Q1) Determine the size of the rivets to be used for the joint of the bracket shown in Figure (1). All rivets are to be of the same size. Rivet spacing C is 30 mm; plate thickness is 25 mm; permissible shear stress is 200 MPa and permissible crushing stress is 400 MPa. boutoud +++ 300 mm 10 KN

Q1) Determine the size of the rivets to be used for the joint of the bracket shown in Figure (1). All rivets are to be of the same size. Rivet spacing C is 30 mm; plate thickness is 25 mm; permissible shear stress is 200 MPa and permissible crushing stress is 400 MPa. boutoud +++ 300 mm 10 KN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.10P: A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a...

See similar textbooks

Related questions

Q: 3. An oil of kinematic viscosity 0.25 stokes flows through a pipe of diameter 10 cm. The flow is…

A: Kinematic viscosity v=0.25 stokesDiameter d=10 cm=0.10 mTo Find-The velocity for critical flow.

Q: If the mass of cylinder is 100 kg, find the tension developed in wires AB and AC and find the…

A: Consider the support point O as origin. Thus, the cooridnates of points are, , , and .Write…

Q: Q-7: This question have two different approaches. Solve for both. (a) Determine the resultant couple…

Q: Weightless bar AD is suspended by cable BE and supports a block that ontacts between the bar ends…

A: The free-body diagram for the system is,Note-As the walls are frictionless, thus all the weight is…

Q: 250 kg/h of air saturated at 2°C is mixed with 50 kg/h of air at 35°C and 80% relative humidity.…

Q: a) Determine the coordinates of the centroid? b) Determine the moment of inertia about the…

Q: For the instant represented, when crank OA passes the horizontal position. Crank OA has a uniform…

A: The schematic diagram is as follows,The angle between link AB and horizontal,

Q: V 3) Some top-flight tennis players hit the ball on service at the instant see ball is at the top of…

Q: For the frame and loadings shown P=2240 KN, and F=1120 magnitude of horizontal reaction at C…

A: P=2240 KN, and F=1120Findmagnitude of horizontal reaction at Cmagnitude of horizontal reaction at A

Q: A vented tanker is to be filled with fuel oil with p = 920 kg/m³ and u= 0.045 kg/m-s from an…

A: Given DataThe density of the oil is: The viscosity is: Length of the pipe is: Diameter of the pipe…

Q: The assembly consists of a 3-\rm kg pulley A and 11-\rm kg pulley B. Neglect the mass of the cord…

Q: 4. The pressure in a stationary liquid depends on the position below the surface z according to p(2)…

Q: A maritime research vessel may not use more than 65% of its 8000kW power plant when cruising at…

A: To find:the maximum volume of the sonar unit that may be pulled along the vessel while adhering to…

Q: Q3/A/ a steel slab is upset forged from: (50mm×200mm×100mm) to (25mm × 200mm × 200mm). If the…

Q: Example 2. A cylindrical bar of 40 mm diameter and 1 m length is subjected to a tensile test. Its…

A: A cylindrical bar-Diameter d=40 mmLength L=1 mLongitudinal strain is 6 times lateral strainModulus…

Q: B- Estimate the necessary area for a tank used to settling sand particles had an average diameter of…

Q: The figure shows a part of a machine used to crush recycled cans. Link ABC is attached to the ground…

Q: 1. A diverging pipe has diameter of 20cm and 30cm respectively at section 1 and section 2. If the…

Q: The 58-kg cylinder is suspended from a clamping collar at C which can be positioned at any…

A: Given DataW=58kg Here we give free body diagram

Q: Q4 / A thick cylinder of (200mm) external diameter and (100mm) internal dian internal pressure of…

Q: can explain D,E,F more clearly also

A: d ) The force required for circular motion is the centripetal force, which is provided by the lift:…

Q: B. A compound generator delivers 140 A at 300 V and the resistance of the shunt field, series…

A: To calculate the electromotive force (EMF) of the compound generator, you can use the same formula…

Q: 3. The disk starts from rest and is given an angular acceleration a = (5t¹/2) rad/s², where t is in…

Q: 2.16 A velocity field is given by V = ayti-bxj, where a = 1 s-² and b=4s ¹. Find the equation of the…

A: The velocity field is The values are

Q: Q- fluids, The Coefficient of discharge of a orifice meter is 0.97. The time taken by fluid to cover…

A: The coefficient of discharge of the orifice meter Cd = 0.97The time taken by fluid to cover 8 cm of…

Q: Q- mechanics, A fan consumes 50 W of electric power and has an air discharge of 0.25 kg/s, find the…

A: Power consumed P= 50 W Air discharge m = 0.25 kg/sTo Find-The maximum air outlet velocity (v).

Q: A circular shock absorber, as shown in the figure below, is designed to support a set of sensitive…

A: Force applied (F): 1000 NDiameter of aluminum circular bar (d1): 4 mmDiameter of hollow circular…

Q: A single edge-cracked plate of AISI 4130 Steel of Table 8.1 has dimensions, as defined in Fig…

Q: Determine the force P required to force the 14° wedge under the 70-kg uniform crate which rests…

A: Draw the free-body diagram for the block system.The angle phi is,

Q: A laminated beam is composed of three planks, each 150mm by 60mm, glued together to form a section…

Q: Q1/ A two circular bars of brass (AB) and steel (CD) in horizontal state with gap of (1.5min)…

Q: A 15 mm diameter steel bar was bent as shown. Using the work and energy method, determine the…

Q: The landing gear of an aircraft can be modelled as a spring-mass-damper system as illustrated in the…

A: Given:

Q: As shown in the figures below, and the Video, a rectangular barge floats in a stable configuration…

A: Draw the given table.And,

Q: The frame for a sign is fabricated from a thin, flat steel bar stock of mass per unit length 4.73…

Q: For the beam and loading shown, determine (a) the reaction at point C, (b) the deflection at point…

Q: Saturated liquid water at 35[bar] undergoes an ideal throttling process to 10[bar]. The quality of…

A: According to the given dataP1=30 barP2=10 barProcess 1 to 2 is a throttling process.We need to…

Q: One of your friends is riding a mechanical bull outside of the grocery store. The mechanism…

Q: A 600-MWe power plant has an efficiency of 36 % with 15% of the waste heat being released to the…

A: The objective is to determine the rate makeup water be provided from the river to offset the water…

Q: dista the load slides. 2. Using the radii of the double pulley, determine how high John will rise…

A: John's weight, Load weight, Large double pulley weight, The outer radius of the double pulley, The…

Q: wraps radiu 0.8 ft, and weighs 10 lbs. Drum B has radius rs = 2 ft, radius of gyra 20 lbs. I stand…

Q: a) Calculate the shear force and bending moment for the beam subjected to a concentrated load as…

Q: A commercial refrigerator is to cool eggplants from 26 to 5 °C at a rate of 380 kg/h. The power…

A: As there are multiple sub parts, according to our guidelines we are supposed to answer the first…

Q: 4) Arm AB has a constant angular velocity of 16 rad/s counterclockwise. At the instant when = 60°,…

A: To be determinedAcceleration of D and G

Q: 25.18 The following is an initial-value, second-order differential equation: dx ²+(5x) + (x +7) sin…

A: To decompose the given second-order differential equation into a system of first-order differential…

Q: A rigid block of mass M is mounted on four elastic supports, as shown in the figure below. A small…

A: Mass of the rigid block (M): M=55kgMass of the small dropped mass (m): m=6kgSpring constant of each…

Q: blank are installed in supply-water piping to prevent water hammer. Bypass valves, air chambers,…

A: Which of the following is installed in supply water piping to prevent water hammer.Water…

Q: Q1/Replace the force and couple system acting on the member in Figure below by an equivalent…

A: The force couple system is the summation of all forces and moments at a point that produces the same…

Q: D L I The water in a large tank ovite through horizontal circuler

Q: 4. For two-point loading bending test of a beam shown in Fig. 3, the maximum moment was found…

A: Draw free body diagram of the beam.At equilibrium, i) equate algebraic sum of moment of forces about…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Q1) Determine the size of the rivets to be used for the joint of the bracket shown in Figure (1). All rivets
are to be of the same size. Rivet spacing C is 30 mm; plate thickness is 25 mm; permissible shear stress is
200 MPa and permissible crushing stress is 400 MPa.
kukood
+ +
+
ACICH
300
mm
Figure (1)
10 KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Write the given data with suitable variables.

VIEW

Step 2: Determine the value of centroid and size of the rivets.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two boards are joined by gluing along a scarf joint, as shown in the figure. For purposes of cutting and gluing, the angle a between the plane of the joint and the faces of the boards must be between 10° and 40f. Under a tensile load P, the normal stress in the boards is 4.9 MPa. (a) What axe the normal and shear stresses acting on the glued joint if a = 20°? (b) If the allowable shear stress on the joint is 2.25 MPa. what is the largest permissible value of the angle ct? (c) For what angle a with the shear stress on the glued joint be numerically equal to twice the normal stress on the joint?
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A tension member is to be constructed of two pieces or plastic glued along plane pq (see figure). For purposes of cutting and gluing, the angle ?? must be between 25 and 45. The allowable stresses on the glued joint in tension and shear are 5.0 MPa and 3.0 MPa, respectively (a) Determine the angle it so that the bar will carry the largest load P. (Assume that the strength of the slued joint controls the design.) (b) Determine the maximum allowable load ?? if the cross-sectional area of the bar is 225
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.