PROBLEM 5: A turbine, located at an elevation 255 m below that of the water surface at intake, carries a flow of 3.5 m^3/s. The head loss in the pipeline leading to it is 10 m. Find the horsepower delivered by the turbine if its efficiency is 92%. (746 watts = 1 HP). Illustrate the problem and show your complete solution.

PROBLEM 5: A turbine, located at an elevation 255 m below that of the water surface at intake, carries a flow of 3.5 m^3/s. The head loss in the pipeline leading to it is 10 m. Find the horsepower delivered by the turbine if its efficiency is 92%. (746 watts = 1 HP). Illustrate the problem and show your complete solution.

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter13: Tidal Energy

Section: Chapter Questions

Problem 17P

See similar textbooks

Similar questions

A conical tank 4.5m on top and 4,7m tall has a 60mm diameter orifice at its bottom for its outlet. Assume C = 0.63. The tank is filled with 7000 liters of water. What is the depth of the water in the tank in meters? How long will it take to drain the content of the tank in minutes? show solution and diagram
Q_3/Figure shows a pump employed for lifting water from a sump. If it is required to pump (60 liters/sec.) of water through a (0.1 m) diameter pipe from the sump to a point (10 m) above, Determine the power required. Also determine pressure intensities at Land M. Assume an overall efficiency of (70 %). Neglect All Losses
Water is flowing in a 90° triangular channel at a depth of 39 cm. A hydraulic jump occurs. The depth after the jump is 126 cm. a. What is the discharge?b. What is the decrease in specific energy caused by the jump?c. What is the head loss in kW?
Water leaving the nozzle at a velocity of 4350 m/min with a volume flow rate of 0.736 m³ . if the density of water is 0.000997 kg/cm³ . How will you determine the potential for power generation in a hydraulic turbine .
A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of—assume values with decimals between 3 to 4 m per second—enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack. Please answer this with complete solutions and figure. Thanks
b) Water flows from a large reservoir through a pipe system which consists of 200 mm diameter ofpipe and 50 mm diameter of nozzle as shown in Figure 3. By neglecting all energy losses, calculate;(ii) Velocity and pressure at A
An open cylindrical tank 800mm in diameter and 2000mm high contains water to a depth of 1.6m. It is rotated about its vertical axis at 13 rad/s. How many liters of water are spilled? Use density of water as 1000kg/m3 and specific weight as 9.81kN/m3
A horizontal pipe carries cooling water from a reservoir as shown in the following figure. If the pipe diameter is 20 cm, the flow rate is 0.06 m3/s, what is the pressure at L= 2000 m? Calculate head loss as hL = 0.015(L/D)(V 2/2g)
An agricultural land install a pump with a 218mm diameter suction pipe and a 200mm diameter discharge pipe. Respectively each pressure reads 1.12 bars and 0.96 bars. The water flow measured 12.500 liters/min.at normal temperature. Calculate the following: 1. Head at the discharge side, m 2. Velocity Head. m 3. Total Head of the pump, m
A pump pumps water from one tank (open to atmosphere) to another tank (open to atmosphere) at a height of 25 m. A pipe with a diameter of 50 mm and a length of 100 m (e=1.5 mm) is used in the system. Since the variation of the pump's head with the flow rate is given as H= 50-20000Q^2, calculate the water flow through the pipe by ignoring the local losses (ρ=1000 kg/m^3, μ= 0.001 N.s/m)
A pump system is used to move water at a flow rate of 30 L/s from a lower to a higher reservoir in a city with an elevation of 1000 m above sea level. The system is shown schematically in the figure below, with ∆?=30 m. Both the suction and delivery pipes have a diameter of 150 mm and an absolute roughness of 0.3 mm. The lengths of the suction and delivery pipes are 6 and 500 m respectively. Ignore local losses and assume a temperature of 15 °C. a)Develop a mathematical expression for the system curve (i.e. the pumping head required as a function of the system flow rate) from basic principles. Name all mechanics principles implemented. b)Calculate the required pump working point. What is the flow regime of the pipe flow. c)What power does the pump add to the water in the system?
The water system in an urban area consists of an old 200 mm pipeline 750 m long which conveys water from a pump to a reservoir whose water surface elevation is 105 m higher than the pump. Water is pumped at a rate of 70li/sec. Determine the horsepower saved by replacing the old pipe with a new 25 cm pipe. Assuming f=0.033 and 0.022 for the old and new pipe respectively. Neglect other losses except frictional loss.