Q 2: A rod 10cm long, has its ends A and B kept at 50°C and 100°C,respectively, until steady state conditions prevail. The temperature ateach end is then suddenly reduced to 0°C and kept so. Find the funetionof distribution temperature along the rod?

Answered: Image /qna-images/answer/83043b9a-022a-4e30-ae14-4599503ea37f.jpg

Q 2: A rod 10cm long, has its ends A and B kept at 50°C and 100°C, respectively, until steady state conditions prevail. The temperature at cach end is then suddenly reduced to 0°C and kept so. Find the function of distribution temperature along the rod?

Q 2: A rod 10cm long, has its ends A and B kept at 50°C and 100°C, respectively, until steady state conditions prevail. The temperature at cach end is then suddenly reduced to 0°C and kept so. Find the function of distribution temperature along the rod?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.63P

See similar textbooks

Related questions

Q: 019 For the plane wall shown in the figure (plane wall with heat source, one dimension and steady…

Q: The ends A and B of a rod 10 cm long have their temperatures kept at 0°c and 20°c respectively,…

Q: a. A slab of thermal insulator is 100 cm² in cross section and 2 cm thick. Its thermal conductivity…

A: Given Cross-sectional area = 100 cm2 Thickness = 2 cm Thermal conductivity = 2.4 × 10-4 cal(s cm C)…

Q: A rod of length 1, initial temperature is acos(æ)cos TDC TDC , both ends are kept at zero degree,…

A: Given: L = 1 T0 = acos(πx)cos(12πx) Temperature at both ends = 0 To find : Temperature distribution

Q: Figure shows a device for compacting loose material such as powder. A hydraulic pressure p(t) is…

A: given data: mass(m)=80kg damping coefficient(c)=80N.s/m stiffnes(K)=200N/m area of piston(A)=0.1m2…

Q: The inner and outer radii of a hollow cylinder are 15 mm (r,) and 25 mm (r, ), respectively. The…

Q: A smi-infinite cylinder in a steady state with the environment of radius 3-units. If the surrounding…

A: Fourier's Law of conduction:The law states that the rate of heat transfer by conduction in a given…

Q: A certain material has a thickness of 30 cm and a thermal conductivity of 0.04 W/m- °C. At a…

A: given:Heat flow expression ,T=150x2-30x

Q: The composite wall of an oven consists of three materials, two of which are of known thermal…

Q: A large concrete slab 1 m thick has one dimensional temperature distribution: T = 4 – 10x + 20x2 +…

A: This is the case of unsteady heat conduction and no internal heat generation.

Q: 4. A metal bar of length 30 cm has an initial temperature distribution at (2x + 5)°C. Suddenly the…

A: Given: L= 30 cm ITD= (2x+5) oC Constant temperature= 80 oC

Q: The heat flow per unit length of a thick cylindrical pipe is 772 W per meter. The pipe has radii ri…

Q: Heat flows through the wall in the following figure from the warm inside T to the cooler outside T,…

A: Given data The thickness of the glass wall = t Thickness of brick wall = t2Thickness of wood wall =…

Q: Let an aluminum rod of length 20 cm be initially at the uniform temperature of 25° C. Suppose that…

A: Given: L - 20cm T0 - 25 C Tl = 0 C Tr = 60 C To find : Temperature distribution

Q: In steady state, the heat transfer coefficient "k" is L=0.5 m Left face temperature of infinitely…

A: Given data as per questionT=250°Ch=40W/mKL=0.5mk=10W/mkqu=5×104W/m3

Q: 2. Consider a node on the corner of a solid shown below. Using the energy balance approach, derive…

A: Given : To find : Temperature at node m,n,o

Q: derive an expression for the thermal conductivity k(x) for these conditions

A: Given: q= 6000 W A(x)=1-x T(x)=300(1-2x-x3) x=0 , 1 To determine: Expression of thermal conductivity

Q: Q10) A sphere of radius b, given temperature at the outer surface by cos² , find steady sate…

A: 1-D steady state heat equation in spherical coordinate is integrated to get the temperature…

Q: A rod 3 m long is heated from 10°C to 90°C. Find the expansion of rod. Take Young's modulus = 1.0 x…

A: Given data: Initial length of the rod (Li) = 3 m Initial temperature (Ti) = 10oC Final temperature…

Q: 1- A rod of length ` has its ends A and B kept at 0 •C and 120-C respectively until steady state…

Q: Find the steady-state temperature u(r,θ) in a quarter semi-circular plate of radius r=5 subject to…

A: Given that, ur,0=0 ⇒Θ0=0ur,π2=0 ⇒Θπ2=0We can solve BVP in ΘΘ"+λΘ=0For λ≠0,The general…

Q: For two dimension heat conduction in a plate as shown in figure 3, find the temperature distribution…

Q: In steady state condition, the lateral surfaces of the plate are insulated, and the bottom surface…

A: Fourier's Law of conduction: The law states that the rate of heat transfer by conduction in a given…

Q: Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you…

A: Given: d= 1 ft L= 6 ft surface temperature=78 F h=2 Btu/hr emissivity=0.9 To determine heat transfer…

Q: Assume steady-state, one-dimensional heat conduction through the symmetric shape shown in Figure 1.…

A: Given : Assume Stady state one dimentional heat conduction through the symmetric shape. Condition :…

Q: The initial condition inside the system is 550 ℃, if the required heat transfer is only 5% then what…

A: Let us consider the wall as our system.Given:Temperature inside system(Wall),T1=550οCOutside…

Q: Find the steady-state temperature distribution in a metalic plate 20 cm by 60 cm if the two adjacent…

A: Given: The area of plate, A = 20 cm x 60 cm The temperature of adjacent sides of plates, Ts = 200…

Q: A composite wall is made up of 10 cm of common brick against 15cm of concrete with 1.5 cm of plaster…

Q: A cylinder with a diameter of 46 mm is heated on one end, causing a temperature gradient of 240°C/m…

Q: Find the steady-state temperature distribution u in a semi-infinite solid cylinder (Fig. 2) of…

Q: A spherical steel tank (k = 15 W/m.°C, thickness=1.5 cm) tank of inner diameter 2.66 m contains ice…

A: Given:Thickness of steel, t=1.5 cm or 0.015 mk=15 W/mo Cinner diameter of the tank, di=2.66 mouter…

Q: The heat transfer across a 5” wall of firebrick is 500 W/m2. If the surface temperature on cold side…

A: Heat flux q = kA*dT/dx

Q: A room has a pine ceiling [ k = 0.12 W/(m•C°) ] that measures 3.0 m x 4.0 m x 2.0 cm. On a cold day,…

Q: Water at 100°C flows in a aluminum pipe with a distance 10m (0.1m inside diameter, 0.02m thick, k=…

Q: 4) Air is confined to a vertical cylinder with a 2 cm diameter and 1 meter length that is closed at…

A: Given d= 2cm, l= 1m Piston weight= 10 N considering ambient pressure as 1 atm P1=Po=1 atm= 101.325…

Q: inner radius ri, outer radius r0, thermal conductivity k, according to this for the thermal…

Q: Assume steady-state, one-dimensional heat conduction through the symmetric shape shown in Figure…

Q: A long rod with a thermal conductivity of 1 W / m · K is subjected to the boundary conditions given…

A: According to the given information, thermal conductivity k is 1 w/m, temperature initial T is 150…

Q: Consider a single cylindrical fin of a uniform cross-sectional area (D = 5 mm, L = 70 mm, k = 400…

Q: 1. A rod of length I with insulated sides is initially at a uniform temperature ug. Its ends are…

A: Write the differential equation satisfied by the temperature function. ∂u∂t=c2∂2u∂x2 Here, c is the…

Q: 3. The bottom of a 50mm diameter, 2mm thick metallic induction heater is 120C while its thermal…

Q: Find the two-dimensional temperature distribution T(x,y) and midplane temperature T(B/2,W/2) under…

A: Thermal conductivity, k = 400 W/mk q0 = 1000 W/m2 Temperature at mid plane needs to be evaluated

Q: Q4) A long steel bar 5 by 10 cm is initially maintained at a uniform temperature of 250 ". It is…

A: INTRODUCTION: For the stated issue First, we compute the Biot number; if it is less than 0.001, we…

Q: Q2. A thermo gate consist of an aluminum plate AB and a magnesium plate CD, each having a width of…

Q: A composite wall is made up of 10 cm of common brick against 15cm of concrete with 1.5 cm of plaster…

A: Given data:- brick concrete plaster Width(b) 10cm=0.1m 15cm=0.15m 1.5cm=0.015m Thermal…

Q: A pipe 40 cm in diameter contains steam at 100°C and is covered with asbestos (K = 0.0006…

Q: -- Two ends A and B of rod of length 20 cm have the temperatures at 30•C nd 80•C respectively until…

A: Length of rod = 20 cm Temperature at ends = 30° C and 80° C Final temperature at ends = 40° C…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

Q 2: A rod 10cm long, has its ends A and B kept at 50°C and 100°C,
respectively, until steady state conditions prevail. The temperature at
each end is then suddenly reduced to 0°C and kept so. Find the funetion
of distribution temperature along the rod?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the two-dimensional temperature distribution T(x,y) and midplane temperature T(B/2,W/2) under steady state condition. The density, conductivity and specific heat of the material are ρ =1200 kg/m 3, k=400 W/m.K, and cp=2500 J/kg.K, respectively. A uniform heat flux q =1000 W/m 2 is applied to the upper surface. The right and left surfaces are also kept at 0oC. Bottom surface is insulated.
Water at 100°C flows in a aluminum pipe with a distance 10m (0.1m insidediameter, 0.02m thick, k= 208 W/m°C). What is the heat transfer through the pipe when inside temperature is 100 °C and outside is 25 °C?
Two thermal reservoirs are connected by a solid copper bar. The bar is 2 m long, and the temperatures of the reservoirs are 80.0∘C and 20.0∘C. a) Suppose that the bar has a constant rectangular cross section, 10 cm on a side. What is the rate of heat flow through the bar? b) Suppose the bar has a rectangular cross section that gradually widens from the colder reservoir to the warmer reservoir. The area A is determined by A=(0.01m^2)[1.0+x/2.0m] , where x is the distance along the bar from the colder reservoir to the warmer one. Find the rate of heat flow and the rate of change of temperature with distance at the colder end, at the warmer end, and at the middle of the bar.
This subject is Statics of Rigid Bodies. Show your solution step by step
The composite wall of an oven consists of three materials, two of which are of knownthermal conductivity, kA = 20 W/m – K and kC = 50 W/m – K, and known thickness, LA =0.30 m and LC = 0.15 m. The third material, B, which is sandwiched between materialsA and C, is of known thickness, LB = 0.15 m, but unknown thermal conductivity kB.Under steady – state operating conditions, measurements reveal an outer surfacetemperature of 600 oC, and an oven air temperature of 800 oC. The inside convectioncoefficient h is known to be 25 W/m2 – K. total rate of heat transfer = 550 W/m2.What is the value of kB?
An perfect gas of a specific composition Molar weight is 25 grams per mole and specific heat is 3 grams per mole. Y is initially at 200kPa and 2m3 in volume. Heat transmission resulted in a twofold increase in volume. Calculate how much heat was transferred if it was subjected to a process defined by 'n=1', "n=Cp/Cv," or "n=2."
(a) A circular copper ring at 24.0°C has a hole with an area of 9.97 cm2. What minimum temperature must it have so that it can be slipped onto a steel metal rod having a cross-sectional area of 10.0 cm2?_______ °C(b) Suppose the ring and the rod are heated simultaneously. What change in temperature of both will allow the ring to be slipped onto the end of the rod? (Assume no significant change in the coefficients of linear expansion over this temperature range.)________ °C
(Picture of problem attached) A wood wall 2.5 m (» 8 ft) ´ 7 m (» 23 ft) ´ 2.5 cm (» 1 in) thick has thermal conductivity k = 0.1 W/Km. A. Find the R-value of the wall (in SI units, of course). B. If the inside and outside temperatures are 20°C and 5°C respectively, find the heat flow in watts passing through the wall. C. Now include the R-values of the air layers inside (Rin = 0.12 m^2 K/W) and outside (Rout = 0.06 m^2 K/W) the wall. Find the new heat flow. (Note: Just add all the R’s.) D. Add 10 cm of fiberglass (kf = 0.05 W/Km) to the wall. Find the R-value of the fiberglass layer. E. Find the heat flow through the wall in Watts, including air, wood, and fiberglass.
Heat loss through an insulation (k = 0.05 W/m·C) is 125 W/m2.The temperature gradient across the insulation is 100 C. Find thethickness of the insulation.
A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations? Known, Find, Schematic Diagram, Assumption, Properties, Analysis and Comments
A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations?
Two different kinds of heated metals, A and B, with masses MA and MB, temperature of TA and TB, and heat capacity CA and CB were put into a perfectly sealed container of heat capacity, Ccp, containing cold water at Tw of volume, Vw with heat capacity of Cw.Derive the working equation that will give us the final temperature of the system.Assume that the container and water has the same initial temperature.