Q1) Implement AND gate with three inputs. F=A.B.C To complete the circuit, take a screen shot (or use snipping tool), paste it into your software of choice and crop it accordingly. In multisim Q2) Implement OR gate with four inputs. F=A+B+C+D. To complete the circuit, take a screen shot (or use snipping tool), paste it into your software of choice and crop it accordingly. Q3) Find the function of the following circuits ? y -

Q1) Implement AND gate with three inputs. F=A.B.C To complete the circuit, take a screen shot (or use snipping tool), paste it into your software of choice and crop it accordingly. In multisim Q2) Implement OR gate with four inputs. F=A+B+C+D. To complete the circuit, take a screen shot (or use snipping tool), paste it into your software of choice and crop it accordingly. Q3) Find the function of the following circuits ? y -

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter33: Single-phase Motors

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

1. Circuit Topology (Show solution) a. Simplify the circuit below such that there is only one voltage source and one equivalent resistor Rs in the circuit. Do not use source transformation. What is Rs? b. Simplify the circuit below such that there is only one current source I1 and one equivalent resistor Rp in the circuit. Do not use source transformation. What is Rp?
im new to the concept of nodal analysis so when finding vab u applied nodal analysis to get v1 but on what basis did you put the values in the numerator and denominator? and what part of the circuit did you not take into account while calculating it? since there seem to be some missing values. i mean what does each number refer to. also when calculating vth and used v1 to find it how did u get x2/2+1? i know about the voltage division rule but im a bit confused can you please elaborate on all these points?
5) Obtain a implementation of a half-adder circuit using standard gates such as AND, OR, NOT, XOR, etc. Obtain the minimal standard sum-of-products expressions for the Carry and Sum outputs of a half-adder. Compare these expressions with your implementation. PS:Please answer Number 6 after from number 5 6) Draw the schematic diagram of your implementation of the half adder from step 5).
Q2) Design a combinational circuit which take 4bit input and it has 7 outputs to which connect with the 7-segment common cathode. Your circuit has to display any one of the following alphabet on 7-segment. 1010= A 1011= b 1100= C 1101= d 1110= E 1111= F Attach the truth table & K-map with proteus screen shot showing result. From the above choice choose any one alphabet to display.
R1=560Ω, R2=1000Ω, R3=470Ω, R4=2200Ω, R5=1000Ω V1 =12V and V2 = 5V Calculate every current in the given circuit by using the superposition principle. ( IR1C=?, IR2C=?, IR3C=?, IR4C=?, and IR5C=?)
30 For the circuit attached:Give the AND-OR expression as it is shown (No Spaces in your expression w'y+yz' not w'y + yz') (List from the top AND gate to the bottom AND gate)Draw a K-Map for it (Do not attach the K-Map) Give the minimum AND-OR expression for it
One can assemble a “virtual” solar cell array by using playing cards, or business or index cards, to represent a solar cell. Combinations of these cards in series and/or parallel can model the required array output. a) Assume each card has an output of 0.5 V and a current (under bright light) of 2 A. Using your cards, how would you arrange them to produce an output of 6 A at 3 V (i.e. - 18 W)? b) Suppose you were told that you needed only 18 W (but no required voltage). Would you need more cards to make this arrangement?
Q1.Please design a FSM to implement the basic function of onevending machine.a. You can insert two types of coins (1 yuan or 2 yuan)b. This machine can deliver one bottle of water worth 2 yuanGive the whole process of your solution: identification of input,output, state, stategraph, statetable, NextStateEquation, output equation and diagram of the circuit. Note (I have already answered it but i am not sure if its correct so can you write it in orderly manner ?)
"MILLMAN’S THEOREM " Please Find the Current and Voltages in 6k , 3k , 6k Ohm Resistors only, with a total of 3 currents and 3 voltages to compute Using NMILLMAN’S THEOREM thankyou very much ! I've included a cicruit app to check if your answer was correct and close to the value of currents and voltages thankyou! I've been testing simple circuits to practice problems using different theorems,I appreciate you very much Thankyou!
Q3: Design Adder circuit to add two numbers each has 3 bits .How many * ?gates do we use in the solution
Please solve briefly i) Describe the steps to determine the mesh currents in Mesh Analysis. ii) Explain the principle of ‘source transformation iii) Explain TWO (2) disadvantages of using circuit simulator in electronic circuits
For the circuit in the figure, draw the equivalent circuit and values I1, I2 and ID1, ID2.find? need handwritten only ,otherwise downvote.)