PROBLEM: A 9-Storey building is supported by a steel braced frame on a certain location having the ff. data available: Z= 0.4, I = 1.0, Soil Profile Type = SD, R = 6, Ct = 0.035, Seismic Source Type A, and d= 4.3km. 1. Solve for the design base shear. 2. Solve for the floor shears. 3. Draw and label all the forces in the building.

PROBLEM: A 9-Storey building is supported by a steel braced frame on a certain location having the ff. data available: Z= 0.4, I = 1.0, Soil Profile Type = SD, R = 6, Ct = 0.035, Seismic Source Type A, and d= 4.3km. 1. Solve for the design base shear. 2. Solve for the floor shears. 3. Draw and label all the forces in the building.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.2P

See similar textbooks

Similar questions

The backfill behind the concrete retaining wall weighs 110 pcf and the angle of internal friction is 30 degrees. The live load surcharge on the surface of horizontal backfill is 200 psf. a. Determine the total active force acting on the wall per unit width. b. Find the factor of safety against overturning.
The section of the masonry dam is shown in Figure3a. If the uplift pressure varies uniformly from fullhydrostatic at the heel to full hydrostatic at the toe,but acts only over 2/3 of the area of the base, find(a) the location of the resultant; (b) the factor ofsafety against overturning; and (c) the factor ofsafety against sliding if the coefficient of frictionbetween base and foundation is 0.60. Unit weight of concrete and masonry is 23.54 kN/m3for all the problems NOTE: CLEAR HANDWRITTEN SOLUTION
Determine the allowable shear stress if W= 33,813lb.
e. Location of the total earth thrust from the base of wall (in meter) ya = f. Minimum width B (in meter) of wall to be safe against sliding if the mobilized friction angle at the base of wall is 25o and factor of safety against sliding is 1.5 (minimum). Consider 24 kN/m3 as the unit weight of concrete. B = Thankyou please
A building wall consists of exterior stud walls with brick veneer and 13 mm fiberboard on one side. If the wall is 4 m high, determine the load in kN/m that it exerts on the floor. From Minimum Design Dead load, For stud wall with brick veneer, w = 2.30 kN/m^2 and for fiber board, w = 0.04 kN/m^2.
A building wall consists of exterior stud walls with brick veneer and 13 mm fiberboard on one side. If the wall is 4 m high, determine the load in kN/m that it exerts on the floor.
4. The backfill behind the concrete retaining wall weighs 100pcf with an internal friction of 25º. The surcharge load on the surface of the horizontal backfill is 200psf. a. Calculate its total active force acting on the wall per unit widthb. Determine its factor of safety against overturning.
Determine the horizontal shearing stress at 95 mm above the Neutral Axis.
In the figure shows a load diagram acting on the retaining wall. If the resultant is located at the mid-height of the wall, determine the following.
A wall footing 1 m wide carries a uniform load of 300 kN/m of wall length. Soil weights 16 kN/m^3.Using the influence chart, compute the total vertical increment of the loads at a depth of 3 m from the edge of the strip in kN/m. a. 48 b. 60 c. 156 d. 108
A 5-m propped beam carries a uniformly distributed load equal to 45 kN/m applied throughout the beam. If the reaction at the roller is 84.375 kN, what is the maximum flexural shear stress if the beam has a rectangular cross-section with b = 300 mm and h = 600 mm? (in MPa)
Calculate the width of the concrete wall that is necessary to prevent the wall from sliding and the horizontal reaction acting on the system, Rx. The unit weight of the concrete is 23.6 kN/m^3 and the coefficient of friction between the base of the wall and the foundation soil is 0.42. Use 1.5 as the factor of safety against sliding. Will it also be safe from over turning?