Problem 5: Consider the magnetic core shown in figure P-5. The depth of the core into the page is 5 cm. One coil has a 1000 turns and 1 A current, while the other coil has 2000 turns and 2 A current. The relative permeability of the core is 3000. Determine the flux density in the right, center, and left sections of the core. 1000 turns 10cm -20cm +10cm] Figure P-5 2000 turns 10cm 20cm 10cm -20cm-1 1++ 10cm

Problem 5: Consider the magnetic core shown in figure P-5. The depth of the core into the page is 5 cm. One coil has a 1000 turns and 1 A current, while the other coil has 2000 turns and 2 A current. The relative permeability of the core is 3000. Determine the flux density in the right, center, and left sections of the core. 1000 turns 10cm -20cm +10cm] Figure P-5 2000 turns 10cm 20cm 10cm -20cm-1 1++ 10cm

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.1MCQ: The Ohms law for the magnetic circuit states that the net magnetomotive force (mmf) equals the...

See similar textbooks

Similar questions

A ferromagnetic core with a relative permeability of 1500 is shown in the following figure. The depth of the core is 5 cm. Because of fringing effects, the effective area of the air gaps is 5 percent larger than their physical size. If there are 300 turns in the coil wrapped around the center leg of the core, and if the current in the coil is 1.25 A, find the magnetic flux and the field density in all three legs of the core, as well as the magnetic flux and flux density in the two air gaps.
A core with three legs is shown in the figure below. Its depth is 5 cm, and there are 400 turns on the centre leg. The remaining dimensions are shown in the figure. The core is composed of steel having the magnetization curve is also given below. Answer the following questions about this core: 1. What current is required to produce a flux density of 0.5 T in the central leg of the core? 2. What current is required to produce a flux density of 1.0 T in the central leg of the core? Is it twice the current in part (a)? 3. What are the reluctances of the central and right legs of the core under the conditions in part (a)? 4. What are the reluctances of the central and right legs of the core under the conditions in part (b)? 5. What conclusion can you make about reluctances in real magnetic cores?
Q1. A core with three legs is shown in Figure. Its depth is 5 cm, and there are 100 turns on the leftmost leg. The relative permeability of the core can be assumed to be 2000 and constant. What flux exists in each of the three legs of the core? What is the flux density in each of the legs? Assume a 5% increase in the effective area of the air gap due to fringing effects.
Below you can find a ferromagnetic core and its magnetization curve. If i1=0.4 A and i2= 0.9A, find magnetic flux in the core and the relative permeability under these conditions.
A ferromagnetic core is shown in Figure 1. The relative permeability of the core isassumed to be 2500 and constant. There is a 5% increase in the effective area ofthe air gap due to fringing effects. The depth of the core is given as 5 cm. The Rtotal is found to be 226.192k At/Wb
An iron-cored choke is designed to have an inductance of 12.5 H when operating at a flux density 3 T, the corresponding relative permeability of iron core is 1500. Determine the number of turns in the winding, given that the magnetic flux path has a mean length of 20 cm in the iron core and 2 mm in air-gap that its cross-section is 15 cm2. * ROUNDING OFF is ALLOWED only in the final answers expressed up to FIVE (5) DECIMALPLACES.
For the magnetic circuit shown in the figure, the iron core with N = 500 turns -Magnetic permeability is 200. its average length is 40 cm -The diameter of the cross-sectional area is 1 cm. Find the current that must pass through the winding to produce 0.5 mWb of flux in a 1mm air-gap magnetic circuit?
1) A ferromagnetic core is shown in Figure 1. The relative permeability of the core isassumed to be 2500 and constant. There is a 5% increase in the effective area ofthe air gap due to fringing effects. The depth of the core is given as 5 cm.a) Calculate the total reluctance, total, of the core
In the magnetic circuit in the figure, the relative with a magnetic permeability of 2000 the cross-sectional area of the core is constant and 1 [m2 ] is. middle arm (AB) Find the magnetic flux.
An ideal core (assume relative permability is infinity) with a crossectional area of 12 cm2is excited via10A current flowing through coil with 200 turns. On the one side of the coil, a 1 cm long paramagneticmaterial (µr=1) is placed. Calculate the magnetic field on paramagnetic material
Consider the magnetic circuit shown in Figure T14.4. The core has a relative permeability of 1500. a. Carefully estimate the flux density in the air gap. b. Determine the inductance of the coil.
A square magnetic core has a mean length of 43 cm and a cross-sectional area of120cm2. A coil of 200 turns of wire is wound around one of the columns of the core, thewhich is made of a material whose required magnetic field strength is H=115 Aturns/m. a) How much current is required to produce a flux of 0.012 Wb, in the core?b) What is the relative permeability of the core for that current?c) What is the reluctance?