Q 2: A sinusoidal signal v (t) =5 Cos (2 at) is transmitted using a 5-bit binary PCM system. The equalizer is of a midrise type, with a step size of 2 volt. 1. Sketch the quantizer curve ( input -output ) 2. Sketch the PCM wave for one complete cycle of the input; assume a sampling rate of four samples per second, with samples taken at t=±1/8, ±2/8, ±3/8, ±4/8 3. Determine code words at the time instants t=±1/8, ±2/8, ±3/8, +4/8

Q 2: A sinusoidal signal v (t) =5 Cos (2 at) is transmitted using a 5-bit binary PCM system. The equalizer is of a midrise type, with a step size of 2 volt. 1. Sketch the quantizer curve ( input -output ) 2. Sketch the PCM wave for one complete cycle of the input; assume a sampling rate of four samples per second, with samples taken at t=±1/8, ±2/8, ±3/8, ±4/8 3. Determine code words at the time instants t=±1/8, ±2/8, ±3/8, +4/8

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the figure of merit for an AM receiver, where the amplitude sensitivity, ka, is V0.5 Volts, and average power, P, is 1 W. For this system, calculate the required channel SNR for an output SNR of 20 dB.
kindly explain this part ,, how sinc100t is represemted in frequency domain
Plot an AM modulated signal , that has an information signal m ( t ) = 10 sin ( 10nt ) and a carrier signal c ( t ) = 15 cos ( 1000nt ) . Calculate the modulation index ( u ) . Is it a good modulation ? If no , suggest a change in one of the signals above and calculate u again , so that it approaches ideal case
A digital communication link carries binary-coded words representing samples of an input signal, xa(t)=3cos⁡(600πt)+2cos⁡(1800πt)The link is operated at 1,000 samples/s. (a) What is the folding frequency? (b) What is the Nyquist rate for the signal xa(t)? (c) What are the frequencies in the resulting discrete-time signal x(n)? (d) Will there be any aliasing here? (e) Which frequency will alias to what frequency
1. We use the DFT to compute the amplitude spectrum of a sampled data sequence with a sampling rate fs =2,000Hz. It requires the frequency resolution to be less than 0.5 Hz. determine the number of data points used by the FFT algorithm and actual frequency resolution in Hz, assuming that the data samples are available for selecting the number of data points.
An Amplitude Modulation (AM DSBFC) radio broadcasting station with its carrier frequency of 650 kHz is amplitude-modulated by a 2 kHz audio signal to produce an AM envelope. The maximum and minimum peaks voltages of the envelope are 140Vp and 60Vp respectively. The equivalent resistance of the transmitting antenna is 30 Ω. Determine: ( i ) If the transmission is changed to Single-Side Band Suppressed Carrier (SSBSC), calculate the percentage power saving in comparison to the original AM DSBFC.
During a vibration measurement experiment in the Mechanical Engineering Department at Hacettepe University, a piezoelectric accelerometer output is given by this mathemtaical equation: a (t) = 1 + 4 sin(43.98t) + 7sin(100.53t) in gravity acceleration (g) value. a) Determine the frequencies (in Hz) contained in the signal. Round your results to nearest integer value. b) What is the minimum sampling rate to avoid aliasing? c) Sketch clearly the frequency spectrum if the signal is sampled at 15 Hz. d) Now, the signal is filtered with a low-pass Butterworth filter to remove the maximum frequency component. It is desired to attenuate the amplitude of this component to at least 5 % of its value. If the sampling rate is now 20 Hz, what will be the order of the filter? e) If the blue one is our signal, then what is red and green ones? Write down the mathematical relation between the three signals? (Use labels as blue, red and green signal.)
You have an FSK transmitter using a mark frequency of 500 kHz, a space frequency of 380 kHz, and sending 10 kbps. A) How much bandwidth do you need for your transmission? B) if you are to design the system with continuous phase shift keying in mind, what would be the value of the space frequency if the mark frequency remains the same?
Message sign; m (t) = 10sinc (400 * t), and carrier sign; c (t) = 100cos (2 * pi * f * t) modulates by phase modulation. Modulation index 6, message bandwidth W = 200 Hz. • Obtain the mathematical expression of the phase modulated sign, u (t). • What is the maximum phase deviation of the modulated signal? • What is the strength of the modulated signal?
A Pulse Code Modulation based system is processing a sampled voice signals ranges from X Hz to Y Hz before it is going through the telephone line. If the bandwidth for that signalis set as 2,000 Hz, suggest a best value for X and Y.
Armstrong’s method used to generate a WBFM signal. The required WBFM signal must have fc = 5MHz and ∆f = 25 kHz. If ??1 = 25???and f?2 = 2.025MHz and crystal oscillator frequency is (43/120) M??, Draw the schematic block diagram and find all the parameters of it.
1. Given an analog signal x(t)=10 cos(2π.5500t)+5 cos(2π.7500t) is sampled at a rate of 8,000 Hz, a. Sketch the spectrum of the sampled signal up to 20 kHz; b. Sketch the recovered analog signal spectrum if an ideal low pass filter with a cutoff Frequency of 4 kHz is used to filter the sampled signal in order to recover the original signal; c. determine the frequency/frequencies of aliasing noise.