Please explain Pump delivers 0.05 m/s flow of 40°C water, and the intake pipe L = 4m & D = 20 cm. The pump intake is located 10 m above the water surface level in thereservoir. How much lowering of the pump elevation will avoid the cavitation.Given: f= 0.018, Ke = 0.1, K, = 0.210 mPar = 101.3 kPa absYH.0x 40°c = 9.732 kN/m³Pvap at 40°C= 7.38 kPa abs= 7.38-101.3 = -93.92 kPa gageO Lowering of the pump needed to avoid cavitation = 7.44 mO Lowering of the pump needed to avoid cavitation = 9.65 mO Lowering of the pump needed to avoid cavitation = 0.56 mO None of the answers are correct.

Pump delivers 0.05 m/s flow of 40°C water, and the intake pipe L = 4m & D = 20 cm. The pump intake is located 10 m above the water surface level in the reservoir. How much lowering of the pump elevation will avoid the cavitation. Given: f = 0.018, K̟ = 0.1, K, = 0.2 10 m Pan = 101.3 kPa abs 740x 40c = 9.732 kN/m³ = 7.38 kPa abs Prap at 40°C = 7.38-101.3 = -93.92 kPa gage O Lowering of the pump needed to avoid cavitation = 7.44 m O Lowering of the pump needed to avoid cavitation = 9.65 m O Lowering of the pump needed to avoid cavitation = 0.56 m O None of the answers are correct.

Pump delivers 0.05 m/s flow of 40°C water, and the intake pipe L = 4m & D = 20 cm. The pump intake is located 10 m above the water surface level in the reservoir. How much lowering of the pump elevation will avoid the cavitation. Given: f = 0.018, K̟ = 0.1, K, = 0.2 10 m Pan = 101.3 kPa abs 740x 40c = 9.732 kN/m³ = 7.38 kPa abs Prap at 40°C = 7.38-101.3 = -93.92 kPa gage O Lowering of the pump needed to avoid cavitation = 7.44 m O Lowering of the pump needed to avoid cavitation = 9.65 m O Lowering of the pump needed to avoid cavitation = 0.56 m O None of the answers are correct.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The siphon in Fig. is used to draw water from the large open tank. If the absolute vapor pressure for the water is p = 0.91 kPa, determine the shortest drop length L of the 40 mm diameter tube that will cause cavitation in the tube. Draw the energy and hydraulic grade lines for the tube.
Water at 15°C (? = 999.1 kg/m3 and ? = 1.138 × 10−3 kg/m·s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
Two water reservoirs of height h1 = 60 m and h2 = 30 m are connected by a pipe that is 0.35 m in diameter. The exit of the pipe is submerged at a distance of 8 m from the (2nd) reservoir surface. a. Provide a diagram b. Determine the flow rate through the pipe if the pipe is 80 m long and the (Fanning) friction factor f' = 0.004. The pipe inlet is set flush with the wall. c. If the relative roughness ε/D = 0.004, determine the friction factor and flow rate.
A 300 mm cast-iron pipe is discharge 120 lit/sec. At a point 200 m from the reservoir the center of the pipe is 30 m below the reservoir surface. What is the pressure in kPa to be exerted there? Assume f= 0.02
Water is pumped from the reservoir with a surface elevation of 200 m across the valley to another reservoir of surface elevation 216 m through a pipe line of 1300 m long and 30 cm diameter if during pumping the pressure is 5.6 kg/cm2 at a point half way along the pipe and at an elevation of 168 m. Compute the discharge and power of the pump taking friction factor as 0.02 neglect minor losses.
A horizontal pipe of 150 mm diameter for the initial 30 m and 75 mm dimeter for the remaining 10 m is connected to a water tank. The height of waler in tank is 15 m above the centre line of the pipe. Find out the flow rate through the pipe, taking all losses into the account. Consider the reduction in diameter of the pipe as sudden coefficient of friction for the pipe is 0.008.
A flow of water of 100 lt/sec flowing through rectangular tube of width 600 mm and having adjustable bottom slope with C = 56. Find the bottom slope required for uniform flow of depth 300 mm. Also, determine the convience of fume.
A 1.20 m-diameter(internal)horizontal steel penstock conveys water at the rate of3.6 m3/s. The thickness of the pipe wall is 25 mm. Thebulk modulus of elasticity of water is 2.2 GPa. The pipehas length of 1000 m and the friction factor is 0.020. Thewater surface elevation in the reservoir is 60 m. If theflow is stopped completely by closing the valve in 2sec, determine the following:(a) the maximum water hammer pressure that candevelop.(b) the maximum pressure at the valve.(c) the elongation of the pipe in mm (△=ForcexL/AE) foran almost instantaneous closure.
. Water flows in a new 20cm diameter, 300m long ductile iron pipe between reservoirs A and B,as shown in Figure P4.2.1. The pipe is elevated at S, which is 150m downstream from reservoir A.The water surface difference between the two reservoirs is 25 m. Determine the head that should beprovided by a booster pump 100 m downstream from reservoir A if Δs is 3 m and the pressure headat that location must be kept above -6m because of cavitation concerns. Sketch the EGL and theHGL for the pipeline. friction factor f as 18
Estimate the equivalent hydraulic conductivity for flow in the horizontal direction. Also calculate the ratio of kv(eq)/kH(eq). Suppose that k1 = 15 x10^-4 cm/s, k2= 5.0x10^-4 cm/s, k3= 3.0 x10^-4 cm/s, k4= 2.0 x10^-4 cm/s, H1= 1.0 m, H2 = 2.0 m, H3 =1.5 m, H4 =1.0m. kH(eq) = kV(eq)/kH(eq)=
An engineer is hired to design a swimming pool 15m long by 6m wide by 2m deep. For water supply, he decideds to lay 600m of 5cm pipe with f=0.020 from a nearby main to the pool. The pipe will discharge freely into the pool during the entire filling process. The average pressure at the water main is 550kpa and the difference in elevation between the two ends of the pipe is 10m, with the discharge end higher than the intake end. Assuming that 10% of the loss in the pipeline are due to transitions, fittings and valves, how long would it take to fill the swimming pool?
Two reservoirs are connected by three pipes. laid in parallel. The pipes diameters are respectively 10cm, 20cm and 30cm and they are of the some length. If discharge through 10cm pipe is 0.1 m3/s, calculate the discharge through the larger pipes. Assume the friction coefficient ‘f’ to be same for the pipes.