Q.1. Refer to the infinite slope shown in Figure 1. Given: B = 29 °, y = 21 kN/m3, Ø = 32 °, and c' 37 kN/m2. Find the height, H, such that a factor of safety, Fs 3 is %3D maintained against sliding along the soil-rock interface. b. Determine the thrust on the wall if the water table rises to a level 1 m below the surface of the sand. The saturated unit weight of the sand is 22 kN/m3.

Q.1. Refer to the infinite slope shown in Figure 1. Given: B = 29 °, y = 21 kN/m3, Ø = 32 °, and c' 37 kN/m2. Find the height, H, such that a factor of safety, Fs 3 is %3D maintained against sliding along the soil-rock interface. b. Determine the thrust on the wall if the water table rises to a level 1 m below the surface of the sand. The saturated unit weight of the sand is 22 kN/m3.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.5P

See similar textbooks

Similar questions

Q.1. Refer to the infinite slope shown in Figure 1. Given: β = 19 ͦ, ɣ = 20 kN/m3 , Ø = 33 ͦ, and c’ = 47 kN/m2 . Find the height, H, such that a factor of safety, Fs = 3.1 is maintained against sliding along the soil-rock interface. Also Determine the thrust on the wall if the water table rises to a level 2 m below the surface of the sand. The saturated unit weight of the sand is 20 kN/m3 .
Determine the total active thrust, in kN/m, for a retaining wall (height 5.60 m) with horizontal backfill given the following properties: Unit weight = 17.42 kN/m3, angle of internal friction = 32 degrees, Cohesion = 11.76 kPa, Surcharge = 9.32 kPa.
Consider the smooth retaining wall shown in the figure below. Calculate the overturning moment at Point O in kN.m due to the surcharge only applied behind the wall. Assume that the surcharge is applied over a wide area. Consider a 1 m thickness in the out-of-plane direction
Determine the total active thrust, in kN/m, for a retaining wall (height 4.77 m.) with horizontal backfill given the following properties: Unit weight = 17.49 kN/m3, Angle of internal friction = 32°, Cohesion = 11.32 kPa, and Surcharge = 8.6 kPa. Round off to two decimal places.
A wall 6m high retains sand having a dry density of 15.40 KN/m3. Angle of internal friction of 32' and void ratio of 0.68. Use rankine theory. a. Determine the active thrust in kN per unit length of wall if there's ground water table located 2.5m below the ground. b. Determine the location of resultant thrust from the ground surface considering the ground water table located 2.5m below the ground.
A braced wall is shown in Figure 14.20. Given: H = 7 m, naH = 2.8 m, =30, =20, = 18 kN/m3, and c = 0. Determine the active thrust, Pa, on the wall using the general wedge theory. Figure 14.20
3. An infinite slope has shear strength parameters at the interface: c = 30 kPa, φ = 30°, γ = 17 kN/m3 (Assume 1 m strip perpendicular to the paper and 1 m strip along the inclination of the infinite slope). a. If H = 5 m, and β = 20°, find the sliding force. b. If H = 5 m, and β = 20°, find the force that resist sliding on the rock surface. c. If HCR = 8 m, find the minimum angle β so that the slope is stable.
Q.9 A smooth retaining wall is 4 m high and supports a cohesive backfill with a unit weight of 17 kN/m3. The shear strength parameters of the soil are cohesion =10 kPa and Ø = 10°. Calculate the total active thrust acting against the wall and the depth to the point of zero lateral pressure
Q9.1 - A 25-m high rock cut with a face angle of 60° has been excavated in a massive, very weak volcanic tuff. A tension crack has opened behind the crest and it is likely that the slope is on the point of failure, that is, the factor of safety is approx imately 1.0. The friction angle of the material is estimated to be 35°, its density is 25kN / (m ^ 3) and the position of the water table is shown on the sketch of the slope (Figure 4). The rock contains no continuous joints dipping out of the face, and the most likely type of failure mode is circular failure. Required- (a) Carry out a back analysis of the failure to determine the limiting value of the cohesion when the factor of safety is 1.0. (b) Using the strength parameters calculated in (a), determine the factor of safety for a completely drained slope. Would drainage of the slope be a feasible method of stabilization? (c) Using the ground water level shown in Figure 4 and the strength parameters calculated in (a), calculate the…
A retaining wall 9 m high supports a cohesionless sandy soil with its face vertical as shown in figure below. Find active earth pressure on the wall , Take Yw = 9.81kN / (m ^ 3)
45.) A retaining wall supports a horizontal backfill that is composed of two types of soil. First layer: 5.91 meters high, Unit weight of 17.26 kN/m3, coefficient of active pressure of 0.291 Second layer: 5.36 meters high, Unit weight of 18.85 kN/m3, coefficient of active pressure of 0.301 Determine the distance of the total active force measured from the bottom of the wall. Round off to three decimal places.
A retaining wall 6 m high supports cohesionless soil having a dry density of 1600 kg/m³, angle of resistance 32 and void ratio of 0.68. The surface of the soil is horizontal and level with the top of the wall. Neglecting wall friction and using Rankine’s formula for active pressure of a cohesionless soil. 1. Determine the nearest value of the total earth thrust on the wall in KN per lineal meter if the soil is dry. a. 73.1 b. 86.7 c. 62.4 d. 98.1 2. Find the nearest value of the thrust on the wall in KN per lineal meter if owing to inadequate drainage, it is waterlogged to a level of 3.5 m below the surface. a. 112 b. 171 c. 147 d. 153 3. Find at what height above the base of the wall the thrust acts during the waterlogged condition. a. 2.21 m b. 2.00 m c. 1.74 m d. 1.42 m