Problem I. A homogeneous, graded shaft with circular cross section is clamped at both ends and loaded by the torque Mo = 100 kN m Use a = 2 m, b = 3 m, ri = 25 mm, r2 = 40 mm, and G = 77.2 GPa. a) Compute the torques at the support positions A and B. b) Compute the angle of twist at the point where Mo is applied. 1 2r1 2r2 A Мо a

Problem I. A homogeneous, graded shaft with circular cross section is clamped at both ends and loaded by the torque Mo = 100 kN m Use a = 2 m, b = 3 m, ri = 25 mm, r2 = 40 mm, and G = 77.2 GPa. a) Compute the torques at the support positions A and B. b) Compute the angle of twist at the point where Mo is applied. 1 2r1 2r2 A Мо a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?
The compound shaft shown consists of a solid shaft AB made ofbronze [G = 40 GPa], and a solid shaft BC made of steel [G = 85 GPa].The compound shaft is subjected to torques TB = 700 N.m at point B,and TC = 200 N.m at point C, acting in opposite directions.[LAB = 900 mm, LBC = 1200 mm, dAB = 35 mm, dBC = 25 mm]Determine (a) the internal torques in shafts AB and BC, (b) the shearstresses in shafts AB and BC, and (c) the angle of twist at point C.
The 600mm diameter steel shaft is subjected to the torques shown. Determine torsion at each section. Assume G = 75 GPa. P=74 1.5P= 1.5(74) = 111 kNm 3P= 3(74)= 222kNm
Prob. 2. A 1,000-ton train is accelerated at a constant rate up a 2% grade. The train resistance is constant at 10lb/ton. The velocity increases from 20mi/h to 40mi/h in a distance of 2,000ft Question#1 From Prob. 2, determine the constant drawbar pull exerted by the locomotive
Refer to the beam loaded as shown. (a)What is the Value of horizontal reaction at the fixed support?(b)What is the value of resulting couple at A?
The 600mm diameter steel shaft is subjected to the torques shown. Determine torsion at eachsection. Assume G = 75 GPa. P= 81
An shaft consist of a hollow shaft 3m long, with an outside diameter of 200mm and an inside diameter of 150mm, rigidly attached to a solid shaft 2m long with a diameter of 150mm. Determine the maximum torque which can be applied without exceeding a shearing stress of 70 MPa or a twist of 4.3degree in the 5m length. Use G=83 GPa.
The solid steel shaft carries the torques T1= 1200 Nm and T2=750 N m. Using L1=L2=2.5 m and G = 83 GPa, determine: a. draw a diagram using a double headed arrows showing the torque in each segment b. determine the shear stresses in each segment and the angle of rotation of the free end if the diameter is 100 mm. c. the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 4^0.
THE ANSWER MUST BE IN FOUR DECIMAL PLACES the steef shaft shown in figure rotates at 4Hz with 35 KW taken off at A, 20 kW removed at B and 55 kW applied at C. Using G=83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C
A flat belt connects pulley A to pulley B. The coefficients of friction are ms = 0.25 and mk = 0.20 between both pulleys and the belt. Knowing that the maximum allowable tension in the belt is 600 N, determine the largest torque (in N.m) which can be exerted by the belt on pulley A.
If the coefficient of static friction at contact points A and B is μs = 0.3, determine the maximum force P that can be applied without causing the 100-kg spool to move.
Determine the Force Frequired to hold the bar AB in a horizontal position on the smooth inclines shown in figure below. Also determine the reactions at A and B 1.2m, 4.2m, 0.6m A 60 degrees and 45 degrees B 90N