Problem 4.50 The chain AB exerts a force of 20 lb on the door at B. (Figure 1) Figure 1 of 1 20 4 ft 3 ft A 3 ft F = 20 lb B Part A Determine the magnitude of the moment of this force along the hinged axis of the door. Express your answer to three significant figures and include the appropriate units. M₂ = Submit μA Value Units My Answers Give Up Provide Feedback Continue

Problem 4.50 The chain AB exerts a force of 20 lb on the door at B. (Figure 1) Figure 1 of 1 20 4 ft 3 ft A 3 ft F = 20 lb B Part A Determine the magnitude of the moment of this force along the hinged axis of the door. Express your answer to three significant figures and include the appropriate units. M₂ = Submit μA Value Units My Answers Give Up Provide Feedback Continue

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 20-lb force is applied to the control rod AB as shown. Knowing thatthe length of the rod is 9 in. and that α = 25°, determine the moment of the forceabout Point B by resolving the force into horizontal and vertical components.EXPRESS YOUR ANSWER UP TO 3 DECIMAL PLACES
Determinethe magnitude (lb) of the horizontal component of force at point C if P = 154.5 lb, x = 14.5 in, y = 6.8 in, and z = 7.3 in. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction : use L if to the left or R if to the right.
Use THREE MOMENT EQUATION MET determine the member end moments of the beam of the rectangular cross section shown in Figure 11.10a. Assume that support B settles 2 cm. The modulus of elasticity and the moment of inertia of the beam are E = 210,000 N/mm2 and 4.8 × 104 mm,4 respectively. Hint final answer: MAB= 0 MBA= 165.5127 kn.m MBC= -165.5127 kn.m MCB= 52.2604 kn.m
Determine the value of EIv (in lb ft3 )at midspan for the beam loaded by two concentrated forces if P = 241lb and Q = 73lb. NOTE: PLEASE ANSWER IT CORRECTLY. IF YOU ARE NOT SURE ABOUT THE ANSWER, PLEASE SKIP THE QUESTIONPLEASE BOX THE FINAL ANSWER(S)THANK YOU!
A steel tape with a cross-sectional area of 0.03 sq. cm is 50.00 m long under a pull of 5 kg when supported throughout its length. It measures a line 857.63 m long under a steady pull of 10 kg. Assuming E = 2.0 x 10 to the power of 6 kg/sq. cm, what is the elongation of the tape due to the increase in tension? a. 0.0250 m b. 0.0024 m c. 0.2500 m d. 0.0042 mShow solution please
a ,b, c and d are answered 2) the steel weights 18.61 tons 3) 18.61 * $1500= $27920 4) ??? I don’t understand 4 please.
ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITET THE COMPLETE SOLUTIONS COMPLETELY AND LEGIBLY. ANSWER IN 3 DECIMAL PLACES.) A force F passing through C causes a clockwise moment of 149 lb-ft about A and a clockwise moment of 87 lb-ft about B. Determine the value of x (ft) . Round off only on the final answer expressed in 3 decimal places.
A 50 m steel tape measured 50.0250 m when standardized fully supported under a 90-newton pull at a temperature of 20°C. The tape weighed 12N and had a cross-sectional area of 0.028 cm^2. What is the true length of the recorded distance AB for the following condition? (K= 0.0000116/°C, modulus of Elasticity =2.1x10^7).Recorded distance: 215.095 mAverage temperature: 12°CMeans of support: SuspendedTension: 120 NElevation difference per 100 m: 2.5mRound off the final answers to the nearest hundred thousandths (five decimal places) and indicate if the answer is positive or negative. 1. Determine the temperature correction for the entire length of the distance measured. 2. Give the correction for the absolute length of the tape, accounting the full length it measured. 3. Determine the sag correction for one tape length. 4. Determine the pull correction for the entire length of the distance measured. 5. Compute for the slope correction for the entire length of the distance measured.
Rod OA rotates about O in a horizontal plane. The motion of the 0.5-lb collar B is defined by the relations r= 10 + 6 cost and 0=(4-8), where r is expressed in inches, r in seconds, and 8 in radians. Determine the radial and transverse components of the force exerted on the collar when (a)1=0, (b) t=0.5s.
Flat plate of area 106 mm2 is pulled with a speed of 0.4 m/s. relative to another plate located at a distance of 0.1 mm from d. Find force and power (consider Dynamic viscosity = 2 poise)
The figure below shows a rectangular gate holding sea water behind it (sg = 1.08). If the water is 18.00 ft deep, (Part a) compute the magnitude (in lb) and (Part b) determine the location of the resultant force on the gate. (Report the location to three decimal places).
Consider the frame shown in (Figure 1). Suppose that F1 = 3.5 kN. a) Determine the x and y components of the force that the pin at B exerts on the frame using scalar notation. b) Determine the x and y components of the force that the pin at A exerts on the frame using scalar notation. Express your answers in kilonewtons to three significant figures. Enter your answers separated by a comma.