Q.4 A temperature sensor has a resistance of 100N at 0°C. If the temperature coefficient of the sensor is 0.042/°C: (a) what is the sensor resistance at 220°C. (b) if the sensor has an uncertainty of 5% what is the range of the resistance at 220°C. (c) a signal conditioning circuit is used to represent the resistance change as a voltage change with a transfer function 5mV/N ±2%. What is the output voltage range at 220°C.

Q.4 A temperature sensor has a resistance of 100N at 0°C. If the temperature coefficient of the sensor is 0.042/°C: (a) what is the sensor resistance at 220°C. (b) if the sensor has an uncertainty of 5% what is the range of the resistance at 220°C. (c) a signal conditioning circuit is used to represent the resistance change as a voltage change with a transfer function 5mV/N ±2%. What is the output voltage range at 220°C.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please assist with question 3, details on how to do. Thank you. Check image for Q3 3. Figure shows a PCM signal in which the amplitude levels of volt and volt are used to represent binary symbols 1 and 0, respectively. The code word used consists of three bits. Find the sampled version of an analog signal from which this PCM signal is derived.
2. a) Design a 9v DC oscillator circuit that produces a frequency of 500 Hz. The circuit may use a 555 timer or two transistor design(s). Show all calculations including the DC currents and bias voltages. Include the schematic and the required frequency formula(s). b) As a bonus, if a larger load were required to be connected to the chip, how would the schematic look and what components would be used to do design it? Also, as a theoretical approximation, if the 9v battery had a rating of 4 amp-hours, how long would it last powering this circuit? Show calculations to illustrate how you arrived at the answer.
Without writing or drawing tools to lean on, you must use words, not equations, graphs or schematics in your explanation. The current in a differential pair of transistors swings between the two sides of the transistor pair as the input voltage swings between the inputs. The output voltages of course follow the current inversely. Is this swing of current related to one of the chief advantages of differential operation, the elimination of common mode signals? Keep in mind, there is a restricted range of allowed current (and voltage) swing to keep the amplifier operating in a linear way
Ex. 1780. A closed-loop system has sustained oscillations (i.e. constant amplitude) with a period of 85 seconds when the gains are: proportional=96, integral=0, and derivative=0. Determine the ideal- PID gains Kp, Ki (minutes^-1), Kd (minutes) using the Ziegler-Nichols method. Also determine the standard-PID values which are commonly used in industry, such as LabVIEW: Kc, Ti (min), Td (min). ans:6
An equivalent circuit for a piezoelectric accelerometer, which uses a quartz crystal as the sensing element, is shown in the following figure. The generated charge is denoted by q and the output voltage at the end of the accelerometer cable is vo. The piezoelectric sensor capacitance is modeled by Cp and the overall capacitance experienced at the sensor output, whose primary contribution is due to cable capacitance, is denoted by Cc. The resistance of the electric insulation in the accelerometer is denoted by R. Write a differential equation relating vo to q. What is the corresponding transfer function? Using this result, show that the accuracy of the accelerometer improves when the sensor time constant is large and when the frequency of the measured acceleration is high. For a quartz crystal sensor with R = 1 × 1011 Ω and Cp = 300 pF, and a circuit with Cc = 700 pF, compute the time constant.
Using 741 op amp, design a suitable circuit to generate Binary Phase Shift Keyiing(BFSK) modulator. Design should perform in such a way that the BFSK output should contain a frequency of f1=2kHz when message signal is low and f2 =4kHz when the message signal is high. Take the frequency of message signal as 200Hz. Draw the clear circuit diagram and calculate the values of resistors and capacitors used.
1. Consider the state space system with the given picture. Is this a valid state-space system? 2. (sperate problame0 Write down a transfer function of a stable system for which pure proportional feedback could drive the system unstable.
Assume that the value of RC is equal to 5900 Find the operation region of the BJT. Show all your work and explain your reasonings.
source signal is sampled, quantized, and encoded into PCM with pulse shaping. The corresponding information rate of the PCM signal is 2 kHz. The maximum permissible source bandwidth, the 6-dB bandwidth and the transmission bandwidth are found to be 1 kHz, 3 kHz and 6 kHz, respectively. (i) The rolloff factor of the pulse shaping. (ii) The number of possible levels that can be taken by the information pulses. (iii) The number of quantization levels of the PCM quantizer. Please solve all parts otherwise down vote
A 5-V, 10-MHz oscillator have a rise/falltime of 10ns and a 50% duty cycle is applied to a gate. Determine the value of the capacitance such that the 5th harmonic is reduced by 20 dB in the gate voltage Vg(t).
Q: Find the digital equivalent and the resolution for a 3 bit DAC using Successive Approximation of Vin = 0.4 V and Vref = 1 V?
Of the four circuits shown, which tend to provide a high output resistance? (b) Which provide a relatively low output resistance?