Q1) A full-wave rectifier uses two diodes. The transformer r.m.s. secondary voltage from the center tap to each end of the secondary is 70 V and load resistance is 1000 2. Find: a) The mean load voltage and current b) The r.m.s. value of load current c) The PIV of the diode d) The efficiency of rectification

Q1) A full-wave rectifier uses two diodes. The transformer r.m.s. secondary voltage from the center tap to each end of the secondary is 70 V and load resistance is 1000 2. Find: a) The mean load voltage and current b) The r.m.s. value of load current c) The PIV of the diode d) The efficiency of rectification

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
A full-wave bridge rectifier with a 236.86V p-p sinusoidal input has a load resister of2KΩi. Draw the wave form that the load resistor R would see. ii. Assuming diodes are ideal, what is the dc voltage available at the load resistor? iii. What is the dc voltage available at the load if silicon diodes are employed? iv. Calculate the maximum current flow through the Diode D4 during conduction.
Find the peak output voltage for the bridge rectifier. Also, assuming ideal diodes, find the PIV rating required for the diodes. The transformer is specified to have 12 Vrms secondary voltage for the standard 110 V across the primary.(Show complete solution)
Design Half-wave Rectifier Circuit to provide an output of 100 VDC. Then calculate its transformer peak voltage rating, the diode PIV rating, and the transformer turns ratio, if the power is taken from the 220V line AC supply
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
(a)Derive the average and rms output voltages and currents for three-phase half controlled rectifier with free wheeling diode and RLE load.(b))In a single phase full converter, if output voltage has peak and average values of 325V and 133V respectively, find the firing angle.
The full-wave rectiﬁer ias shown is operating at a frequency of 60 Hz, and the rms value of the transformer output voltage is 18 V. (a) What is the value of the dc output voltage if the diode voltage drop is 1 V? (b) What is the minimum value of C required to maintain the ripple voltage to less than 0.25 V if R = 0.5 Ω? (c) What is the PIV rating of the diode in this circuit? (d) What is the surge current when power is ﬁrst applied? (e) What is the amplitude of the repetitive current in the diode?
A full-wave bridge rectifier with a 12V (pk) sinusoidal input has a load resistor of 20 k. (a) If silicon diodes are employed, what is the dc voltage available at the load? (b) Determine the required PIV rating of each diode. (c) Find the maximum current through each diode during conduction. (d) What is the required power rating of each diode?
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
The power in the rectifier circuit given by Vs = 220 sen(??)V and the four diodes with an ideal behavior R = 1kΩ. Explain the behavior of the converter during the negative semi-cycle of the tension Vs. To analyse the behavior, explain which way the electric current should circulate, what is the tension in the load and the diodes, what is the duration of the semi-cycle, and what is the value of the electric current in the load and the diodes.
Figure shows an AC source G having an effective voltage of 240 V, 60 Hz is connected to a single-phase full-wave rectifier. The resistance for R is 53 Ω and ripple-to-ripple current is 15%.Determine the DC voltage and DC current across the resistor. Hence, determine the power absorbed by the load. Assuming all diodes are ideal.
) Determine the reading obtained withaDC voltmeter at RB when the switch is set at point B. b) Determine the reading at thesame RBusing ½ wave and Full wave rectifier AC meter respectively when the switch is set at point A. Given that Ifs = 100-µA and set at 10-V dc or rms range.