Problems in SI UnitsProblem 15.15 Determine the required spacing of #13 closed O stirrups at a distance d from the face of the support for thebeam shown assuming that the torsion decreases uniformly from the beam end to the beam centerline. The member issubjected to a 34-kN•m service dead load torsion and a 40-KN•M service line load torsion at the face of the support,f, = 420 MPa, f. = 24 MPa, and clear cover = 40 mm. (Ans. 175 mm)D = 10 kN/m (including beam weight)L = 25 kN/m700 mm5 #327 m450 mm→

Answered: Image /qna-images/answer/d4ab6f1c-cdb3-4be7-b569-06c148418bb6.jpg

Answered: Determine the required spacing of #13…

Engineering

Civil Engineering

Determine the required spacing of #13 closed stirrups at a distance d from the face of the support

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.50 in. and a wall thickness of 0.201 in. is fastened to a solid 2.00-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=19 kips, Q=13 kips, L1=7 ft, L2=9 ft, and L3=9 ft. Determine(a) the stresses in all parts of the axial structure.(b) the deflections of joints B and C.
Problem 4. A reinforced concrete beam having a simple span of 8m is reinforced for tension with 25mm dia bars (As = 1963 mm2). The beam has a width of 350mm and an effective depth of 690 mm. Use f'c = 20.7 MPa, fy = 414 MPa. a. Determine the location of the neutral axis measured from the top outermost compression fiber of the section. Ans.: Blank 1 mm b. Determine the ultimate moment capacity of the beam. Ans.: Blank 1 kN.m. c. Determine the safe uniform live load (in kN/m) that the beam could carry. Assuming weight of concrete is 24 kN/cu.m. Ans.: Blank 1 kN/m
line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 200 C under a 50 N pull supported at both ends. During measurement, the ttemperature is 50C and the tape is suspended under a 75 N pull. The line is measured on a 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3 mm2 and the coefficient of linear expansion is 0.000016 m/0C. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance.
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 67 GPa. The steel rod has a diameter of 18 mm and an elastic modulus of E = 180 GPa. Assume a = 3.1 m, b = 1.3 m, and c = 1.3 m. What is the magnitude of load P that is necessary to displace point A 10 mm to the left?
A W 10 x 30 is used as a beam to support a concrete floor system. The floor is to carry a total load of 4.2 kPa. The beam is simply supported over a span of 8.4 m. The properties of the section are as follows: Depth = 254 mm Thickness of web = 19.2 mm Moment of Inertia = 98 x 106 mm4 Section modulus = 530 x 103 mm3 Weight = 44.86 k9/m Assume the beam is laterally supported over its length and that the allowable stress in bending is 0.66 Fy and in shear on gross section is 0.4Fy . Use A36 steel with Fy = 250 MPa. Determine the center-to-center spacing of the beams without exceeding the allowable shear stress. Determine the center-to-center spacing of the beams without exceeding the allowable bending stress. Which will be the center-to-center spacing of the beams to consider?
The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A and C are stress-free. Ifa20-kip load is applied, determine the vertical displacement in the barat ?and C that will cause a stress in the rod at C to be 50ksi. Indicate the direction of movement. Use E=29x106psi for steel.(Provide FBD and movement diagramin your computation).
A simply supported beam has a maximum moment equal to 20 KN.m. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. What is the actual bending stress of the beam in MPa? Blank 1 (use two decimal places, no need for unit)\\ with complete solution
A single-span beam having unsupported length of 8m. has a cross section of 200mm x 350mm. (use nominal dimension). It carries a uniformly distributed load “W” kN/m throughout its span. Allowable bending stress is Fb=9.6 MPa and a modulus of elasticity of 13800 MPa. From the table, the effective length Le=1.92 Lu where Lu=unsupported length of beam. a. Compute the allowable bending stress with the size factor adjustment in MPA b. Compute the allowable bending stress with lateral stability adjustment in MPa c. Compute the safe uniform load “W” that the beam could carry in KN/m. (choose the smallest of prob. a and b.) use M=wl^2 / 8
Determine the x, y, z components of internal loading at a section passing through point B in the pipe assembly. Neglect the weight of the pipe. TakeF1 = {100i - 200j - 300k} N and F2 = {100i + 500j}N.
Calculate x if point B contacted with the square support? (Erod CD=200GPa; AB is a rigid bar without deformation)
What is the internal force in member AB? A. 750 N , T B. 450 N , T C. 750 N , C D. 450 N , CSHOW SOLUTIONS
The compound shaft shown is attached to a rigid supports. For bronze segment AB, the diameter is 75 mm, maximum shearing stress is 60 MPa, and G = 35 GN/m^2. For steel segment BC, the diameter is 50 mm, maximum shearing stress is 80 MPa, and G = 83 GN/m^2.1. Which of the following most nearly gives the ratio torque carried by bronze to torque carried by steel? a. 1.2b. 1.8c. 1.6d. 2.02. Which of the following most nearly gives the torque carried by the bronze in kN.m?a. 4.98b. 9.15c. 6.53d. 3.143. Which of the following most nearly gives the maximum torque T than can be applied in kN.m? a. 6.4b. 5.1c. 4.3d. 7.8