Question number 2*Decent handwriting pls* Q 2A 3-ph,4 -pole, 50 Hz synchronousmachine has the following data as given below:Kw of Rotor =0.976; air gap 1.5 mm; meanair gap diameter 29 cm ;Axial length 35 cm; Rotor winding turns 746,Stator winding SPP= 4, Conductor per slot 20;Stator current 25A. The machine is being used inmotoring mode with Br = 1.6T. Determine(i)Peak rotor AT (ii) Max Torque (iii)electrical output at max. torque.

Given that 3ϕ,4 pole,50HzKw=0.976Air gap=1.5mmMean air gap=29cmAxial length=35cmRoator winding…

Answered: Q 2 A 3-ph,4 -pole, 50 Hz synchronous…

Q 2 A 3-ph,4 -pole, 50 Hz synchronous machine has the following data as given below Kw of Rotor =0.976; air gap 1.5 mm; m. air gap diameter 29 cm ; Axial length 35 cm; Rotor winding turns 746,

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

21 A 25 kW, 240 V self excited dc shunt generator has a field circuit resistance of 62.5 Ω, and an armature resistance of 0.05 Ω. When delivering rated current at rated speed and voltage, calculate % Efficiency when rotational losses are 1200W, and iron losses are 600W. Note that Copper losses must be calculated too. No Units! Please answer in typing format please ASAP for
A3-phase, 5.5kW, 440V, 50Hz, cylindrical rotor S.M has synchronous reactance of (0+j2) Ω/phase. When it is delivering its rated output the motor efficiency is 85% and load angle is 20º. Find the excitation voltage, armature current and the power factor
handwritten only. A 25 kW, 240 V self excited dc shunt generator has a field circuit resistance of 62.5 Ω, and an armature resistance of 0.05 Ω. When delivering rated current at rated speed and voltage, calculate Ea No Units!
3-phase, 50 Hz, 4-pole, 220 V, 10A ASM has an ASM 0.85 back power coefficient. stator copper losses are 500 W and rotor copper losses are 200 W. Friction and wind losses 100 W, core losses 300 W and stray load losses 50W. According to this; a. Air gap strength b. Mechanical strength produced c. Output power in horsepower D. Yield e. Slipping f. Working Speed g. Torque Produced h. Output Torque i. By specifying the asynchronous Motor power flow diagram from input to outputby drawing?
Q23) A shunt generator supplies a 20KW load at 200V through cables of resistance, R = 100mΩ. If the field winding resistance ,Rf=50Ω and the armature resistance, Ra=40mΩ, i) Estimate terminal voltage across the load. ii) Calculate the emf generated in the armature.
A 250 V shunt generator has a full load armature current of 40 A, under these conditions the losses are: FW = 200 watts, shunt field = 100 watts, core = 260 watts, brush contact = 120 watts, armature copper = 400 watts. For operation at maximum efficiency, when the constant losses are equal to those losses that vary as the square of the load, calculate the maximum efficiency.
The open-circuit characteristic of a shunt generator when driven at normal speed is as follows :Field current : 0.5 1.0 1.5 2.0 2.5 3.0 3.5 AO.C. volts : 54 107 152 185 210 230 240 VThe resistance of armature circuit is 0.1 Ω. Due to armature reaction the effective field current is givenby the relation Ish (eff.) = Ish − 0.003 Ia. Find the shunt field circuit resistance that will give a terminal voltageof 220 V with normal speed (a) on open circuit (b) at a load current of 100 A. Also find (c) number of seriesturns for level compounding at 220 V with 100 A armature current ; take number of shunt turns per pole as1200 and (d) No. of series turns for over-compounding giving a terminal voltage of 220 V at no-load and230 V with 100 A armature current.
A 110V shunt generator has a full load current of 100A, shunt field resistance of 55 ohms and constant losses of 500W. If full load efficiency is 88%, find the armature resistance. Assuming voltage to be constant at 110V, calculate the efficiency at half load. Find the load current.
A 240 V, Short – Shunt DC Generator supplies a load current of 60 A. The armature circuit resistance is 0.10 Ohms and shunt-field circuit resistance is 120 Ohms. The series-field resistance is 0.08 Ohms. Calculate The developed Power The percentage voltage regulation. Draw the power flow graph, showing the various losses as well the input, developed, and output power values. P rotational = 500W
Q. A 3-phase, star connected, 10 kVA, 400 V, salient pole alternator with direct and quadrature axis reactances of 15 ohm and 8 ohm respectively, delivers full-load current at 0.8 power factor lagging.Neglect the armature resistance. Solve this question to chose the correct answer for the following: The direct axis and quadrature axis components of armature current are ........ and ......... respectively ?
The figure shows the excitation curve (including residual voltage) of a 170 kW, 250 V DC shunt generator at rated speed of 850 rpm. The generator has negligible (0 W) armature resistance and a shunt field coil resistance of 50 W. The variable Field Control Rheostat in series with the shunt field coil has variable resistance in the range of 0 – 25 W. Explain your reasoning for choosing the following answers. (a) What is the approximate value induced EMF( Eo) at a field current of 5.6 A and rotor speed of 630 rpm? 375 V 335 V 300 V 275 V 200 V (b) What is the field current when the induced emf is 328 V and the rotor speed is 935 rpm? 4 A 4 A 1 A 8 A 0 A (c) What is the rheostat resistance settings when the induced voltage is 300 V and the generator is turning at 120% rated speed? 65 Ω 47 Ω 32 Ω 25 Ω 2.22 Ω
The open-circuit characteristic of a shunt generator when driven at normal speed is as;Field current (A)0.51.01.52.02.53.03.5O.C. volts (V)54107152185210230240The resistance of armature circuit is 0.1 Ω. Due to armature reaction the effective field current is given by the relation Ish (eff.) = Ish − 0.003 Ia. Find the shunt field circuit resistance that will give a terminal voltage of 220 V with normal speed (a) on open circuit (b) at a load current of 100 A. Also find (c) number of series turns for level compounding at 220 V with 100 A armature current; take number of shunts turns per pole as 1200 and (d) No. of series turns for over-compounding giving a terminal voltage of 220 V at no-load and 230 V with 100 A armature current.