Q1: A: A steam generator operates at 15 bar absolute pressure. The economizer receives the water at 35°C and heats it to 104°C while the super heater receives steam and heats it to 300°C. The coal used as a fuel has a heating value of 33.5MJ/kg and the steam produced per kg coal is 10kg/kgf. Determine the E.E and boiler efficiency?
Q: Vector A has a magnitude of 6 units and it is in the direction of positive X-axis vector B has a…
A:
Q: 9. Steam is contained in a 4-liter volume at a pressure of 1.5 MPa and a temperature of 200°C. If…
A:
Q: The following figure shows an epicyclic gear train (EGT) having two inputs. The sun gear 2 rotates…
A:
Q: When fluid flows through a pipe with varying diameter, the greater velocity is in the…
A: Correct answer: smaller
Q: Describe the four processes, which occur in the vapor-compression-refrigeration cycle that you…
A: Compressor, condenser, expansion valve/throttle valve, and evaporator are the four components of…
Q: All collars slide freely. A = 5.0 ft/s downward at the instant shown. Using ICR, determine @AB and…
A:
Q: Five kilogram of steam is initially at 1MPa and y=40% inside the piston cylinder. There is a 50C…
A: Given:m=5 kgP1=1 MPax=0.4
Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…
A: 7. In planning, the tool travels along the workpiece during the removal of the material on the…
Q: 4. Calculate the total turbine work of the cycle. a. 1,936.2 kJ/kg b. 1,293.6 kJ/kg c. 1,629.3 kJ/kg…
A: Given: →h1=3348.4 KJ/Kg ; →h2=2963.5 KJ/Kg→h3=hf+xhfg@0.7MPa=697.22+0.9895×2066.3=2741.82…
Q: Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given…
A: Draw the P-V diagram of the a cold air-standard Diesel cycle.
Q: A force F = 250 N is applied to a two-bar truss as shown and 0 = 36 degree. Determine the value of…
A: Given: F = 250 N and truss of two members Answer: F1 = 136.44 N
Q: What is the speed of the connector pin at B if the angular velocity of the bar AB is 8 rad/s…
A:
Q: Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 27 °C, with a…
A:
Q: The spherical pressure vessel has an inner diameter of 2 m and a thickness of 10 mm. A strain gauge…
A: Given: d = 2m deformation = .014 mm t = 10 mm l = 20 mm
Q: 15. To solve Lt sint you may use: nl L (s = a)+¹ 16. Le cos(5t)} = IL (-1)^{t(t)}
A: 15. Given: The function, F(t) = L(t^3sint)
Q: The 45° strain rosette is mounted on the surface of a shell. The following readings are obtained for…
A:
Q: Two uniform spheres are positioned as shown. Determine the gravitational force F which the titanium…
A:
Q: The request for this project is to design the diameter of the output shaft of a single reduction…
A: Please find the solution below
Q: The following figure shows an epicyclic gear train (EGT) having two inputs. The sun gear 2 rotates…
A: Write the expression for the angular velocity of gear 3. ω3=ωarm-T2T3ω2
Q: An open tank containing water is accelerated vertically at 5.8 If the motion is downward with…
A: Given Density = 1000 kg/m3 Depth, h = 1.85 m Find Pressure, P
Q: Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 27 °C, with a…
A:
Q: High pressure turbine blades experience the most hostile combination of conditions of any component…
A: A high-pressure turbine is used to extract the work efficiently. In a high-pressure turbine, a set…
Q: Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator…
A:
Q: . Spring is hung vertically, and an object of mass (m) is attached to its lower end. The spring…
A:
Q: 18-67. The system consists of a 30-kg disk, 12-kg slender rod BA, and a 5-kg smooth collar A. If the…
A: Given data as per the question Mass of disk =30 kg Mass of the collar =5 kg considering the given…
Q: 17-78. Two cylinders A and B, having a weight of 10 lb and 5 lb, respectively, are attached to the…
A: Given Mass, mA = 10 lb mB = 5 lb Time, t = 5 sec Find Speed, v
Q: A1 m long and 35 mm diameter aluminum shaft is to be replaced by a steel hollow shaft of the same…
A: When torque is applied on the shaft, then only shear stresses are produced which acts in two…
Q: A Particle undergoes simple harmonic motion with a freque e displacement X at any time (t) for the…
A:
Q: Example 5-1 on EGT The following figure shows an epicyclic gear train (EGT) having two inputs. The…
A:
Q: At 3MPa and 400C, 2 kg/s steam flows into a turbine. It exits at 300kPa. The turbine has an…
A: Given: P1 = 3 MPa = 3000 kPa P2 = 300 kPa T1 = 400 C efficiency = 85% Ideal case means isentropic…
Q: The following figure shows an epicyclic gear train (EGT) having two inputs. The sun gear 2 rotates…
A:
Q: Example 2: Water is going to be pumped between point A and B as shown in Figure below. Calculate the…
A:
Q: (c) Consider the following steady, three-dimensional velocity field in Cartesian coordinates. V =…
A: The condition for the flow field to be incompressible: a = 24•c3
Q: The mass of the concrete block shown in the figure is 5 kg and the spring stiffness is 25 kN/m. A…
A: Given data: m=5 kgmo=0.15 kgk=25 kN/mvbi=500 m/svbf=-80 m/s Need to determine the resulting motion…
Q: Question (2): The ball B of mass= 0.25 kg is blown through the smooth vertical circular tube whose…
A: Given: The mass of ball, m = 0.25 kg The radial position of the ball, r = 0.7sinθ The angular…
Q: Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given…
A:
Q: 18-38. The spool has a mass of 50 kg and a radius of gyration of ko = 0.280 m. If the 20-kg block A…
A: Given Mass, M = 50 kg m = 20kg Angular velocity = 5 rad/s Find…
Q: A flat plate has been placed longitudinally in a stream of crude oil which flows with a velocity of…
A: Length of the plate, L=500 mm=0.5 mWidth of the plate, w=250 mm=0.25 mVelocity of crude oil, U=6…
Q: Q1) Draw the sheering force and bending moment diagrams for fig1 2kN 20KN 10kN 1m 1m 1m FBD 10kN…
A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…
Q: Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator…
A:
Q: Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given…
A: GIVEN DATA- A DIESEL CYCLE GIVEN p1 = 100 kPa, T1 = 340 K, and T3 = 4850.3 K, Compression ratio r…
Q: two dimensional conservation force is zero on the X and Y Axes and satisfied condition (dfx/dy)=…
A:
Q: Find the shear stress about the neutral axis if V = 2000K.
A:
Q: B. Evaluate each of the following and express with SI units having an appropriate prefix.…
A: 1) (50mN)(6GN) 1 mN = 0.001 N 1 GN = 1 x 109 N (50mN)(6GN) = (50 x 0.001 N) (6 x 109 N) = 300 x 106…
Q: The distributed load is supported by a box beam as shown below. Determine the maximum value of wo…
A:
Q: Given the three vectors A = i, B = i- j, and C = k Find A.(BXC).
A:
Q: Two beads are sliding freely on a horizontal rod. Use the following conditions. MA - 3 kg ma - 1 kg…
A:
Q: The diagram below represents the wet-bulb and dry-bulb temperatur on a sling psychrometer. What was…
A:
Q: 2.Steam enters an adiabatic turbine at 3MPa and 500C and exits at 30 kPa. If the efficiency of the…
A:
Q: The 18-lb object is travelling at a speed of 8 ft/s when the force of 15 lb is applied in the same…
A:
Step by step
Solved in 2 steps with 2 images
- A typical temperature relationship between a high-efficiency condenser and the ambient temperature is A. 10F. B. 20F. C. 30F. D. 40F.The influence of maximum temperature on the efficiency of a Rankine cycleis desired. Holding the maximum and minimum pressures constant at 1000psia and 2 psia, respectively, what is the thermal efficiency if the boiler outletsteam temperature is (a)8000F, (b)10000F, and (c)12000F?Data for steady-state operation of a vapor-compression refrigeration cycle with Refrigerant 134a as theworking fluid are given in the table below. State 1 is at the compressor inlet. The cooling capacity (i.e therate at which heat is removed from the cooled space) is 4.6 tons. 1 ton of refrigeration is equivalent to211 kJ/min. Ignoring heat transfer between the compressor and its surroundings, sketch the ?-? diagramof the cycle and determinea) the mass flow rate of the refrigerant, in kg/min.b) the isentropic compressor efficiency.c) the coefficient of performance.State ? (bar) ? (°C) ℎ (kJ/kg) ? (kJ/kg-K)
- A refrigerator operating using vapor-compression cycle uses R-134a as a working fluid. The condenser temperature is 65oC and the evaporator temperature is -15oC. The compressor operates at 80% efficiency. a. Determine the coefficient of performance of the refrigeration cycle. b. How much refrigerant is needed to deliver 3 kW of cooling? c. Sketch the vapor compression cycle indicating the states of each stream (in terms of H, P, T, and S) and showing the values of energy input/output in the system d. Suppose that we replace the expansion valve in the vapor- compression cycle with a turbine that operates at 80% efficiency. Determine the coefficient of performance of the refrigeration cycle. Provide the new state properties (i.e. H, P, T and S) for this changes Please use CATT for any values neededA simple ideal Rankine cycle which uses water as the working fluid operates its condenser at 40C and its boiler at 300C. The steam enters the turbine without any superheating. Determine the Wp (kJ/kg).(Use 2 decimal places for the final answer.)A steam cycle operates between 150 bar, 1000 K, and 1 bar. Theturbine and feedpump are perfectly efficient, and, two open feedwaterheaters being used, the splits in the streams through the turbine into theheaters are optimal. Determine(a) The fraction of the total flow that must pass through eachfeedwater heater,(b) The thermal efficiency.Draw T-s and Schematic Diagram.
- complete solutions with four decimal digits. Box the final answers, Write legibly. Consider a 210 MW steam power plant that operates on a simple ideal Rankine cycle, steamenters the turbine at 10 MPa and 500 °C and is cooled in the condenser at a pressure of 10kPa. Determine the following:a. Mass of steam in kg/secb. Turbine power in kWc. Power of the pump in kWd. Heat added to the cyclee. Heat rejected by the cyclef. Rankine cycle efficiencyA steam power plant operates between the pressure limit of 3.0 Mpa for the boiler and 40 kPa for the condenser. If the plant operates in an ideal Rankine cycle with superheated vapor enters the turbine at 3 Mpa and 500 oC, determine:a) the moisture content at the inlet of the condenser,b) the net work per unit mass of steam flowing, in kJ/kg,c) the heat transfer to the steam in the boiler in kJ per kg of steam,d) the thermal efficiency,e) the heat transfer to cooling water passing through the condenser, in kJ per kg of steam flowing. h1 (kJ/kg) Format : 227.25 v1 (m3/kg) Format : 0.002092 h2 (kJ/kg) Format : 320.445 h3 (kJ/kg) Format : 8765.2 s3 (m3/kg) Format : 4.7267 x4 Format : 0.959 h4 (kJ/kg) Format : 7845.82 W (kJ/kg) Format : 555.79 Qin (kJ/kg) Format : 6362.75 Efficiency (%) Format : 50.83Solve neatly and draw diagrams. write neatly An regenerative engine receives 68,000 kg/hr of steam having 1 open heater which receives 15,400 kg/h of Bled steam. If the condenser pressure is 0.008 MPa and the open heater pressure is 0.98 MPa find the enthalpy a) at the heater entrance, b) condenser entrance.
- J 5 A Carnot refrigeration cycle is used to maintain a room at 23 °C by removing heat from groundwater at 15 °C. Refrigerant R-134a enters the condenser as saturated vapor at 40 °C and leaves as saturated liquid at the same temperature. The evaporator pressure is 351 kPa. a) If the room is to receive 2kW, what is power input to the compressor? b) Net power input to cycle?1st Step: Evaluate the performance of the Refrigerator 1.Refrigerator 1 operates as a reverse Carnot cycle using R-717 as the refrigerant at aflow of 1.8 kg/s. The condensing and evaporating temperatures are 25 °C and -5 °C, respectively.To evaluate the performance of Chiller 1, you must determine the following performance parameters:project:a) Rate of heat elimination in the condenser (Q );b) The power of the compressor;c) The COP of the cycle.For the energy balance, make the following considerations:- Permanent regime;- Variation of kinetic energy and potentials are negligible;- Compressor and turbine operate adiabatically;- Evaporation and condensation steps do not involve work. Please, make it typeable, written in virtual text, do not do it by hand and do not take a photo, it interferes with the understanding of the lyrics.A simple vapor - compression cycle develops 13 tons ofrefrigeration. Using ammonia as refrigerant and operating at acondensing temperature of 24 °C and evaporating temperature of-18°C and assuming that the compression are isentropic and thatthe gas leaving the condenser is saturated. Find the followinga). Draw the p-h diagramb.) Refrigerating effect in kJ/kgc.) Circulation flow in kg/mind.) Power requiremente.) Volume flow in cubic meter per minute per tonf.) Coefficient of performanceg.) Power per ton