Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg) and supports load (200 kg) at (A). Determine the tension (T) in the cable and reaction force at (B)? Bi 2-5m 2.5m A 200 kg 2.5 m

Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg) and supports load (200 kg) at (A). Determine the tension (T) in the cable and reaction force at (B)? Bi 2-5m 2.5m A 200 kg 2.5 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.125P: The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A...

See similar textbooks

Related questions

Q: The beam shown has an overall length L of 6.9 metres. A uniform distributed load of 3.9 kN/m is…

A: GIVEN DATA- A CANTILEVER BEAM GIVEN SUBJECTED TO UDL FOR A LENGTH WE HAVE TO FIND MOMENT ABOUT A

Q: How many degrees of lom are required to model the systems shown in Identify a set of generalized…

Q: A jet of water issues from 100 mm diameter nozzle with a velocity of 20 m/s. Find the HP of the jet.…

A: Given, Velocity of jet and diameter of nozzle Find Horse power developed by jet

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

Q: The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the…

Q: The steel shaft with two different diameters rotates at 4.4 Hz. The power supplied to gear C is 73…

A: find the maximum shear stress in the shaft.

Q: Determine the forces in members BC and CG. The forces are positive if in tension, negative if in…

Q: Determine the average normal stress and average shear stress at point C in the beam. The…

Q: Calculate the polar moment of inertia of the shaded area about point O. y 57 mm 26 mm Answer: I - i…

Q: please use this steam table

Q: Calculate the moment of inertia of the shaded area about the x-axis. 93 mm 93 mm 51 mm Answer:I,-i…

A: Square length, a= 93 mm Quarter circle radius, r= 51 mm Note:

Q: The variable h designates the arbitrary vertical location of the center of the circular cutout…

Q: 10. Ice accumulation on an evaporator can be quickly pressure to open and close a larger valve is 9.…

A: Given questions are related to refrigeration and fluid flow control:…

Q: Q3/ For the figure shown below, .compute the centroid of the figure 6m 3m 4.5 m 3m

A: find the centroid of the shaded area.

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

Q: 13) Which of the following is NOT process control? A: Temperature control B: Lighting on/off control…

A: In process control, process variable (such as temperature, pressure etc.) is measured (using…

Q: A ball is thrown from the top of a tower 30 m above the ground with velocity of 30 m/s directed at…

Q: Determine the forces in members DE and DL. The forces are positive if in tension, negative if in…

Q: applied. Use k1 - 12.67 N/m, k2 - 11.1 N/m, k3 - 28.39 N/m, and k5 - 33.91 N/m. (Use 2 decimal…

Q: Task 2 The transfer of heat from one fluid to another is an essential component of all chemical…

A: Introduction: Heat exchanger: The heat exchanger is a device that is widely used to transfer heat…

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. Assume F = 770 N, a =…

A: F= 770 Na= 635 mmb= 290 mmθ= 26∘ϕ= 65∘

Q: A cascade refrigeration system serves a 75 ton evaporator at 119.4 KPa. The system uses direct…

Q: A drive shaft running at 2500 rpm has outer diameter of 80mm and inner diameter of 60mm. The…

Q: 2. The satellite dish below tracks the movement of an airplane traveling on a straight line above…

Q: 1. If oil with specific gravity of 0.80 is used to measure the atmospheric pressure, how high would…

A: 1) If oil with specific gravity of 0.80 is used to measure the atmospheric pressure, how high would…

Q: For the steel truss and loading shown, determine the deformation (in inches) of member BD, knowing…

A: Using method of sections to calculate force in member BD

Q: e. A steam Carnot engine operates between 350°C and 120°C. The net power output is 450 kW. Calculate…

A: INTRODUCTION : Two temperature limitations are presented in this problem; we treat one as higher…

Q: The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress…

A: First consider the rigidity criterion. The angle of twist in the solid shaft can be expressed as…

Q: Consider a mass spring system with an external force F(t) = F, sin w,t. Let's assume m is the mass…

Q: Combined Rankine Cycle Show the details of your solutions with Schematic and TS diagrams…

Q: operate on Brayton cycle with a pressure ratio of 8, the maximum and minimum temperature of the…

A: Solution is attached below

Q: Determine the height h above the base of the centroid of the cross-sectional area of the beam.…

Q: A heat engine is operating on a Carnot cycle and has a thermal efficiency of 55 percent. The waste…

A: Heat Engine is a device which converts heat into some useful work and rejects the wasted heat into…

Q: uses air and operates between temperature limits of 7400F and 400F. The pressure at state 1 is 200…

Q: Calculate the moment of inertia of the shaded area about the x-axis.

Q: The following properties for Freon-12 were obtained. At -22 °C h (superheat) = 353 KJ/kg ha = 343…

Q: Determine the largest load P that can be applied at A when 0 = 50° , knowing that the allowable…

A: Pin diameter, dpin= 10 mm Thickness of the member AB, t= 16 mm Thickness of the bracket at B. tb= 12…

Q: Adjusting rear camber is the first step in the four-wheel alignment process. What are the components…

A: given; adjusting rear camber is the first step in the four wheel alignment process. what are the…

Q: Which of the following components is NOT within the refrigeration cycle? A: Expansion valve B:…

A: To find : Which of the following components is NOT within the refrigeration cycle?

Q: Q3/ For the figure shown below, .compute the centroid of the figure 6m 3m 4.5 m

Q: a device that allows hot refrigerant vapor from the compressor discharge line to bypass the…

A: In cold weather, the hot gases from the compressor are most likely to drop their pressure below the…

Q: 1. As shown in the figure, what is the static gage pressure in kg/cm² in the air chamber? Air 1.5 m…

A: find the static pressure in the air chamber.

Q: The 21-kg uniform thin hollow square plate is pinned at point O, and its side L = 0.5 m. If it is…

A: Given Givenm=21kgL=0.5mM=78Nmθ=45o=π4

Q: A Carnot engine operating between temperature limits of 10000F and 5000F produces 80,000 ft-lbf of…

A: Given Tmax = 10000 F Tmin = 5000 F W = 80, 000 ft lbf To find Heat rejected Thermal efficiency

Q: A 2-kg object moving to the right at 3 m/s collides head-on with a 4-kg object moving to the left at…

Q: Is there anyway you can write the equations doesn't make sense with equations typed like that

Q: which of the following statements regarding relief valves is not true? A. A blown fusible plug must…

A: Which of the following statements regarding relief valves is not true? Answer: D. Spring-loaded…

Q: A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 267 mm in…

Q: A uniform rod AB of mass m = 6.4kg is welded at its midpoint G to a vertical Shaft GD. Knowing that…

A: Component of w along xdash axis, W'=wcos(20°)=5.7*Cos(20°)=5.36rad/s

Q: Calculate the x- and y-coordinates of the centroid of the shaded area. 19"

A: To determine the centroid of the given composite area.

Question

Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a
mass of (50 kg) and supports load (200 kg) at (A). Determine the tension (T) in
the cable and reaction force at (B)?
Bi
2-5m
2.5m
A
200 kg
2.5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
A bar AE is in equilibrium under the action of the five forces shown in Figure. Determine T, P, and R.
Determine the tensions T1 and T2 in the strings required to maintain equilibrium for the suspended object weighs W = 48.7N shown in the figure. Take, α = 29.4° & β = 47.5°. a) The value of θ1 (Degree) = b) The value of θ2 (Degree) = c) The value of θ3 (Degree) = d) The value of Tension, T1 (N) = e) The value of Tension, T2 (N) =
Determine the tensions T1 and T2 in the strings required to maintain equilibrium for the suspended object weighs W = 48.7N shown in the figure. Take, α = 29.4° & β = 47.5°. a) The value of Tension, T1 (N) = b) The value of Tension, T2 (N) =
Determine the tensions T1 and T2 in the strings required to maintain equilibrium for the suspended object weighs W = 38.7N shown in the figure. Take, α = 29.8° & β = 50.2°. The value of Tension, T1 (N) = The value of Tension, T2 (N) =
A bar AB of weight 180kN is hinged at A and held at equilibrium by a force P as shown in the figure. Determine the magnitude of force P about the hinge reaction at A for the equilibrium position of the bar AB. Take the length of the bar as 10m.
1) The thin plate shown in the figure below weighing 99 kg/m^2, is lifted slowly by the cables AC and BC. For equilibrium, determine the distance x in m 2) Determine the tension in the cable AC in N. 3) Determine the tension in the cable BC in N
Two cylinders having 75 kg and 20 kg mass are connected with a cable and held in equilibrium on smooth surfaces as shown in the figure. Determine the contact forces between the cylinders and the surfaces, the tension in the cable and the angle θ
The boom AC in the figure rests in a ball and socket joint at A and is held in equilibrium by the cables BE and CD. The load applied at C. Determine the coordinates of D in the YZ plane so that the force in CD will be a minimum. Neglect the weight of the boom and cables. Answers: y = 16ft ; z = -34.7ft ( Please i need the solution)
The structure shown in the figure carries a 5000 kg platform. Considering that the structure has also singular forces at joints C and D:a) Determine the reactions at the supports, b) Also determine the forces in members AB, AC, AD, and BD. State whether each member is in tension or compression. Note 1: Take the gravitational acceleration as 10 m/s2.Note 2: Assume that all connections between members are pin joints.
The cylinder C in the figure below weighs 1000lbs. Determine the tension in the cable , and the reactions A and F