Q.3 A level circuit is shown in figure. The survey, needed for local engineering commenced at BM 35, the elevation of new benchmarks 36, 37, 38 and 39 were determined, and then the level survey was looped back to BM 35, the point of commencement. Fined the adjusted new BMs. project, ВМ 35 35 Elevation(m) 119.010(fixed) 123.342 35 118.933 36 37 38 39 118.206 118.451 120.491 HM 36 09 kn- DM 35 O km DUM 37 06 km BM 39 вм за 0.7 km

Q.3 A level circuit is shown in figure. The survey, needed for local engineering commenced at BM 35, the elevation of new benchmarks 36, 37, 38 and 39 were determined, and then the level survey was looped back to BM 35, the point of commencement. Fined the adjusted new BMs. project, ВМ 35 35 Elevation(m) 119.010(fixed) 123.342 35 118.933 36 37 38 39 118.206 118.451 120.491 HM 36 09 kn- DM 35 O km DUM 37 06 km BM 39 вм за 0.7 km

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following readings were observed successively with a leveling instrument. The instrument was shifted after the fifth and eleventh readings.0.485, 1.210, 1.635, 3.395, 3.775, 0.650, 1.400, 1.795, 2.575, 3.375, 3.895, 1.735, 0.635, 1.605 mDetermine the R.L of various points and show the entries in a level book, if the R.L of the first point is 100m, using the rise and fall method.
Q - The subsequent readings were curious about dumpy level with four.zero m leveling team of workers and 20.0 m c program languageperiod. 1.755, 2.505, 3.050, 3.950, 1.750, 2.355, 3.a hundred, three.805, zero.905, 2.0.5 and 3.250. If R.L of first point is 15.zero m. Calculate the R.L of different points by way of H.I approach.
Three triangulation stations A, C and E are points on the shore whose position were observedfrom X. The angles were measured using a sextant from the boat at X to the three triangulationstations. The following data were recorded during the survey procedure:Distance AC = 700mDistance CE = 680mAngle ACE = 148oAngle AXC = 45oAngle CXE = 35oAngle CAX = 70oDraw the diagrama.) Compute the angle CEX.b.) Compute the distance AX.c.) Compute the distance XE.
Lines of levels were run requiring n instrument setups. If the rod reading for each backsight and foresight has a standard deviation s, what is the standard deviation in each of the following level lines?(a) n = 15, s = ±0.015 ft(b) n = 28, s = ±5 mm
0 a 2178 kN O b. 3726 kN 1| select one: WG o weiox92
Figure 3 shows staff readings obtained from a survey along the centerline of the road.The levelling commenced on TBM1 (23.832 m AOD) to TBM2 (24.082 m AOD) andthe reading were taken at 25 m intervals along the line. Calculate the reduce level ofall the chainage points. Apply the arithmetic checking.
Find the Reduced Level (R.L.) of each station? (Use Rise and Fall Method only) Stations Readings R.L. (ft.) Remarks B.S. (ft.) I.S. (ft.) F.S. (ft.) A 4.320 007 B.M. B 3.352 C 3.000 D 1.586 2.367 C.P. E 2.490 F 3.612 G 4.012
The following readings were successively taken in levelling work 2.230, 1.605, 0.990, 2.090, 2.865 level instrument was shifted after 3rd reading. If R.L of first station 100.000 m, the R.L of other stations will be Option 1: 100.625, 101.240, 100.140 Option 2: 101.605, 100.990, 102.090, 100.865 Option 3: 100.230, 100.625, 101.240, 100.465 Option 4: 100.625, 101.240, 100.465
The following consecutive readings were taken with a level and a 4mt. leveling staff on acontinuously sloping ground at common intervals of 30 m:0.855(onA),1.545,2.335,3.115,3.825,0.455,1.380,2.055,2.855,3.455,0.585,1.015,1.850,2.755,3.845(on B)Enter the readings on a level field book and work out the staff readings on that, Find theR.L of different points using Collimation Plane Method. RL of the BM is 200.000m.Calculate the slope of the ground.
Hi! Help me with this please. Thank you so much! A dumpy level is set up at one end of a line 160m. long for the purpose of determining the instrument stadia interval factor. The line is marked by hubs at every 40 m. and a stadia rod is held at each hub. The stadia intercept at each location of the rod were observed as follows: 0.402, 0.813, 1.231, 1.602 respectively. Compute the average value of the stadia interval factor. Height of instrument is 1.5m.
Answers a) 0.436 b) 17.44 kPa c) 31.98 kPa d) 3.57 kN/m3
plz, solve this question, it is not graded question It is Surveying-2 Regno : 5395