Q.2: Draw any seven steel structure’s shapes, also mention its appropriate names.

Q: Differentiate between the following:…

A: slab - its the flat plate element in the building having some thickness to resist the moment and…

Q: Draw and define the following terms; 1. Wood 2. Lumber 3. Rough Lumber 4. S2s and S4s 5. Slab…

A: As per the guideline, I am answering 1st three subparts please upload it again to get the other…

Q: 14. Which of the following is defined at the uppermost part of the building which is constructed in…

A: Uppermost part of the building which is constructed in the form of a framework to give protection to…

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+1+1=5

Q: identify  the different structural parts of a two story house and illustrate with labeling in an…

A:

Q: Determine the tributary widths and tributary areas of the joists, beams, girders, and columns in the…

A: Given:- 9" overhaang (typ.)X direction= 32'-0"Y direction=24;-0"To find:-a) tributary…

Q: A 4 meter column is having a dimension of 30cm by 30cm. Estimate the total weight in kg of the…

A:

Q: ) = 1.50 ksi. Determine the dimension of the timber. if it is rectangular a D-width ratio of 1.5.…

A:

Q: Define Shear Strength

A: Definition; Shear strength is the strength of a material or component against the type of yield or…

Q: Find the centroid of the area of a trapezoid that has two equal slantig sides, a 12in base and a 6in…

A: To determine the centroid of the area formed by at trapezoid of given dimensions.   Given a…

Q: Differentiate between the following by drawing neat sketches, also accompany the figures with the…

A:

Q: About staad. Draw how you will place a C-purlin on a rafter or top chord of a truss as you will…

A: Introduction : Roof trusses are distinguished by their efficient use of building materials (timber,…

Q: Given problem: A built-up wooden beam section is made of two 56 mm x 104 mm sections glued on the…

A: Given Data:Beam section 56mm×104mmTo find Area of beam sectionand Distance of the centroid from top…

Q: Calculate the stresses that will occur in the pipe for the water pipe buried 5 meters into the…

A: Height of the pipe under pipe = h = 5m

Q: If soft steel railroad rails are laid at 10°C, what space should be left between them if they are…

A: Solution:

Q: Determine the force acting on members BE, FH, and HK. . Final answer must be rounded to the nearest…

A: Determine the force acting on members BE, FH, and HK.

Q: An interior wall of a building is made up of metal studs with 5/8 in. wallboard on each side.  See…

A: Given: Width of the metal studs=58inWidth of the stud=338inThen,Width of metal studs 58in on both…

Q: Calculate the bending and shear stresses at point F on the Section B-B.

A:

Q: A piece of wood 1 ft. square and 10 ft. long, weighing 40 lb per cu. Ft, is submerged vertically in…

A:

Q: Problem 10. DETERMINE THE DIMENSION FOR THE PLYWOOD BOX BEAM FIGURE SHOWN. y = A1 = 21 x 4.5 41 = A₂…

A: Given data:- The expression Area A1=21X4.5 The expression Area A2=(21-6)×3.5=15×3.5

Q: Three boards, each 2 in. thick, are nailed together to form a beam that is subjected to a shear. If…

A: Given: The thickness of the board is 2 in. The allowable shearing force in each nail is 198 lb. The…

Q: What is the radius of gyration of the built-up structural member with respect to the X centroidal…

A:

Q: piece of wood floats in water with 15cm projecting above the water surface. When placed in oil, the…

A:

Q: 1. Section modulus for a rectangular section is given as (a) bd/36 OT (b) bd/6 (c) bd/6 (d) bd/12

A: Correct answer is option C bd2/6

Q: Q2/ Answer the followings with drawing sketch: A/ briefly explain what is construction joint and…

A: Construction Joint: It is type of concrete joint that is used when a new section of concrete is…

Q: The framing plan of a two-storey post tensioned structure is shown below. Due to some issues, the…

A: The given values are as follows,The size of tge square colunm =0.50by…

Q: Draw the load, shear and moment diagram for each beams. Include the magnitude, distances and other…

A:

Q: Identify the superstructure and substructure components of a building. Use 3 storey building for…

A:

Q: Determine the estimated weight of an A-36 steel plate size 3/16” x 6” x 20

A: Given data in question  A-36 steel Plate size To find out  Weight of A-36 steel   Density of A-36…

Q: Describe each of the structural steel designations listed below:   a. W 14 x 82   b. MC 12 x 45…

A: All the structural steel designations are as per American Codes a. W 14 x 82 Answer:- The structural…

Q: 42. How many square feet of forms are needed to construct the columns shown in Figures 5-26 and 5-…

A: Consider the footing placement as in Figure (1).

Q: Determine if w10x12 (A242) section is Compact, Non-Compact or slender. Show neat handwriting and…

A:

Q: Find the ∑ fy in the given figure below, consisting of a beam with various sections

A: Above given diagram we have to find sum of forces in y direction

Q: Should one way slab be used for Steel Deck if the slab is a Square

A: Yes. Generally that is true.   The beauty of steel structures lie behind the short construction…

Q: Q2) For the shown beam, calculate beam web yielding capacity? 1-178X102X19 1-305 X 127 X 37

A: b (Width of section on top of beam) = 101.8mm

Q: Design strength based on gross area (kips ) Design strength based on net area (kips).

A: Answered only 1 question Find the design strength

Q: Determine internal indeterminacy

A: Given data : Number of member (m)=3 Number of external support reaction (R)=2+1+1+2=6 Number of…

Q: Q/Figure No. 5 shows a plan of a ground floor structural building consisting of columns and beams…

A: For the given plan, before planting a new column the existing column B and C will be discontinued by…

Q: uestion: Identify and discover the different structural parts of a two-storey house and illustrate…

A:

Q: Can someone explain where the 32.2 is coming from please

A: Question: where the 32.2 is coming

Q: c) Discuss the grading of timber for structural purposes in civil and construction engineering

A: Structural grading is the process of sorting the timber on the basis of estimates of the structural…

Q: Determine the form factors for the timber beams of following shapes (b) Also, compare their load…

A:

Q: Q2) For the shown beam, calculate beam web yielding capacity? I-178X102X19 1-305 X 127 X 37

A: b (width of section on beam) = 101.8mm

Q: 1.Determine the Style in its diagram 6 KN 12 m 12 m 12 m D A

A: Free body diagram -  Force in the vertical direction -  ∑FY = 0RA + RC = 6        .........1 Fixed…

Q: ▼ Determine the vertical support force at A. Express your answer to two significant figures and…

A: Given,  Mass of the uniform steel beam, M= 360 kg The vertical forces acting on the supports are FA…

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.