6 ft. (a) Calculatethe principal normal stresses and the maximumshear stress for an element located at C near the fixedsupport. Neglect the weight of the beam. (b) Repeat Parta for point D which is 4 in. above point C (see figure).See Table F-1(a), Appendix F, for beam properties.
Tow square bars are welded together and loaded axially as shown: Determine The normal stress between A&B The normal stress between B&C The normal stress between C&D The total change in length of the bar Assume : w1 =40 mm, w2 = 50 mm, P1 = 130 kN, P2= 65 kN, and P3 =260 kN. E = 200,000 Mpa original lengths LAB = 100 mm, LBC = 120 mm, and LCD = 130 mm,
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
A WT305 × 41 standard steel shape is used to support the loads shown. Assume w = 48 kN/m, LAB = 1.6 m, LBC = 3.2 m, and LCD = 1.6 m. Consider the entire 6.4 m length of the beam and determine:(a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and(b) the maximum compressive bending stress at any location along the beam (enter a negative answer). (c) Calculate the reaction forces at B and E. Forces are positive upwards.
Read the question carefully. Give me right solution according to the question. Find the load P in KN will make the simply supported beam yield due to bending stress if the yield stress is 250 Mpa. vertical load p is acting at mid-span. beam is made of steel E steel =200000 Mpa Ix=372*10^6 mm4 Y centroid=230 mm
Given: Four-25-mm-diameter rivets with an axial load of T= 75 kN distributed equally as shown. The thickness of the plates is 25 mm and width of plate is 150 mm. find (a) the shear stress on the rivets(b) the bearing stress between a plate and a rivet;(c) the minimum average tensile stress in each plate. *PLS DRAW THE FREE BODY DIAGRAM *USE 3 decimals
The simple beam shown, 76.2-cm. long ( = a + L + d ), is made of AISI C1022 steel, as rolled, left a forged. At a =25.4 cm , F1 = 1360.5 kg. is a dead load. At d = 25.4 in , F2 = 1088.4 kg. is repeated, reversed load. For N = 1.5 , indefinite life, and h = 3b , determine b and h . (Ignore stress concentration).
The plate welded to the end of the I-beam is fastened to the support with four 10-mm-diameter bolts (two on each side). Assuming that the load is equally divide among the bolts, determine the normal and shear stresses in a bolt. Express your answer in MPa.
A WT305 × 41 standard steel shape is used to support the loads shown. Assume w = 50 kN/m, LAB = 1.4 m, LBC = 2.8 m, and LCD = 1.4 m. Consider the entire 5.6 m length of the beam and determine:(a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and(b) the maximum compressive bending stress at any location along the beam (enter a negative answer).
A rigid bar of weight W = 800 N hangs from three equally spaced vertical wires (length L =150 mm, spacing a = 50 mm): two of steel and one of aluminum. The wires also support a load P acting on the bar. The diameter of the steel wires is ds = 2 mm, and the diameter of the aluminum wire is da = 4 mm. Assume Es = 210 GPa and Ea = 70 GPa.(a) What load Pallow can be supported at the midpoint of the bar (x = a) if the allowable stress in the steel wires is 220 MPa and in the aluminum wire is 80 MPa? (See figure part a.)(b) What is Pallow if the load is positioned at x =a/2?(See figure part a.)(c) Repeat part (b) if the second and third wires are switched as shown in the figure part b.