Q. A house wall may be approximated as two 1.2 cm layers of fiber nsulating board, an 8.0 cm layer of loosely packed asbestos, and a 10 cm ayer of common brick, the high and width of the wall are 3 and 5m respectively. The wall contain a window with single glass plate 5 mm thick, the high and width of the window are 1 and 1.5m respectively. If the inside and outside of wall temperature are 15 and 45 C° respectively, calculate the heat-transfer for this arrangement. Note: for fiberglass k = 0.038 W/m.Co, asbestos k=0.154 W/m.Co, brick k-0.69 W/m.C°, glass k-0.78 W/m.Co

Q. A house wall may be approximated as two 1.2 cm layers of fiber nsulating board, an 8.0 cm layer of loosely packed asbestos, and a 10 cm ayer of common brick, the high and width of the wall are 3 and 5m respectively. The wall contain a window with single glass plate 5 mm thick, the high and width of the window are 1 and 1.5m respectively. If the inside and outside of wall temperature are 15 and 45 C° respectively, calculate the heat-transfer for this arrangement. Note: for fiberglass k = 0.038 W/m.Co, asbestos k=0.154 W/m.Co, brick k-0.69 W/m.C°, glass k-0.78 W/m.Co

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.4P: 1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus...

See similar textbooks

Similar questions

Both ends of a 0.6-cm copper U-shaped rod are rigidly affixed to a vertical wall as shown in the accompanying sketch. The temperature of the wall is maintained at 93C. The developed length of the rod is 0.6 m, and it is exposed to air at 38C. The combined radiation and convection heat transfer coefficient for this system is 34W/m2K. (a) Calculate the temperature of the midpoint of the rod. (b) What will the rate of heat transfer from the rod be?
1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
A section of a composite wall with the dimensions shown below has uniform temperatures of 200C and 50C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials are: kA=70W/mK,kB=60W/mK, kC=40W/mK, and kP=20W/mK, determine the rate of heat transfer through this section of the wall and the temperatures at the interfaces. Repeat Problem 1.34, including a contact resistance of 0.1 K/W at each of the interfaces.
1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.
2.5 Derive an expression for the temperature distribution in a plane wall in which there are uniformly distributed heat sources that vary according to the linear relation where is a constant equal to the heat generation per unit volume at the wall temperature . Both sides of the plate are maintained at and the plate thickness is 2L.
2.3 The shield of a nuclear reactor is idealized by a large 25-cm-thick flat plate having a thermal conductivity of . Radiation from the interior of the reactor penetrates the shield and there produces heat generation that decreases exponentially from a value of at the inner surface to a value of at a distance of 12.5 cm from the interior surface. If the exterior surface is kept at 38°C by forced convection, determine the temperature at the inner surface of the field. Hint: First set up the differential equation for a system in which the heat generation rate varies according to .
1.3 A furnace wall is to be constructed of brick having standard dimensions of Two kinds of material are available. One has a maximum usable temperature of 1040°C and a thermal conductivity of 1.7 W/(m K), and the other has a maximum temperature limit of 870°C and a thermal conductivity of 0.85 W/(m K). The bricks have the same cost and are laid in any manner, but we wish to design the most economical wall for a furnace with a temperature of 1040°C on the hot side and 200°C on the cold side. If the maximum amount of heat transfer permissible is 950 , determine the most economical arrangement using the available bricks.
The handle of a ladle used for pouring molten lead is 30 cm long. Originally the handle was made of 1.9cm1.25cm mild steel bar stock. To reduce the grip temperature, it is proposed to form the handle of tubing 0.15 cm thick to the same rectangular shape. If the average heat transfer coefficient over the handle surface is 14 W/m K, estimate the reduction of the temperature at the grip in air at 21C.
1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1