Q.3.A. Develop an expression for the distance traveled by a freely falling body using the dimensional method. Assuming the distance depends upon the weight of the body with the acceleration of gravity and the time. B. Evaluate the followings: Steady flow, Two dimensional flow, Uniform flow, Turbulent flow, Laminar flow.

Q.3.A. Develop an expression for the distance traveled by a freely falling body using the dimensional method. Assuming the distance depends upon the weight of the body with the acceleration of gravity and the time. B. Evaluate the followings: Steady flow, Two dimensional flow, Uniform flow, Turbulent flow, Laminar flow.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 49P

See similar textbooks

Similar questions

please find the flow rate and flow velocity which is represented by Q
A block in the following figure is pulled up with a Force 20 +S Nt. The weight of the block is 10 Nt. The area of the contact surface between the block and fluid is 10 cm2. a)find the velocity of the block if the fluid is an ideal fluid b)find the velocity of the block if dynamic viscosity of the Fluid between the block and inclined surface in the figure is 0.2 Nt.s/m2. (S=4)
Stokes law can be used to determine the viscosity of a fluid by dropping a spherical object in it and measuring the terminal velocity of the object in that fluid. This can be done by plotting the distance traveled against time and observing when the curve becomes linear. During such an experiment a 3-mm-diameter glass ball (? = 2500 kg/m3) is dropped into a fluid whose density is 875 kg/m3, and the terminal velocity is measured to be 0.15 m/s. Disregarding the wall effects, determine the viscosity of the fluid.
A cylinder falls down the inside of an oil-filled pipe as shown. The small space between the pipe and cylinder is lubricated with a film of oil with a viscosity mu. Derive a formula for the steady state rate of descent of the cylinder with weight, W, diameter, d, and length, l, slinding inside the vertical smooth pipe with diameter, D. Assume the cylinder is concentric with the pipe as it falls. Use the general formula to find the rate of descent of a cylinder 100mm in diameter that slides inside a 100.5mm inside diameter pipe. The cylinder is 200mm long and weights 15N. The lubricant is SAE 20W oil at 10oC.
Consider laminar flow of a Newtonian fluid in the y direction between two parallel andvertical plates with a distance between h, at steady state. The plate on the left isstationery and the other plate on right-hand side is moving vertically upwards at aconstant velocity Vo. Derive an equation for the velocity profile.
! Use the Given Data in Solving ! Rectilinear Motion: A particle travels in v = (12 - 3t^2) m/s, where t is in seconds. When t = 1 s, the particle is located 32.8 ft to the left of the origin. Determine the displacement (m) from t = 0 t = 10 s, and the distance (m) the particle travels during this time period.
Consider the two-dimensional flow of an inviscid, incompressible fluid described by the superposition of a parallel flow of velocity V0, a source of strength q, and a sink of strength −q, separated by a distance b in the direction of the parallel flow, the source being upstream of the sink. (a) Find the resultant stream function and velocity potential. (b) Sketch the streamline pattern. (c) Find the location of the upstream stagnation point relative to the source.
Fluid mechanics- Bernoulli's Equation along a streamline: The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure tap at station 1. The velocity at station 2 is twice that at station 1. Air with a density of 1.2kg/m3 flow through the duct. A water manometer is connected between the stagnation probe and the pressure tap, and a deflection of 10cm is measured. What is the velocity at station 2?
Given the acceleration-time diagram sketch the velocity-time diagram and determine the displacement at time=9s.
Derive the equation that connects the pressure difference to the average velocity for a fluid to flow in a stratified flow regime between two plates with lengths L and distances b.
A manometer is used to measure the pressure difference between points A and B in a pipe as shown. Water flows in the pipe, and the specific gravity of the manometer fluid is 3.0. The distances and manometer deflection are indicated on the figure. Find (a) the pressure differences and (b) the difference in Piezometric Pressure, (c) the difference in Piezometric head. Express both answers in kPa.
Fluid Mechanics question: A device used for measuring the specific weight of a liquid consists of a u-tube manometer as shown. The manometer tube has an internal diameter of 0.5 cm and originally has water in it. Exactly 2 cm3 of unknown liquid is poured into one leg of the manometer, and a displacement of 5cm is measured between the surfaces as shown. What is the specific weight of the unknown liquid?