Q-8 The tension member of a roof truss consists of two unequal angles 70 x 45 x 8 with the longer legs connected by 16 mm diameter rivets. If angles are one on either side of gusset plate, then safe tension for the member will be (assuming permissible stress in tension = 150 Mpa and sectional area of angle 858 mm²).

Q-8 The tension member of a roof truss consists of two unequal angles 70 x 45 x 8 with the longer legs connected by 16 mm diameter rivets. If angles are one on either side of gusset plate, then safe tension for the member will be (assuming permissible stress in tension = 150 Mpa and sectional area of angle 858 mm²).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

BADLY NEED IN 1HOUR PLS THANKYOU Above is a simple truss with P = 45.67 KN (write answers in kN in 2 decimals) Compute for the forces in: a. Member DA b. Member BH c. Member HI d. Member DG e. Member El f. Member AF g. Resultant Force Reaction of Support F (3 pts)
Find the value of maximum load P sothat the stresses in the frame illustrated willnot exceed 120MN/m2 in tension or 90MN/m2in compression.The bars of the pin-connected frame shownhave a section of 35mmx65mm each.
The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A and C are stress-free. Ifa20-kip load is applied, determine the vertical displacement in the barat ?and C that will cause a stress in the rod at C to be 50ksi. Indicate the direction of movement. Use E=29x106psi for steel.(Provide FBD and movement diagramin your computation).
Determine the nominal moment strengt of the irregular beam shown. Assume the area of 25 mm rebar is 510 sq. mm. Given: a.) fc' = 35 MPa; fy= 413.70 MPa b.) fc' = 21 MPa; fy = 413.70 MPa
Problem #01: Analyze the given beam using flexibility method. Take moment as redundant on A and B. (CLO-1)E=30000 ksiI=800 in4 0.0015 rad
Completely solve and box the final answer. Illustrate the problem. Write legibly 4. Compute the safe concentrated load P that the beam could carry at a distance of 1 m from the fixed support with a span of 4 m from the arrangements shown below. The beam is made up of four 50 mm by 200 mm section framed. The allowable shearing stress of the beam is 0.70MPa.
Determine the concentrated load at midspan that can be added if theuniformly distributed load ω is 58 N/m that can beloaded for the beam shown if the allowable bending stress fortension is 80 MPa;, for compression is 130 MPa , for shearing stressis 48 MPa without exceeding deflection limit of L/360. E for steel is200 GPa.
Q2 Fos the bearn shown: (a) Use the stiffness method to determine all fhe resctions at supports, (b) Dras the quantitative free-body diagram of member, (€ Draw the quantitative shear diageam, bending moment disgram and qualitative deflected shape. Take J = 200(10°) mar and £ = 200 GPa.and suppon & settlement 10 mm a £ 14, - 10 &m dm dm
subj: civil engineering A 50-mm diameter bar is used as a simply supported beam 3 m long. The flexural stress is limited to 50 MPa. If w = 36. •Find Fb(bottom) and Ft(top). (F = Mc/I) •Plot the flexural stress and draw a shear & moment diagram.
A cantilever beam AB with a rectangularcross section has a longitudinal hole drilled throughoutits length (see figure). The beam supports a loadP 5 600 N. The cross section is 25 mm wide and50 mm high, and the hole has a diameter of 10 mm. Find the bending stresses at the top of the beam,at the top of the hole, and at the bottom of the beam.
A steel control rod is 5.5 ft long and must not stretch more than 0.04 in. when a 2-kip tensile load is applied toit. Knowing that E = 29 x 106 psi, determine (a) the smallest diameter rod that should be used, (b) thecorresponding normal stress caused by the load.
The midpoint B of the steel cantilever beam ABC is supported by a vertical aluminum rod. Find the maximum allowable value of the applied force P if the stress in the rod is not to exceed 120 MPa. Use Est = 200 GPa, I = 50 x 106 mm4 for the beam, Eal = 70 GPa, and A = 42 mm2 for the rod.