Q.2 A bipolar transistor shown in the figure below is used as a Chopper Switch with a frequency of fs = 30 kHz. The DC input voltage of the chopper is Vs = X Volts and load current IL = Y Amperes. Where X = last three digits of your Roll Number and Y = first three digits of your Roll Number. The switching times are tr= 1µs and tr= 5µs. Determine the values of a) Ls b) Cs c) Rs for critically damped condition

Q.2 A bipolar transistor shown in the figure below is used as a Chopper Switch with a frequency of fs = 30 kHz. The DC input voltage of the chopper is Vs = X Volts and load current IL = Y Amperes. Where X = last three digits of your Roll Number and Y = first three digits of your Roll Number. The switching times are tr= 1µs and tr= 5µs. Determine the values of a) Ls b) Cs c) Rs for critically damped condition

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If a sinusoidal voltage is applied to the base of a biased npn transistor and the resulting sinusoidal collector voltage is cut to near zero volts, what is the state of the transistor? Please select one: a. answers B and C b. interrupted drive c. answers A and C d. forced into nonlinear operation e. drifting into saturation
During turn-on and turn-off of a power transistor, thecurrent-time and voltage-time relationships are asshown in the adjacent figure. Observe the waveformsand calculate,40) the OFF-state power dissipation (static);41) the switch ON-state power dissipation(static);42) the average switching loss for the OFFtransition (dynamic);43) the average switching loss for the ONtransition (dynamic);Assume a switching frequency of 2kHz with 397V as specified in Appendix A.
2. A load of 8Ω is supplied by a single-switch Direct Current (DC) chopper with an inputvoltage of 40V. The switching frequency is 800Hz, the duty ratio is 0.4, and thetransmission voltage drop of the transistor is 2.4V a. Draw the chopper circuit presented in the question b. Find the switching period with the duty time of BJT c. Draw the load voltage, load current, BJT current, BJT voltage along two periods d. Find the output voltage. Is the achieved load voltage the average value or the effectivevalue e. Find the output power f. Find the average value and effective value of BJT current g. Find the power loss of BJT h. Find the DC source current i. Find the circuit efficiency
In the Boost DA-DA circuit:Source voltage (E) value: in the range of [17-29] (volts),Switching frequency (f) value: 20 khz,Voltage between load ends: 40VCapacitance value: 470uFPower dissipated at load: 10 watts What is the lowest inductance L, in uH, that can keep the DC-DC converter in continuous current under these conditions? a) 269.3731 b) 415.4375 c) 364.8204 d) 163.6472 e) 578.1875
During turn-on and turn-off of a power transistor, the current-time and voltage-time relationships are as shown in the adjacent figure. Observe the waveforms and calculate, 44) the OFF-state power dissipation (static); 45) the switch ON-state power dissipation (static); 46) the average switching loss for the OFF transition (dynamic); 47) the average switching loss for the ON transition (dynamic); Assume a switching frequency of 1kHz with 437V.
During turn-on and turn-off of a power transistor, the current-time and voltage-time relationships are as shown in the adjacent figure. Observe the waveforms and calculate: 44) the OFF-state power dissipation (static); 45) the switch ON-state power dissipation (static); 46) the average switching loss for the OFF transition (dynamic); Assume a switching frequency of 1kHz with Vx =339V
(i) With neat sketch explain the cross sectional view and I-V characteristics of the device which is used in low on state loss and small switching frequency operations. (ii) Write FOUR demerits of the above mentioned power semiconductor device.
Graphs of the switching characteristics of the power transistor are given in the figure. Collector-emitter leakage current I ceo = 2.8mA. Find the power consumption depending on the collector current accordingly. a) Transmission time b) During transmission
A) What does VCO stand four? Show by drawing the relationship between its input and output signals. Compare VCO circuit with LC Tank circuit in terms of circuit functionality and how the output is generated in each of them. B) Compare between AM and FM in terms of noise immunity, interference, equipment complexity and cost and line of site transmission.
It is requested to determine the operating point of the transistor by drawing the DC load line. (B-125) Which is the ICQ value?
Q3) An FM modulator has a constant frequency deviation of 4KHz / volt. Determine the maximum amplitude of the information that should be given to the modulator input. If desired, the amount of FM spectrum produced by the modulator is 11 for the information frequency of 5 KHz.
1) Explain the Voltmeter PMMC instrument and the Ammeter PMMC instrument in AC?2) What are the benefits of using an Auto Transformer instrument in AC?