Q1: For the beams and loading shown below, A-Draw the shear force and bending-moment diagrams. . B- Determine the equations ofthe shear force and bending-moment curves for the segments (BC in Figure 1, C-Compute the bending stress at point (a) on section C`., D-Determine the values and locations of the maximum tensile and compression bending stresses.

Q1: For the beams and loading shown below, A-Draw the shear force and bending-moment diagrams. . B- Determine the equations ofthe shear force and bending-moment curves for the segments (BC in Figure 1, C-Compute the bending stress at point (a) on section C`., D-Determine the values and locations of the maximum tensile and compression bending stresses.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.10.17P

See similar textbooks

Similar questions

A wood box beam is constructed of two 260 mm × 50 mm boards and two 260 mm × 25 mm boards (sec figure). The boards are nailed at a longitudinal spacing. b = 100 mm. If each nail has an allowable shear force F = 1200 N. what is the maximum allowable shear force Vmax?
A two-axle carriage that is part of an over head traveling crane in a testing laboratory moves slowly across a simple beam AB (sec figure). The load transmitted to the beam from the front axle is 2200 lb and from the rear axle is 3800 lb. The weight of the beam itself may be disregarded. Determine the minimum required section modulus S for the beam if the allowable bending stress is 17,0 ksi, the length of the beam is 18 ft, and the wheelbase of the carriage is 5 ft. Select the most economical I-beam (S shape) from Table F-2(a), Appendix F.
Derive the formula for the bending stress of a beam with a rectangular cross section and triangular cross secrion. Thank you
A gantry crane of weight W=100 Kg moves across a bridge with the length I=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles.
Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft
For the beam and its shear diagram shown below, the distance x is measured from the left end of the beam. The maximum moment occurs where x is ?
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 0.63 in from the bottom of the beam on a section 1.68 feet to the right of B if P = 2290 lb, Q = 8457 lb, w = 1.37 in, L = 8 in, b = 3.7 in, and h = 1.12 in. Round off the final answer to two decimal places.
FInd the Magnitude of the Maximum Shear Stress in the below beam and cross-section, if: w = 17 kN/m L = 8 m b = 85 mm h = 178 mm Ensure that your answers are in MPa.
Draw the shear and Bending moment diagram of each beam below using the equation method and area method. CHANGE 20 kN/m to 33 kN/m
Calculate the maximum normal bending stress and the maximum shear stress
Determine the normal force, shear force, and bending moment BY USING THE LEFT SIDE at C ofthe beam in Fig. 7–5a.
Determine internal shear force, internal bending moment and internal normal force at point c