Q.10 Athin cylindrical tube closed at ends is subjectedto internal pressure. A torque is also applied tothe tube. The principal stresses p, and pdeveloped are 80.0 units and 20.0 unitsrespectively. If the yield stress is 240 units, thenwhat is the factor of safety according to maximumshear stress theory?

Answered: Image /qna-images/answer/5232160d-8a1e-40fc-a0d5-ea84f204e09b.jpg

Q.10 Athin cylindrical tube closed at ends is subjected to internal pressure. A torque is also applied to the tube. The principal stresses p, and P2 developed are 80.0 units and 20.0 units respectively. If the yield stress is 240 units, then what is the factor of safety according to maximum shear stress theory?

Q.10 Athin cylindrical tube closed at ends is subjected to internal pressure. A torque is also applied to the tube. The principal stresses p, and P2 developed are 80.0 units and 20.0 units respectively. If the yield stress is 240 units, then what is the factor of safety according to maximum shear stress theory?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem # 4: The tank shown is fabricated from steel plate. Determine the minimum thickness of plate which may be used if the stress is limited to 42 MPa and the internal pressure is 1.5 MPa. USING BOTH TANGENTIAL AND LONGITUDINAL STRESS FORMULA.
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Calculate the maximum shear stress with Mohr's circle? d) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion?
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding.
A WATER TANK IS 5 IN DIAMETER AND 6 HIGH. IF THE TANK IS TOBE COMPLETELY FILLED, DETERMINE THE MINIMUM THICKNESS OF THETANK IF THE STRESS IS LIMITED TO 70 MPa.(note: Diam = 5, Height = 6)
(c): How can the theory be applied to find the maximum allowable shear stress for thick walled cylinders?
The column is constructed from high-strength concrete and eight steel reinforcing rods. If thecolumn is subjected to an axial force of 200 kips, determine the average normal stress in theconcrete and in each rod. Each rod has a diameter of 1 in. ?????? = 30,000 ??? and ????????? =4,000 ???.
A thick cylinder 1 meter inside diameter and 7m long is subjectedto an internal fluid pressure of 40MPa. Determine the thickness of the cylinder ifthe maximum shear stress in the cylinder is not to exceed 65MPa. What will be theincrease in the volume of the cylinder? E=200GPa, μ= 0.30.
): Describe the maximum shear stress theory of failure. (b): Describe the basis of the theory. (c): How can the theory be applied to find the maximum allowable shear stress for thick walled cylinders? (please sent ward form)
Topic: Strema A 750-mm high cylinder carries a load P which produces a normal stress at its cross-sectional area and a shear stress at its lateral surface area. Find its diameter if these stresses are equal. Choices: A. 3.0 m B. 4.5 m C. 1.5 m D. 6.0 m
a) Determine the zero-effort frame by justifying with a table asfollow Joint in equilibrium Nul stress frame .
n figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm wide.(a) if the allowable stresses 200 MPa for bearing in the plate material and 120MPa for shearing of the rivet, determine the minimum thickness of each plate.(b)Under the conditions specified in part (a) what is the largest average stress in the plate. Answer a and b please
2(a): Describe the maximum shear stress theory of failure. (b): Describe the basis of the theory. (c): How can the theory be applied to find the maximum allowable shear stress for thick walled cylinders?