Q/ Design the rectangular duct system shown in figure below using equal friction method with frictional pressure drop of 1 pa/m. and allowable height is 300 mm assume the dynamic loss coefficient for elbow and exitas =1. 0.6 m /s 0.6 m'/s D 2m 2m 2m F 2m Fan 2m E B A 5m K 2mH G 2m 2m 2m 2mI 0.6 m/s 0.6 m /s Mechanical Engineering Department Subject : AC and Refrigeration

Q/ Design the rectangular duct system shown in figure below using equal friction method with frictional pressure drop of 1 pa/m. and allowable height is 300 mm assume the dynamic loss coefficient for elbow and exitas =1. 0.6 m /s 0.6 m'/s D 2m 2m 2m F 2m Fan 2m E B A 5m K 2mH G 2m 2m 2m 2mI 0.6 m/s 0.6 m /s Mechanical Engineering Department Subject : AC and Refrigeration

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows from a large reservoir at the rate of 0.0137 m3/s through the system shown in the Fig. below. Calculate the pressure at B. NB: Use f = 0.017 (friction factor) and fT = 0.010 in zone of complete turbulence. Hint: Include minor losses, assume K = 1.0 for the inlet or entrance and use the applicable appendix at the back of the textbook to obtain the pipe parameters.
A vertical pipe 3 ft in diameter and 30 ft long has a pressure head at the upper end of 22 ft. of water. When water flows through it with mean velocity of 15 fps, the friction loss is 6 ft. Find the pressure head in ft. at the lower end of the pipe when the flow is upward. a.69.6b.46.0c.89.6d.58.0
A- A regulator with discharge = 22m3/sec , rounded entrance is used for piers and abutment , water level at flood time =92.8 , bed level=90.3m at u/s. D/s water level = 92.2m.Bed level under gate: 91m. Decide the flow condition after the gate when it is opened partially (free or submerged), then find the value of partial opening . no of piers=2, each one has thickness =1m . B - For a stiffy clay soil Do you accept depth of flow = 3m with So=0.0007 if the ratio of B/y=3 and the cross section of the canal was rectangle? Why?
An overhead water tank is to supply water from 15th floor thru a booster pump. Thewater surface for the overhead tank is maintained at Elevation 47m and the lowestpoint of supply is at elevation 0m. The head of the booster pump is 46ft and the flowcapacity is 65gpm. Determine the pressure of water at ground floor from the givendata and if the material specification of the riser pipe used for distribution is PN 20does the pressure rating of the pipe can withstand the highest pressure available inthe system?
Water at 20 ° C exits to the standard sea-level atmospherethrough the split nozzle in Fig. P3.62. Duct areas are A 1 50.02 m 2 and A 2 = A 3 = 0.008 m 2 . If p 1 = 135 kPa (absolute)and the fl ow rate is Q 2 = Q 3 = 275 m 3 /h, compute theforce on the fl ange bolts at section 1.
The rectangular bin with an inclined gate AB is filled with water to the depth shown. Determine the location in meters along with the inclination of the center of pressure from the water surface when the total pressure is acting on gate AB x=0.82 a=2.02 m b=30 degrees asap 15 mins
A vertical conical pipe has diameter 1.5 ft at the top and 3.0 ft at the bottom and 60 ft long. The friction loss is 10 ft for flow in either direction when the velocity at the top is 30 fps and the pressure head there is 6.5 ft of water. Find the pressure head in ft at the bottom when the flow is upward. a.69.6 b.58.0 c.89.6 d.46.0
A pump transfers water from a large 0pen tank to another tank above it. At the suction side, the friction losses is equivalent to 6.4ft of water. The vapor pressure of water is 0.46psi. If the NPSH available is 15ft, calculate the elevation difference bet the open tank and the pump.
A jet is issued from the side of a tank under a constant head asshown in the figure. The side of the tank has an inclination of 1H:1V.The total depth of water in the tank is h1 = 6.7m and the orifice islocated at h2 = 3.7m above the bottom of the tank. The the horizontalfloor surface is at h3 = 1.2m below the bottom of the tank. If Cv = 1.0and neglecting air resistance, then Determine the maximum height (y) to which the jet will rise abovethe orifice.
Water flows down a vertical pipe whose diameter increases suddenly from 175 mm to 350 mm. The discharge in the pipe is 85 lps. The pressure 0.6m above the enlargement section is 275 kPa. Find the pressure at a section 0.6 m below the enlargement section.
Ans. 1.941m/s I need solution #hydraulics
Hydraulics (Metacentric Height) 1. A ship with a total displacement of 1,800 tonners rolls to one side thru an angle of 1 degree when a deck load of 5 tonners is moved laterally thru a distance of 4.5m. Compute the metacentric height for this particular position of the vessel. Note: Use 4 decimal places show FBD and full solution