Q1: Draw the orthographic Projections of given object. 15 R20

Q: nd the angle between along diagonal and an adjacent face diagonal of a cube..

A:

Q: = Draw the orthographic Projections of given object. 15 R20 00

A:

Q: Draw the orthographic Projections of given object.

A: Solution: The Top, front and Side views are shown below:

Q: Q1: Draw the orthographic Projections of given object.

A: Orthographic Projection

Q: the value of X

A:

Q: Draw the orthographic Projections of given object. $30 080

A: The orthographic projections of the object include Top View, Front View, and Side View. All…

Q: Q/FIND THE MISSING LOCATION

A:

Q: H.W/ For the the figure shown, draw the front view, top view, and side view.

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Give all the location dimensions between the datum target areas, A1 and A2. Y=- Give all the…

A:

Q: Determine the isometric or 3D view of the given orthographic drawing

A: Given Orthographic views To find  Isometric view

Q: The distance between two stations A and B is 100 kilometers and its equivalent distance on the…

A: Distance between two stations A and B, actual length = 100 km Equivalent distance on map, length…

Q: Draw the orthographic Projections of given object. 15 R20 00

A:

Q: Projective Geometry: Draw two of same object, one near and one far. The objects at the back should…

A:

Q: QI: Draw the orthographic Projections of given object.

A: Orthographic projection is a means of representing three-dimensional objects in two dimensions. It…

Q: Orthographic projection of the component show below

A:

Q: 70 R25 R15 R5 R10 R5 R10 100

A: Given CAD model To find Orthographic view

Q: 02 2N Find markdore.

A: Given data : The value of force applied F=2 N The value of Distance moved by an ball d=1.1   To find…

Q: Q1: Draw the orthographic Projections of given object. 15

A: Solution:   The orthographic projections of the given object is shown below:

Q: Q1) Create an orthographic projection of the following object. Draw the three standard views. Y.

A:

Q: Draw the hologram

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: The distance between two stations A and B is 100 kilometers and its equivalent distance on the…

A: Given dataDistance between two stations D = 100KmLenght on the drawing sheet = 2.5cmMaximum length L…

Q: Convert the decimal number 35710 into its binary number equivalent

A: Steps Divide the number by 2. Get the integer quotient for the next iteration. Get the remainder…

Q: me numerical values corresponding to bc

A: introduction: here we give the solution of two mcq

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: . Convert the decimal number 35710 into its binary number equivalent.

A: Given: A decimal number is, (357)10 .

Q: Q2: Draw the orthographic Projections of given object. 30 80

A: The orthographic projection with 1st angle projection is shown in the step below.

Q: Q/DRAW THE PROJECTIONS OF A SHAPE

A: According to the details provided in the question, we need to calculate projections of the object.

Q: Draw the orthographic Projections of given object. 50 as 10 20 60 25 50 15

A: To make an orthographic projection of the given object,  Place the object in 1st quadrant,

Q: in seconds, construct s-t, v-t, and a-t graphs for 0

A: given:s=2sinπ5t+4

Q: Q2:- Draw the sectional front view of the object given below. [15] $70 $50 08

A: The front view is the view observed in x-direction. Sectional front of the object will be given as:

Q: Given the Isometric views, draw the three orthographic views below

A: Orthographic views of the given isometric view are drawn on the grid paper. 1 Grid = 1 unit.

Q: В 60 cm 8 70 cm 10 rad's 6 rad/s? 80 cm Figure Q5

A:

Q: P2-13) Sketch the front, top and right side views of the following object. Use the grid provided.

A:

Q: 13. If we use plus and minus signs to indicate the directions of velocity and acceleration, then the…

A: Given:Positive acceleration means the velocity of the object is increasing.Negative acceleration…

Q: se Write Legibly. Box the final answer.

A: P1=10MPaT1=600CP2=0.2MPa To-Find:- a) Work,steam rate, thermal efficiency and mean effective…

Q: 2. The orthographic view shows the part from Sides. Select one: a.4 O b.2 c.3 d.1

A: Orthographic views are two dimensional views of a three dimensional object.  They are usually…

Q: Need you to draw orthographic views of this object.

A: The required orthographic views are drawn using third angle method of projection.

Q: 2. Draw the auxiliary view of the orthographic views above.

A:

Q: GIVEN THE ORTHOGRAPHIC VIEWS, CREATE AN ISOMETRIC SKETCH OF THE FOLLOWING OBJECT.

A: Isometric projection is a method of representing three-dimensional objects into two dimensions…

Q: 1. Complete the 3rd angle projection, i.e., draw the TOP view orthographic.

A: Data given - Enginnering drawing  To obtain - 3rd angle projection or top view orthographic

Q: Q1: Draw the orthographic Projections of a given object

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: A small bracket is shown in plan and elevation. Draw in First Angle projection the given views and…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Q1) Create an orthographic projection of the following object. Draw the three standard views-

A:

Q: a)Draw the multiviews (Front, Top and Left) of the part given below. b) Show the dimensions of the…

A: According to the details provided in the question, we need to draw three standard View

Q: us esecale (2-2) to draw the orthographic projections (top view, front view, side) for the…

A: Find Draw the orthographic projections of the given object by using a scale (2.2).

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.