{Q.1} A three-phase induction motor runs at almost 1198 revolutions per minute (rpm) at no load and 1112 rpm at full load when supplied from a 60-Hz, three-phase source. (a) How many poles does this motor have? (b) What is the slip in percent at full load? (C) What is the corresponding frequency of the rotor currents? (D) What is the corresponding speed of the rotor field with respect to the rotor and with respect to the stator?

Answered: Image /qna-images/answer/04dbd76a-6eaf-41c1-8ddd-48bdfb9891a4.jpg

{Q.1} A three-phase induction motor runs at almost 1198 revolutions per minute (rpm) at no load and 1112 rpm at full load when supplied from a 60-Hz, three-phase source. (a) How many poles does this motor have?

{Q.1} A three-phase induction motor runs at almost 1198 revolutions per minute (rpm) at no load and 1112 rpm at full load when supplied from a 60-Hz, three-phase source. (a) How many poles does this motor have?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 13RQ: A squirrel-cage induction motor is operating at 1175 RPM and producing a torque of 22 Ib-ft. What is...

See similar textbooks

Related questions

Q: A balanced delta load of 3 + j4 ohms per phase is connected to a balanced 110v source. Find the line…

Q: Vcc+12 V Solve for the following: (a) IBQ and ICQ. (b) VCEQ. (c) VB and VC. (d) VBC. RC 2.2 ka Re…

A: The above circuit is for small signal amplification.so the transistor is biased in active region.so…

Q: 3z2-7z X(z) for the sequence x(n) =2 u(n) + 3" u(n) is (z-1)(z-3)

Q: . A balanced delta connected load whose impedance is 45470° ohm per phase, a three phase motor that…

A: Notes Line voltage and phase voltage in delta connected system remain same. Line current and phase…

Q: Det voi, A, Ra R2 iro 1 R, RA

Q: The two conducting planes illustrated in Figure 6.14 are defined by 0.001 <p< 0.120 m, 0 < z < 0.1…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: (wt + 68") amp respectively, BAC circuit. What is the impedance of a balanced wye connected load and…

A: The solution is given below

Q: 4. Determine the Thevenin's and Norton's equivalent circuits across a-b. 24V + 3A ob

Q: n a superheterodyne receiver, why is it important to convert the RF Signal to IF Signal before…

A: Superhetrodyne Receiver :It is a radio receiver which consists the frequency level which is the…

Q: {B] Given the measurement VS 1.7 V for the network of the following figure determine: 2 kn a. IDo.…

A: We need to find out current and voltage for given circuit

Q: An alternator has 16 poles. At what speed must it be driven to develop 25cycles

Q: 3.10 ! An infinitely long cylindrical dielectric of radius b contains charge within its volume of…

A: We need to find out electric field of given charge distribution

Q: In a 3 phase 4 wire system, the line voltage is 440v and non inductive loads of 20, 16, and 10kw are…

A: Given: Loads-20kW, 16kW and 10kWVoltage,VLine=400VSo,Phase Voltage, Vph=4003V

Q: 1. The most commonly used liquid for transformer insulation is (a) mineral oil (b) askerals (c)…

A: We need to select correct option for given statement

Q: In the circuit in Figure 1, determine i(t) at t> 0. t = 0 12 V 4 3 H Figure 1

Q: deterptiar the alue to a clese leep Coantael Date. tn a cteed teep Contrel system $s Hal, yte due to…

Q: b. 833/2 For items: 21- 25 R-100 R-50 R-100 L R-100 R-100 48V R150 R-50 Solve for 26. Reg-? A4150E…

Q: A carrier of frequency 900kHz is being Amplitude Modulated (AM) by a modulating signal that is a…

A: We need to find out frequency of amplitude modulated signal

Q: B4. (a) A 380V, 50 Hz, 4-pole, 1460 rev/min, star-connected three-phase induction motor is driven by…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 18 V (B] Given the measurement VS = 1.7 V for the network of the following figure determine: 2 kn a.…

A: MOSFET: It is a semiconductor device that has a very high switching frequency in their group…

Q: X(2) TOn the sequence x(n) = 2" u(-n – 1)-)" u(-n - 1) is- -1,5z (-2)(x

Q: X(Q for the sequence x(n) =6(n-2) is

Q: R1 = R'2 = 0.080 X1 = X'2 = 0.2 Q Re = 1000 Q; Xm = 400 Q It is supplied to the load Z' at 240 V, 6…

Q: R1 = R'2 = 0.08 Q X1 = X'2 = 0.2 Q Re = 1000 Q; Xm = 400 Q It is supplied to the load Z' at 240 V, 6…

Q: The value of form factor

Q: For the relationship of the ABCD CONSTANTS OF TRANSMISSION LINES: Vs = AVR + BIR CVR + DIR Is V Vs…

Q: i, = 3 sin(377t + 60°) R1.2 N XL 1.20 Ω Χ. 20 Xc

Q: H.W. Find the current I in the following network: V = 10/20° v (+ ZR = Z, = j2N Zc=-j10 { ZR = 4 0 =…

A: The solution is given below

Q: t = 0. Determine; Neper frequency, a resonant frequency, ®o. a) b) c) natural frequency, si and s2.…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: 1 X(2or the sequence x(n) = 2"-3 u(n - 3)is z-3 (1-2z-3)

A: The solution is given below

Q: An alternator has 16 poles. At what speed must it be driven to develop 40 cycles

Q: If a converging lens has a focal length of 20 cm, at which object distance will an image larger than…

A: The solution is provided in the following section.

Q: Q5) For the amplifier circuit shown in figure +10 V (4), calculate Figure (4) the voltage gain of…

A: We need to find out the voltage gain for given circuit

Q: 3. The equation for a current is given by i = 20.2513 sin a. At what angles will the instantaneous…

A: We need to find out value of angle for given current value .

Q: Problem 3.5 a.) In the circuits shown in Fig. P3.3 (a)-(d), find the equivalent resistance seen by…

Q: X(2) Tor the sequence x(n) =(3" coswon)u(n) is- 1-(3coswo)z 1 1-(2coswo)z 1+9z-2

Q: Draw block diagram /circuit diagram of the ff. FM circuits and discuss the operation. 2. FM…

Q: #6) For the BJT transistor circuit given below, determine: IB, lc, lE, VCE, and Vce Page | Re Vcc RB…

A: In this question, We need to determine the all known currents and voltage. We know Forward bias…

Q: Given the analog signal x(t) = sin(480πt)−3sin(720πt) that is sample at 600 times per second, what…

Q: 4=4 Disceuss of a Lontrol system, for differe 7ypes input , 9 static the steady state behar with the…

A: In this question we will find steady state behaviour of control system using static error…

Q: Question 9 The following signal goes through a lowpass filter with cutoff frequency of fc=100HZ.…

A: A waveform of a signal is given in the question. This is signal is allowed to go through a low pass…

Q: Question # 1: What if a shunt generator is started and no voltage builds up? What could be wrong?…

A: Voltage build up is a process that enables a generator to run in continuous manner. But sometimes it…

Q: d=o need to convert the drawing from a handwritten drawing to a typeface on the computer, please

A: I need to draw the image in the computer.

Q: single phase transformer has primary turns

Q: 2. The rms value of the voltage in a 60 cycle is 230 V. What is the equation of the sinusoidal wave?

A: Note: As per our company guidelines we are supposed to answer only one question. Kindly repost other…

Q: 2. Design an ideal non-inverting opamp witha closed-loop gain of Av=10. When vi =0.8V, the current…

A: We need to design a non inverting amplifier

Q: Design a logic circuit which will give a 1 output when any two of the three inputs A, B, and C are…

Q: is iR i, ic 102 6mH E20µF 150 sin(2500t – 34°)V-

Q: 8(A) For the BJT transistor circuit shown below, determine whether the transistor is biased in: а.…

A: We need to find out current and voltage for given circuit and region of operation

Q: a) Find the voltage across the te

Concept explainers

Single Phase Induction Motor

The single-phase induction motor or engine consists of a single rotating phase in the stator and a rotating cage in the rotor. When phase one supply is connected to the stator winding, a magnetic field is generated. In the pulsating field, the rotor does not rotate due to inertia. So, a single-phase import motor does not start and requires some initial methods.

Question

{Q.1} A three-phase induction motor runs at almost 1198 revolutions per minute (rpm) at no load and 1112 rpm at full load when supplied from a 60-Hz, three-phase source.

(a) How many poles does this motor have?

(b) What is the slip in percent at full load?

(D) What is the corresponding speed of the rotor field with respect to the rotor and with respect to the stator?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Name three factors that determine the torque produced by an induction motor.
A squirrel-cage induction motor is operating at 1175 RPM and producing a torque of 22 Ib-ft. What is the horsepower output of the motor?
The rotor of a 6-pole, 50-Hz induction motor is rotated by some means at 1000 r.p.m. Compute (i) rotor voltage (ii) rotor frequency (iii) rotor slip and (iv) torque developed. Can the rotor rotate at this speed by itself?
A three-phase, two-pole, 35 hp, 480 V, 60 Hz, Y-connected induction motor has the following constants in ohms per phase referred to the stator: Rl = 0.322Ω R2 = 0.196 Ω X1 = 0.675Ω X2 = 0.510Ω Xm = 12.5Ω The total rotational losses are 1850 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 3% at the rated voltage and rated frequency, determine the following: (a) The speed in rpm and in rad/s (b) The stator current (c) The power factor (d) The developed power and output power (e) The developed torque and output torque (f) The efficiency.
A 3-phase, 4-pole, 230-V, wound rotor induction motor has both its stator and rotor connected in Y. The stator has half as many turns per phase as the rotor. It has a rotor resistance and blocked rotor reactance of 0.09 and 0.385 ohm respectively. If the rotor is turning at 1760 rpm, determine the rotor power developed in hp. *
A 480V, 60Hz, six-pole, Y connected cage rotor induction motor has the followingparameters in ohms per phase referred to the stator: R1=0.5Ω X1=1.1Ω R2=0.45ΩX2=0.6Ω Xm=30Ω The total rotational losses (friction, windage, and core losses) are 1100W and are assumedto be constant. For a rotor slip of 2.2% at the rated voltage and rated frequency, calculate:a) Rotor speedb) Stator currentc) Complex, real, and reactive input power and the power factor of the machined) The air-gap power (Pag) and the developed mechanical power (Pconv)e) Developed electromechanical torque, and the output mechanical torquef) Efficiency
A four-pair of pole, 50-Hz squirrel-cage induction motor runs on load at a shaft speed of 720 rpm. Calculate the frequency (hertz) of induced current in the rotor.
14 P.14 - A three-phase induction motor with 4 magnetic poles, 60 Hz, rotates with a speed of n=1750 rpm In order to achieve a quick stop we can use a proper swap of 2 phases which normally corresponds to an inversion of rotation direction. For fast crossing, the technique of inversion of the direction of rotation by changing 2 phases is used. At the precise moment we swap the 2 phases, what are the slip, s, and the rotor current frequency, fR, like?
Three-phase induction motor, 460 V 50 Hz, 4 poles, 50 hp with Delta, operating at 3.8% slip rated torque when receives Line Voltage 460 V, 50 Hz The parameters of the equivalent circuit per phase are as follows.R1 = 0.33, X1 = X2 = 0.42 and Xm = 30 Ohm / phase.Answer the following questions by neglecting the mechanical losses, Core losses and Stray load losses.A) Value of the rotor resistance R2 B) Maximum torque and rated speed C) line current and starting torque of motor
A three-phase induction motor used for a commercial application in Oman runs at 586 rpm at no load and at 540 rpm at full load. a) How many poles do this motor have? b) What is the percentage slip at full load? c) The frequency of the rotor currents when slip is 7 % d) The frequency of the rotor currents at standstill.
A 3-phase, 6 pole, 440 V, 60 Hz, Y-connected induction motor has the following impedances per phase referred to the stator circuit: R1=0.43 Ω, R2=0.54 Ω, X1=1.263 Ω, X2=0.608 Ω, XM=43Ω The total rotational losses are 1100 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2 percent at the rated voltage and rated frequency, Find the motor speed, stator current, output power
A 440-V-rms (line-to-line voltage) three-phase induction motor runs at 1150 rpm driving a load requiring 15 Nm of torque. The line current is 3.4 A rms at a power factor of 80 percent lagging. Find the output power, the power loss, and the efficiency.