Q1: A (230/230) V, 3 KVA single phase transformer gave the following data O.C. test : 230 V , 2 amp. , 100 W S.C. test : 15 V , 13 amp. , 120 W Determined regulation and efficiency at full load , 0.8 p.f. laggig.

Q1: A (230/230) V, 3 KVA single phase transformer gave the following data O.C. test : 230 V , 2 amp. , 100 W S.C. test : 15 V , 13 amp. , 120 W Determined regulation and efficiency at full load , 0.8 p.f. laggig.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11P: For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power...

See similar textbooks

Related questions

Q: A 10kVA, 200/400V 50Hz single-phase transformer gave the following test results. O/C test: 200V,…

A: The solution is as follows.

Q: A 240/60 V, single-phase, ideal transformer is to supply power to a load rated at 90 V, 60 Hz. What…

Q: What would be the ratings (voltages and currents) and turns ratio of a three-phase transformer to…

A: The solution is given below

Q: Q2/ In No-load test of single -phase transformer, the following test data were obtained: Primary…

A: The formulae used are given below.

Q: Q1) I. A 100 kVA, three-phase ideal transformer has 4950 turns on the pr imary and 180 turns on the…

A: As per Bartleby guidelines we are allowed to solve only one question with maximum three subparts,…

Q: 13. A 60 kVA, 2300/230 volt, 60-cycle transformer is tested in the laboratory so that its…

Q: (b) A three phase distribution transformer characteristics is shown in Table Q1(b). Referring to…

A: Formula to calculate efficiency of a transformer is: η=n×KVA×cosϕn×KVA×cosϕ+Pi+n2×PCUwhere, n is…

Q: (i) Sketch the single line diagram symbol for generator and two windings transformer. (ii) Describe…

A: There are two types of configuration possible in the three phase system based on the number of…

Q: Q/ A 10-kVA, 440/3300-V, 1-phase transformer, when tested on open circuit, gave the following…

Q: 18. A short-circuit test was performed upon a 10-kva 2,300/230-volt transformer with the following…

A: A transformer is an electrical machine which is used in AC circuit to either step up or step down…

Q: Q1) I. A 100 kVA, three-phase ideal transformer has 4950 turns on the pr imary and 180 turns on the…

A: In this question, 100kVA, 3 phase ideal transformer Number of turn in primary side N1 = 4950…

Q: 19. The following data were obtained from a short-circuit test performed upon 50-kva 2,300/115-volt…

Q: Q2/ In No-load test of single-phase transformer, the following test data were obtained: Primary…

A: Single phase transformer test performance Primary voltage 220V , secondary voltage 110V Primary…

Q: 4. A 10-kVA, 440/3300-V, 1-phase transformer, when tested on open circuit, gave the following…

Q: A 300 kVA, 12,000 : 4000 V, 60 Hz transformer has open-circuit test readings: 4000V, 1.1 A, 2000 W,…

Q: A 3300/300 V single phase transformer gives 0.6 A and 60 W as ammeter and wattmeter readings when…

A: Given, at No load Ammeter reads, Io=0.6 A Wattmeter reads, Poc=60 W Supply given to the low voltage…

Q: A 10-kVA, single-phase transformer has its primary connected to a 2000-V supply. It has 60 turns on…

Q: Q1) I. A 100 kVA, three-phase ideal transformer has 4950 turns on the pr imary and 180 turns on the…

A: As per Bartleby guidelines we are allowed to solve only one question with maximum three subparts,…

Q: Q1) A 22 kVA, 2200/220 V, 50 Hz single-phase transformer's low voltage side is short-circuited and…

Q: Solve the following problems with complete solutions and units using two(2) decimal digits. 3. A…

A: The solution is given below

Q: A 500-kVA, 3-phase, 50-Hz transformer has a voltage ratio (line voltages) of 33/11-kV and is…

A: Given data, KVA rating S = 500 KVA Voltage rating 33/11 KVA Resistance at high voltage side R1=35 Ω…

Q: Q. A single phase transformer has 350 primary and 1,050 secondary turns. The net cross-sectional…

Q: Question # 1: The equivalent circuit impedances of a 20 kVA, 8000/240 V, 60 Hz transformer are to be…

A: In this question we need to find a equivalent circuit impedance of the given transformer.

Q: 7. The following data were obtained when a 25 kVA, 2300/460 V, 50 Hz transformer was subjected to…

Q: Data obtained from short circuit and open circuit tests of a 75-kVA, 4600-230 V, 60 Hz transformer…

A: Open circuit test The power factor is PF=cosϕ=POCVOC×IOC=52230×13.04=0.017 lagging The admittance is…

Q: A single phase transformer on open circuit condition gave the following test results: Applied…

A: From the question, it is given that Applied voltage Frequency Power drawn 192 V 40 Hz…

Q: A single-phase transformer on open-circuit condition gave the following test results: Applied…

A: For constant V/F operation on transformer Hysteresis loss directly proportional to frequency Eddy…

Q: Problem 2 A 23-kVA, 2300/230-V, 60-Hz, step down transformer has the following resistance and…

Q: 5 kVA, 220/110 volts single-phase transformer was tested and has the following results. At…

A: A short test is performed on the transformer to find net copper loss in the transformer winding.…

Q: A 1.5-kVA 240/120-volt single-phase transformer is serving a 10-ohm load connected at the…

A: Transformer is a static device which is used to step up or down the voltage level or current level…

Q: A 5000-kVA 230/13.8-kV single-phase power transformer has a per-unit resistance of 1 percent and a…

A: (a) The open-circuit test was performed on the low-voltage side of the transformer, so it can be…

Q: In the Open-circuit test of the transformer (OC TEST), wattmeter measures 2 kW, in the short-circuit…

A: Given POC =2 KWPSC =200 KW

Q: 1.10. QUESTIONS AND DISCUSSION: 1. A transformer is rated at 440/115 V and volt-ampere at 50HZ.…

A: Disclaimer: Since you have asked multiple questions, we will solve the first question for you. If…

Q: Q2- A 3-phase 250KVA, 11000/416 transformer is delta-connected on the primary and star connected on…

A: In the question following data is given 3 phase 250KVA 11000/416 delta/star connnected transformer…

Q: Given a transformer connected to a constant pressure system at a frequency of 60 cycles, would the…

Q: A 100-KVA, 230-V/115-V, 60-Hz transformer was tested with the following results: Short-circuit test:…

Q: A 10-kVA, 440/3300-V, 1-phase transformer, when tested on open circuit, gave the following figures…

Q: A transformer supplies 10A at 390 V into a resistive load. The transformer’s Volt-Ampere rating is?

A: we need to find out transformer’s Volt-Ampere rating.

Q: A 240/60 V, single-phase, ideal transformer is to supply power to a load rated at 90V, 60hz. What…

Q: A 40-kVA transformer has iron loss of 450 W and full-load Copper loss of 850 W. If the power factor…

A: Given, kVA rating of transformer, S=40 kVA Iron loss, Pi=450 W Copper loss, Pcu=850 W Power factor,…

Q: Q1) The equivalent circuit impedances of a 20-kVA, 8000/240 V, 60-Hz transformer are to be…

Q: -The efficiency of a 200 KVA , single phase transformer is 98% when operating at full load 0.8…

A: To determine the full load copper loss and half load efficiency of a single phase transformer.…

Q: The efficiency of a 20 kVA 15.4 / 0.4 kV three-phase power transformer is 73% for a load with unity…

Q: A single-phase transformer rated 65 KVA is connected to 400/235 V,50HZ supply, has an efficiency of…

A: The solution can be achieved as follows.

Q: Three transformers, are connected delta on the primary side and Wye on the secondary side, step the…

Q: A short-circuit test was performed upon a 10-kVA 2,300/230-volt transformer with the following…

Q: A 5-kVA 480/120-V single-phase transformer is equipped with high-voltage taps so that it may be…

A: The transformer is a constant power device, that means the power on the high voltage side is always…

Q: A 10 kVA, 1000/250 V transformer is to be tested to determine its equivalent circuit parameters. The…

A: 10KVA transformer 2000/250V Open and short circuit parameters Given Equivalent circuit? Copper…

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

100%

Q1:
A (230/230) V, 3 KVA single phase transformer gave the following data
O.C. test : 230 V , 2 amp. , 100 W
S.C. test : 15 V , 13 amp. , 120 W
Determined regulation and efficiency at full load , 0.8 p.f. laggig.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
The efficiency of a 20 kVA 15.4 / 0.4 kV three-phase power transformer is 79.1% for a load with unit power factor at rated power. Transformer Relative short circuit voltage% Uk = 30.0 and relative idle current% I0 = 30. Since the transformer is connected star-delta; Note: In 3-phase electrical machines, the current-voltage information given on the label is always line values. Phase value When given, it must be specified separately. Therefore, all current-voltage information given in the question are line values. 1-Draw the primary reduced equivalent circuit. 2-What is the power value measured in the short circuit test of this transformer? -The value of iron losses of this transformer what?
Illustrate a single phase transformer and describe how it works? -why is voltage stepped up for transmitting? -why is voltage steeped down for domestic use?
In the Open-circuit test of the transformer (OC TEST), wattmeter measures 2 kW, in the short-circuit test of the transformer (SC TEST) wattmeter measures 200kW. Find the core loss of the transformer?
A 20 kVA, single phase-phase, 50 Hz, 2200/200 V transformer gave the following test results: O.C. test: 2200 V, applied to primary; power input 220 W S.C test: powersequired to dirculate full-load current in short-orcuited secondary 240 W. Find the efficiency at full-load and half full-load at power factor of 0.8 lagging.?
1. A single-phase step-down transformer is rated at 10 kVA, 208V/120 V. a. Compute the rated current of each winding. b. If a 2 Ω load resistance is connected across the 120 V winding, what are the currents in the high-voltage and low-voltage windings? c. What is the equivalent load resistance referred to the 208 V side? d. What is the lowest load resistance that is allowed by the transformer rating?
A 10-kVA, 200-V/400-V, 50-Hz, single-phase transformer gave the following test results : OC test (HV winding open) : 200 V, 1.3 A, 120 W. SC test (LV winding shorted) : 22 V, 30 A, 200 W. Calculate (a) the magnetizing current, and (b) the equivalent resistance and leakage reactance as referred to the low voltage side.