Worksheet 2_3_2021Q1: Construct a higher MUX using smaller one:5 to 32 decoder using (3 to 8 or 2 to 4 MUX or combination of both)Q2: implement an 8 to 1 Mux using onlyi. Two 4 to 1 and one 2 to I MUXii. Four 2 to I and one 4 to 1 MUXQ3: Realize the function F (A, B, C) =m, + m2 + m, + m; usinga. 8 to 1 MUXb. 4 to 1 MUXQ4: A: Design a 16 to I Demultiplexer using 4 to I multiplexer only.B: The serial data input waveform and data selectors are shown below, determinethe data-output waveform for the I to 4 demultiplexer.Data inputC: Determine the output waveform in relation to the input for 4 to 1 Multiplexer.DoD.D2D3SoPage 1 of 1

As per the guidelines, we supposed to answer one question at a time so please ask other questions…

Answered: Q1: Construct a higher MUX using…

Engineering

Electrical Engineering

Q1: Construct a higher MUX using smaller one: 5 to 32 decoder using (3 to 8 or 2 to 4 MUX or combination of both)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please check the formula logic and the formula for my solution for answer a Alo please check the formula and calculation for the part b. I got confused about the conversionts and not sure if i did it all correct way. a) The transmission time of a frame can be calculated as follows: Propagation delay (Tp) = distance/speed = 5km / 200000 km/s = 0.025ms Transmission time (Tt) = frame size/bandwidth = 10000 * 8bits / (1Mbps * 10 ^ 6) = 0.008sec = 8ms Total time for transmission = 2 * Tp + Tt(since the frame has to travel from A to D and then D to A) = 2 * 0.0025ms + 8ms = 0.005ms + 8ms = 8.005ms The transmission time of the frame from A to D is 8.005 ms. b) To calculate the efficiency of the CSMA/CD protocol in this LAN, we can use the formula: Efficiency = (1 / (1 + 5tprop / tframe)) tprop is the propagation delay tframe is the time it takes to transmit a frame. To calculate tprop, we need to determine the time it takes for a signal to propagate through the 5 Km distance…
Create and build a 7 segment decoder circuit using the truth table and Kmap method. Required are as follows. 1. Truth table2. Seven Segment of each number 0 to 93. KMAP of each Letter A to G4. Equation of each Letter A to G5. Individual OR Compiled Circuit A to G
It's up to you: Do you think error correction is more effective when used with wireless applications? People will believe what you say if you give them examples to back up your claims.
Is Thevenin’s theorem likely to be widely used in practice? Why? **please type it using keybord NOT hand writing**
Solve correctly please. Need all subparts for ratings
Asynchronous counter that repeats 0, 1, 8, 9, 12, 13 counting sequences circuit by using negative (falling) edge triggered TFFs. design. a)with truth table b)Karnaugh maps simplification c)circuit drawing
Figure 2 Bit error graph (image insterted) The numbers on the right of Figure 2 are multipliers. For example, working upwards from the horizontal line representing 10–10, the next horizontal line up represents 2 × 10–10; the next line up represents 4 × 10–10, and so on. The next line up from 8 × 10–10 has no number on the right and represents 10 × 10–10, which is 10–9, as shown on the vertical axis on the left. In mobile cellular communications, the signal-to-noise ratio is often poor, particularly indoors. Suppose that at an indoor location the signal-to-noise ratio is 7 dB. What would the corresponding bit-error probability be? A rule-of-thumb in mobile communications engineering is that the signal-to-noise ratio indoors is 10 dB worse than outdoors at the same location. Using this rule-of-thumb, what would the bit-error probability be outdoors at the same location as in (a)? By what factor has the signal-to-noise ratio improved by moving from indoors to outdoors? Express…
b) Figure 3.1 is an attempt made to implement the circuit in part a) using a 3-to-8 decoder. i) Complete a Truth Table for the circuit in Figure 3.1 ii) Identify the error(s) in the circuit in Figure 3.1. With the aid of a circuit diagram, explain how you would modify the circuit in Figure 3.1 so that it would perform the same function as part a).
Please use python code 6. Use the adaptive Runge-Kutta method to integrate y' =(9/y -y)x with y(0) =5 from x =0 to 4 and plot y vs x.
Question ACTIVITY : CODING Suppose the following messages are source encoded given by the table. Message Encoded Bits UP 00 DOWN 01 LEFT 10 RIGHT 11 Complete the given table by writing the source encoded message of the following set of directions. Set of Directions Source Encoding LEFT - UP - RIGHT - DOWN 1.) UP - DOWN - UP - RIGHT 2.) DOWN - DOWN - RIGHT - LEFT 3.) UP - DOWN - LEFT - RIGHT 4.) RIGHT - LEFT - RIGHT - UP 5.) Decode the set of directions given by the message received. Message Received Decoded Message 10010011 1.) 01010010 2.) 11000110 3.) 01100111 4.) 00101111 5.) III. Complete the given table by writing the channel encoded message by using parity check of adding 1 bit in the message. Message Source Encoding Channel Encoding ALLY 000 1.) ENEMY 011 2.) ATTACK 100 3.) RETREAT 111 4.) SURRENDER…
Comment on the values of intemediary circuit elements that are calculated during your work: are these elements possible to build in the real world?
Use a 4-to-1 multiplexer and a minimum number of external gates to realize the function F(w,x,y,z) = Σm(3,4,5,7,10,14) +Σd(1,6,15). The inputs are only available uncomplemented.