Problem Statement Based on Problem 4-151 from the textbook. The pipe assembly is subjected to the action of a wrench at B and a couple at A. Simplify this system to a resultant wrench and specify the locaiton of the wrench along the axis of pipe CD, measured from point C. F=31.7N 0.6 m, 0.8 m 0.25 m (-40) N 0.25 m -Fi 63m 1-60k) N 0.3 m 0.7 m Fi 0.5m D

Problem Statement Based on Problem 4-151 from the textbook. The pipe assembly is subjected to the action of a wrench at B and a couple at A. Simplify this system to a resultant wrench and specify the locaiton of the wrench along the axis of pipe CD, measured from point C. F=31.7N 0.6 m, 0.8 m 0.25 m (-40) N 0.25 m -Fi 63m 1-60k) N 0.3 m 0.7 m Fi 0.5m D

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.153P: Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Draw a free-body diagram for this system.
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
The uniform bar AB weighing 240 lb is mounted as shown in the figure upon a carriage weighing 480 lb. The center of gravity of the carriage is at C midway between the wheels. If P = 180 lb and there is no frictional resistance at the wheels, find the value of R1
Draw the Free Body Diagram and solve the problem
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
PROBLEM 4: The boom OC is subjected to tension forces at A and C. It is known that the tension in A is 26 kN and at C is 12 kN. Unit vector CE. (ANSWER: -0.38i-0.87j+0.32k) Tension at A. (ANSWER: 13.20i-15.8j+15.8k kN VECTOR COMPONENT FORM) Moment about O due to the given forces. (ANSWER: 78.71i+0j+3.2k kN VECTOR COMPONENT FORM)
I need to draw a free body diagram and the solution L=10m
#1: A moment Macts on the brake drum shown. The radius of the drum is 150 mm. If mu = 0.35 between the drum and belt, calculate the larger tensile force exerted by the belt. Also, determine the magnitude of the braking moment M due to the vertical force P = 120 N.
Rigid arm AB is subject to a downward force F=270 lbf. It is supported by asquare shaft journal bearing at A and a cable BC.A. Draw a clear and large free-body diagram (FBD) to show all reaction components on AB. Ifany are not engaged, cross them out and add the note “N.E.” for “Not Engaged.” You do NOTneed to set up any equations or solve for any of the reactions.B. Find the unit vector for cable BC.
3 include free body diagram
Find the support reacions and joint force of the construction shown on the figure, if; P=12 kN q=9 kN/m M=12 kN and L=2 m