Q.11. A solid steel shaft has to transmit 75 kW at 200 rpm. Taking allowable shearstress as 70 MN/m2. Find suitable diameter for the shaft, if maximum torquetransmitted on each revolution exceeds the mean by 30%.

Answered: Image /qna-images/answer/48ff0297-b0cd-47c6-ac31-3a5032119788.jpg

Q.11. A solid steel shaft has to transmit 75 kW at 200 rpm. Taking allowable shear stress as 70 MN/m². Find suitable diameter for the shaft, if maximum torque transmitted on each revolution exceeds the mean by 30%.

Q.11. A solid steel shaft has to transmit 75 kW at 200 rpm. Taking allowable shear stress as 70 MN/m². Find suitable diameter for the shaft, if maximum torque transmitted on each revolution exceeds the mean by 30%.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: #2 d=37 cm 17 3#8=15cm² = A's -4#11 =40cm² = As fc=280 Kleur fy=4200 kg/au- bw=40cmt Determine pun…

Q: The following contains lines AB, CD, and EF. Complete all views. Label lines that are true length as…

A: To Complete all views of lines AB, CD and EF

Q: D-3 ft Slope = 151. a Concrete Pipe with a diameter of 3ft, longitudinal Slope 1.500, a roughness…

Q: ituation 3. Following are the results of a sieve analysis. Determine: a. Cu b. Cc c. So Sieve No. 4…

A: To Determine :- coefficient of uniformity Cu Coefficient of curvature Cc Sorting coefficient So

Q: Assuming sea water to be incompressible, what is the pressure in tons per square foot 2 miles below…

A: GIVEN- The sea water to be incompressible, Depth below the surface of the ocean = 2 miles The unit…

Q: Analyze each of the following structures. Calculate reaction components, and construct shear and…

Q: A drain carrying 5m³/s of wastewater with its BOD of 100mg/l joins a stream carrying 50 m³/s flow…

A: Given data: Qw=5 m3sQs=50 m3sBODw=100 mglBODs=5 mgl

Q: The hydraulic jack in the figure is filled with two types of oil, the specific gravity of oil 2 is…

A: Given, γoil 2 = 0.80 γoil1 F1 = 2000 lbf

Q: Determine the mass (in kg) of the air in a room whose dimensions are 60 ft x 16 x 10 ft. Assume the…

Q: Specify the type of fabric.

A: Given:- A reverse-air baghouse is to be designed to remove fly ash The power plant exhaust gas…

Q: Internal shear force (V), and internal bending moment (M) at the following locations: qo L3 D B 4 of…

Q: Find the Stress if Tensile force 2.3 N applied on rod having cross sectional area of 1 mm2

Q: The major and minor principal stresses at the point are 3 MPa and -3 MPa respectively. The maximum…

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Q: (6a) A siphon is made of a pipe whose inside diameter is 25.4 mm and is used to maintain a constant…

A: Data given Siphon pipe, diameter = 25.4 mm = 0.0254 m Depth of tank = 6.0975 m

Q: The velocity of a particle along the s-axis is given by v = 15s4/3 where s is in millimeters and v…

Q: Problem 2. Given the following traverse notes for a closed traverse, LINES AB BC CD AZIMUTH 225°…

A: From the given data DMD Method Line Length (l) Azimuth…

Q: 7-14. Determine the normal force, shear force, and moment at a section passing through point D. Take…

Q: Show complete solution. 1. Use Area-Moment Method. El is constant a. b. C. Compute the rotation of…

A: Given data EI = Constant Using Area moment method find. 1. Slope at right end. 2. Maximum…

Q: 34. The data from a closed traverse survey PQRS (run in the clockwise direction) are given in the…

Q: 5. Consider a composite shaft fabricated from a 6 cm-diameter solid aluminum alloy, having G = 28…

A: As per company's guidelines we can only answer first three questions. Kindly post other questions…

Q: A metallic tape which was originally 30 m is found to be 29.79 m long. If the tape is to be used in…

Q: Minimum sizes of doors as prescribed by PD1096, BP 344, RA 9514 and BP220 in the Philippines 1.…

A: Reference : Different codes used in Philippines. Given : A set of codes PD 1096 BP 344 RA 9514 BP…

Q: The measured length of an inclined distance was recorded to be 417.698 m long. The difference in…

Q: Discuss the concept of high-performance concrete. Discuss some of its properties that make it…

A: High-performance concrete (HPC) is concrete that has been engineered to be stronger and more…

Q: (5) (7) 10 kN-m 4m 5 m 10 kN-m + 3 m 6 m (6) (8) 5 m 4 m 10 kN-m 2 kN/m 3 m 6 m

Q: Given the isometric view, provide the top, front, and right-side view

Q: Question 57 For a hydraulically efficient rectangular channel of bed width 5m, the hydraulic radius…

A: Given data: A hydraulically efficient rectangular channel having. Bed width, B = 5 m. Hydraulic…

Q: 3. The transparent "biospheres" beneath the Bay of Noli, in Savona, Italy, are part of the…

A: Fluid pressure : Fluid pressure is a measurement of the force per unit area acting on an item in the…

Q: DETERMINE THE HORIZONTAL VELOCITY, VA OF A TENUS BALL AT A SO THAT IT JUST CLEARS THE NET AT B, ALSO…

Q: Water flows 7 mm deep in a 0.5-m-wide rectangular flume. What would be the percentage error in the…

Q: (a) Is the beam statically determinate or statically indeterminate? If statically indeterminate,…

A: To determine: 1. Statical indeterminacy2. SFD and BMD3. Deflection at the unsupported length

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A: Given,

Q: Comparing PCC with mild steel, answer the following questions:a. Which one is stronger?b. Which one…

A: PCC is known as portland cement concrete.

Q: lar channel one metr . The 300 bed slope al

A: Given data- Discharge (Q) = 1 m³/s Width of rectangular channel (B) = 1m Depth of rectangular…

Q: 3.2 Explain the interrelationship between description and justification of a bridge design.

A: Engineers take into account the various loads, how they are applied, and where they are applied when…

Q: Situation 1 A sample of soil weighing 2.62 kN is removed from a test pit. 1.39 kN of water will just…

Q: If the void ratio of a soil is 0.7, then the porosity of the soil is 00.2 1.2 0.4 1.4 0.5

A: Introduction : The given question is related with geotechnical engineering . In this question data…

Q: Situation 2. A granular soil located in a borrow pit is found to have an in place dry density of…

Q: The major and minor principal stresses at the point are 3 MPa and -3 MPa respectively. The maximum…

Q: H 10' G B F₁ 10' F₂ 10' D 10' F,

Q: Over a basin of area 333 km², there was a storm for 6 h with a uniform intensity of 2 cm/h. The…

A: Given- Basin Area A=333 km2, 6 h storm, Intensity I=2 cm/h, Runoff- R=20×106 m3,

Q: View Policies Current Attempt in Progress Replace the three forces shown by an equivalent…

Q: The surface area

A: Given data, Total flow, Q= 9600 m3/d Solid concetration,C= 3000 mg/l Clarifier required to…

Q: Problem For the frame shown, design the maximum permissible value of P with a factor of safety of…

Q: Determine the magnitude of the moment of the force F = {50i - 26 j - 80k} N about the base line BC…

A: Given : F = { 50i - 26j - 80k} N Determine the magnitude of moment of force F ?

Q: 2- Analyze the beam shown below due to the applied loads, a settlement of B of 1.2" and an initial…

A: Given data : Settlement at b = 1.2'' , Rotation at d = 0.8 degrees CW = 0.8×π180 = 0.013962 radians.…

Q: thin walled tube with an internal diameter of 35 cm and a wall thickness of 6 mm is subjected to an…

Q: oil borings made at a site in city indicate that the top 6 m is a loose sand and miscellaneous fill,…

A: According to given data Soil borings made at a site in city indicate that the top 6 m is a loose…

Q: Given the isometric view, provide the top, front, and right-side view

Q: A granular soil located in a borrow pit is found to have an in place dry density of 1895 kg/m^3. In…

A: In soils without cohesion, relative density refers to the ratio of void ratios in their loosest and…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

Q.11. A solid steel shaft has to transmit 75 kW at 200 rpm. Taking allowable shear
stress as 70 MN/m2. Find suitable diameter for the shaft, if maximum torque
transmitted on each revolution exceeds the mean by 30%.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A shaft ABC of 500 mm length and 40 mm external diameter is bored for a part of its length AB, to a 20 mm diameter and for the remaining length BC, to a 30 mm diameter bore. If the shear stress is not to exceed 80 N/mm², find the maximum power, the shaft can transmit at a speed of 200 rpm. [The shear modulus is 80 GPa]. If the angle of twist in the length of 20 mm diameter bore is equal to that in the length of 30 mm diameter bore, find the lengths of the shaft that has been bored to 20 mm and 30 mm diameter. Also determine the total angle of twist.
The solid spindle AB has a diameter d,=38mm and is made of a steel with an allowable shearing stress of 84 MPa, while sleeve CD (hollow cylinder with an outer diameter of 75mm and a thickness of 6mm) is made of a brass with an allowable shearing stress of 50 MPa. Determine the largest torque T that can be applied at A. 100 inm 200 min 1-6 ma B 75 man
4) A 4m solid core steel shaft with 50 mm diameter is fixed at its ends. It is subjected to a 400 N-m torque 1m from the left end and a 100 N-m torque 0.5 m from the right end (same direction).
For the transmission tower shown below. Determine the following (Use any method in solving) 1. Axial Force at Member HK 2. Axial Force at Member AD
2. The shaft shown has the following properties: Inner diameter, in inches SET Outer diameter, in inches Tallow in ksi A 6 10 Determine the maximum torque that can be transmitted by (a) the shaft as designed, (b) a solid shaft of the same weight, and (c) a hollow shaft of the same weight and an 8-in. outer diameter. T' 4 in. 6 in. 8 ft
2. For the system shown below, compute the maximum torque it can accommodate if a is 2000mm and b is 150omm. Assume that the bronze segment, has a diameter of o.o75m, t < 60 MPa, and G = 35x10^3 MPa. On the other hand, assume the steel segment has a diameter of 0.05m, t < 80 MPa, and G = 83x10^3 MPa. b A
Problem (1): Determine the internal torque in shaft (3) 50 N-m 28 N-m 21 N-m 14 N-m (1) (2) (3) Determine the internal torque in shaft (3).
Two solid steel shafts (shafts) in the figureconnected with gears. Permission for steel shaftsthe permissible shear stress is 7000 psi. BC spindle1.6 in diameter and 1.25 in diameter of EF shaftit is known that the width applied to the shaft at the C pointCalculate the large TC torque.
A drive shaft running at 2500 rpm has outer diameter of 80mm and inner diameter of 60mm. The allowable shear stress in the shaft is 40MP.. Determine the maximum power that can be applied.
Q.11. A solid steel shaft has to transmit 75 kW at 200 rpm. Taking allowable shear stress as 70 MN/m2. Find suitable diameter for the shaft, if maximum torque transmitted on each revolution exceeds the mean by 30%.
60 mm 2) 30 mm- A torque T = 3 kN · m is applied to the solid bronze cylinder shown. Determine (a) the maximum shearing stress, (b) the shearing stress at point D which lies on a 15-mm-radius circle drawn on the end of the cylinder, (c) the percent of the torque carried by the portion of the cylinder within the 15-mm radius. D. 200 min T = 3 kN - m
The A-36 solid steel shaft is 2 m long and has a diameter of 65mm. It is required to transmit 60kW of power from the motor M to the pump P. Determine the smallest angular velocity the shaft in radian per seconds that can have if the allowable shear stress is 80 MPa.