Q. No 1). Determine the discharge through a trapezoidal channel having X m base width, Side slope is2:1 (Vertical to Horizontal). If the height of free surface of the water above the bed is 4 m. The bedslope is 1 in 1500, take n= 0.012. Width X=85Q. No 2). A pipe line is designed to supplying water with flowrate of X 1/s to fulfil the demand andconsumption of a city. Determine the head loss and velocity of flow in 1500 m long water supply linesection having diameter of Y cm. Assuming coefficient of friction factor f= 0.00155. X (Flowrate)= 88Y (Diameter)= 21.6Q. No 3). A water supply pipe line is designed to supplying water to a nearby city. Determine velocity ofwater when it reach to a location 1.3 km from the pumping station where maximum head loss was foundto be X m. Assume that pipe used is having diameter of Y cm and commercial steel pipe is used in theproject. X(Headloss,m) =2, Y (Dia, cm) = 169Q. No 4). A rectangular channel of X ft width is supplying water at flowrate of Y ft'/s. If the slope ofchannel is 1/800 calculate the depth of water in the channel. Assume value of manning coefficient , n =0.015.Q. No 5). A horizontal galvanized rectangular iron pipe (20x 50 cm) is supplying water with flowrate of0.4 m3/s to a town X m from the pump house. Calculate the pressure drop in Pascal at that point. Assumethe friction factor for pipe is f= 0.016, use equivalent diameter D= 4R and Pressure drop = y hi

Depth of the water in channel y= 4.0 mwidth of the base X=85 mSide slope = 2V:1H=1V:0.5H here…

Q. No 1). Determine the discharge through a trapezoidal channel having X m base width, Side slope is 2:1 (Vertical to Horizontal). If the height of free surface of the water above the bed is 4 m. The bed slope is 1 in 1500, take n= 0.012. Width X 85

Q. No 1). Determine the discharge through a trapezoidal channel having X m base width, Side slope is 2:1 (Vertical to Horizontal). If the height of free surface of the water above the bed is 4 m. The bed slope is 1 in 1500, take n= 0.012. Width X 85

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Water flows through a semi-circular weir 2 m deep and 4 m wide at the top under a head of 1.50 m.…

Q: 4. Determine the dimensions and the critical depth of the following open channels cross-sections of…

A: Given information in question Area Discharge Angle made by side of trapezoidal channel To find out…

Q: A 4 m wide rectangular channel, having bed slope of 0.001 carries a discharge of 16 16 m³/s.…

A: Given data in question Bed slope Discharge Constant Width To find out Category of channel

Q: The discharge Q of an open channel can be measured using a V-notch weir which is a vertical plate…

Q: 2. Water flows through a semi-circular weir 2 m deep and 4 m wide at the top under a head of 1.50 m.…

Q: find the length of the water profile for a wide rectangular that has a bed slope of 7.5 cm/km and…

A: Given: Wide rectangular channel terminates into sudden fall Critical depth at the sudden…

Q: The channel is 2 m wide and transports water at 18 m3 /s. The elevation of the bed is raised 0.25 m.…

A: The flow in upstream is equal to the flow in the downstream, let considering the energy head in the…

Q: A trapezoidal canal has bottom width of 2m and side slope of 2V:3H is laid on the slope of 2 meters…

Q: The discharge Q of an open channel can be measured using a V-notch weir which is a vertical plate…

Q: A trapezoidal channel with a bottom width of 10 m carries a flow of 1000 m/s. The side slope z = 2,…

A: Aside from the perplexing number related we do to observe that best cross part of a channel for an…

Q: aquifer at 100 to the horizontal. The difference in water level between to observation points of 60…

Q: An earthen channel with a based 3 m wide and side slopes 1:1 carries water with a depth of 1m. The…

Q: Determine the discharge over a right angled triangular notch of depth 0.36 m. Let the coefficient of…

Q: A trapezoidal channel 5 m wide and having side slopes of 1.5 horizontal: 1 vertical is laid on a…

A: The Manning's formula is given by: Q=1ηAR23S12 Where, Q = Discharge A = Area of trapezoid R =…

Q: A drainage canal in the shape of trapezoid with a bottom width of 2,3m and a side slope of 1…

A: B=2.3m y=2.8m n=0.012 S=0.0004

Q: Question: The 1 meter wide rectangular cross-section open channel system, whose longitudinal profile…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: 1. The discharge and velocity of water in a rectangular channel are 75m^3/s and 5m/s respectively.…

A: To find : Hydraulic radius.

Q: The discharge from a 150 mm diameter orifice under a head of 3.05m and C=.6 flows into a rectangular…

A: Given: The diameter of the orifice is 150 mm. The head is 3.05 m. The value of C is 0.6. The width…

Q: The rectangular channel is 3 m wide and caries a flow of 10 m3/s. At the 3.5 m drop, water is at the…

A: Hydraulic jump: Hydraulic jump is defined as the rise of water, this is occurred due to the…

Q: The width and the depth of flow in a triangular channel is 4 m and 1 m respectively. The velocities…

A: Given: Width of channel = 4 m Depth of channel = 1 m Velocity 0.2 m below surface, V0.2 = 0.6 m/s…

Q: discharge = 6.5 m^3/sec Considering the best hydraulic cross-section, what is the critical depth…

A: Given- Discharge = 6.5 m3 /sec Best hydraulic cross section Top width (T) = 2z ( side length)…

Q: A trapezoidal open channel carries water at a depth of 2m. The canal has a bottom width of 6m and a…

Q: A rectangular channel of width 5 m is carrying a discharge of 100 m/sec. The Froude number of the…

Q: A trapezoidal channel of bed width 12.0 m, side slopes 2:1, longitudinal bed slope = 10 cm/km,…

Q: A sluice gate is used to control the flow of water in a horizontal rectangular channel, 6 m wide.…

Q: In a rectangular channel, find the maxium step height (to 2 d.p. ) so that the flow passes over the…

A: For max step size use relationE1=Ec+Δzmaxyc=q2g13yc=4529.8113=5.90997m

Q: 6. Find the discharge through totally drowned orifice of width 3.3 m if the difference of water…

Q: A 4 m wide rectangular channel, having bed slope of 0.001 carries a discharge of 16 m³/s.…

A: Given- Discharge Q=16 m3/sn=0.012g=10 m/s2width B=4 m

Q: Q3/ Determine the state of flow in a rectangular channel of (3m) width and depth of flow is (1m) and…

Q: Find the normal depth for a discharge of 6.371 m/s in a trapezoidal channel with a bottom width of…

A: Let the normal depth is y. The discharge is Q=6.371 m3/s. The bottom width is b=1.524 m. The…

Q: Design an irrigation canal to carry a discharge of 14 m / sec, assume the Manning's roughness…

A: Given Discharge = 14m3/s n = 0.0225 Z = 0.5 b/d = 5.7

Q: 13. (LAB) A discharge of 25 m/s is passing in a rectangular channel of bed width 8.0 meters and…

A: Hydraulic jump: The hydraulic jump occurs in the open channel flows. The flowing water is having…

Q: 4.a. A trapezoidal channel 5 m wide and having side slopes of 1.5 horizontal: 1 vertical is laid on…

A: Given that: Base width of the channel, B = 5mSide slope: m = 1.5Longitudinal…

Q: The 4m wide square cross-section is 2.5m deep with a flow rate of 10m^3/s. Determine the depth of…

Q: Example: A 4.5-m wide trapezoidal channel having a side slope of 1.5 horizontal: 1 vertical is laid…

A: Given: The bottom width is 4.5 m. The side slope is 1.5H:1V. The bed slope is 0.00035. The discharge…

Q: In a triangular channel, the velocity along the centre line at a depth of 0.2 m and 0.8 m is 0.7 m/s…

A: Given data: Velocity at depth of 0.2 m, V0.2 = 0.7 m/s Velocity at depth of 0.8 m, V0.8 = 0.5 m/s…

Q: 3. A steep-sided triangular section channel (0 = 60°) has a flow rate of 300 m/s. Find the critical…

Q: distance of 60 m is 5 m. Determine the discharge through the aquifer per unit width if k= 0.7…

A: We knowQ=kiAi=hydraulic gradienti=h2-h1Li=560

Q: A discharge of 175 cubic meters per second is passing through a trapezoidal weir with a discharge…

Q: A triangular-shaped inflow assuming it is completely f crest is 20 m wide and has km^2 and has…

Q: Q. No 1). Determine the discharge through a trapezoidal channel having X m base width, Side slope is…

A: Given: n=0.012S=11500width=85

Q: A rectangular open channel 3 m wide, carries a discharge of 8 m/s at a flow depth of 2 m. The…

Q: A rectangular open channel, with a constant discharge of 32m3/s, has a smooth expansion from (1) to…

A: Given that, Constant discharge (Q)=32 m3/sec. Consider B1=3.6 m, y1=2.4 m Using the continuity…

Q: be B and the depth be y, termine the hydraulic radius of the channel. a) By/ R+2Y

A: To find : Hydraulic radius

Q: The water surface elevation at upstream section is 100m. The bed slope is 0.002 under uniform flow.…

Q: Que. Find the discharge through a trapezoidal notch which is 2m wide at the top and 0.80m at the…

Q: 5) Determine the flow in a trapezoid channel having base width of 4m and side slope 1:1 if the…

A: Trapezoidal channel: The trapezoidal channel is one of the open channels which is said to be the…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

Q. No 1). Determine the discharge through a trapezoidal channel having X m base width, Side slope is
2:1 (Vertical to Horizontal). If the height of free surface of the water above the bed is 4 m. The bed
slope is 1 in 1500, take n= 0.012. Width X=85
Q. No 2). A pipe line is designed to supplying water with flowrate of X 1/s to fulfil the demand and
consumption of a city. Determine the head loss and velocity of flow in 1500 m long water supply line
section having diameter of Y cm. Assuming coefficient of friction factor f= 0.00155. X (Flowrate)= 88
Y (Diameter)= 21.6
Q. No 3). A water supply pipe line is designed to supplying water to a nearby city. Determine velocity of
water when it reach to a location 1.3 km from the pumping station where maximum head loss was found
to be X m. Assume that pipe used is having diameter of Y cm and commercial steel pipe is used in the
project. X(Headloss,m) =2, Y (Dia, cm) = 169
Q. No 4). A rectangular channel of X ft width is supplying water at flowrate of Y ft'/s. If the slope of
channel is 1/800 calculate the depth of water in the channel. Assume value of manning coefficient , n =
0.015.
Q. No 5). A horizontal galvanized rectangular iron pipe (20x 50 cm) is supplying water with flowrate of
0.4 m3/s to a town X m from the pump house. Calculate the pressure drop in Pascal at that point. Assume
the friction factor for pipe is f= 0.016, use equivalent diameter D= 4R and Pressure drop = y hi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Question no. 1 Given data

VIEW

Step 2 Discharge through channel

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bed of a corrugated channel, with Manning’s coeffcient n =0.019 s/m^1/3 drops 25 m every 1500 m. The channel has a semi-circular cross section with total width of W = 10 m (i.e. radius of the semi-circle is 5 m). 1. Given that the stream has a water depth of h = 2.5 m, find the flow rate in the stream 2. A concrete divider with the same Manning’s coeffcient was installed at the middle of the stream. Given that the total flow rate in the stream stays the same, would the water depth in the stream change as a result of the divider? If so, would it increase or decrease? Would the stream velocity change? If so, would it increase or decrease? You may assume the thickness of the divider to be negligible.
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m3s is to occur in the cast-iron pipe? Use f = 0.021 for all pipes. Draw the HGL and the EGL, including changes in slope due to head loss. Neglect minor losses.
Water is flowing in a rectangular channel that has a width b-3 m. If the depth of flow y = 2 m and Froud Number NF33, then the flow rate (Q) in the channel is
Determine the critical depth for best hydraulic cross-section of a trapezoidal channel that carries a flow of 6.5 m³/ s. Note: For Best Hydraulic Cross-Section; T = 2 z where T – top width and z-side length, and R = y/2.
A circular section channel 3 m in diameter has a depth of 1.0 m and is laid to a gradient of 1:1000 and n = 0.012. A.Compute the rate of flow in cu.m./s (2 decimal places) B. Compute the hydraulic radius of the channel (3 decimal places).
Two reservoirs are connected by a pipeline consisting of pipe 1, pipe 2, pipe 3connected in series with length of 170 m, 300 m, 210 m respectively. Thedifferent in water surface levels in two reservoirs is 12 m. The friction coefficientfor pipe 1, pipe 2 and pipe 3 are 0.0052, 0.005 and 0.0048 respectively. Based onTable 2 and the setting given, determine the flowrate of the flow if the entranceloss coefficient is 0.25 considering :(i) minor losses; and(ii) neglecting minor losses pipe 1 =230(mm) Pipe 2 =330(mm) Pipe 3 = 430(mm)
Determine the normal depth (m) in a rectangular channel with flowing discharge of 70 m3/s, roughness of n=0.025, slope of 0.001, with bottom width of 6 meters.
Q/ Find the Width of channel if it has side slope and bed slope ( 1 : 1 ) and ( 1 to 1000 ) and the ratio of the width to the depth of cannel 2 respectively the discharge is 15 m3 / sec and coefficient C = 60 .
Water flows at a depth of y1=0.4ft in a concrete channel which is 10ft wide. The discharge per unit width is 10ft2/sec. Estimate the height of the hydraulic jump that will be formed if bed slope is equal to 0.0 and 0.15 respectively.
Determine the depth of the trapezoidal canal with sides sloping at 60ᵒ with the horizontal in order to have a minimum seepage. The canal is to carry a discharge of 25 m3/s with an average velocity of 1 m/s. Note: for minimum seepage = bottom width = 4(depth)(tanθ/2)
A masonry dam having a sheet piling cutoff at the upstream and is located at a reservoir site as shown in the figure. Nf= 4; Nd= 10 and K= 0.003m/min 1) compute the seepage discharge in cu MTR/day 2) compute the uplift force acting on the base; 3) compute the exit or escape gradient of the water at the downstream tip of the dam if the length of the flow field is equal to 1.80m
A rectangular channel 3.6m x 1.8m deep discharge 6.8 cu.m per sec. If the same consideration have been used for a trapezoidal section having the same perimeter, what would have been the discharge possible with the swme hydraulics slope? In cu.m/s