I need the answer as soon as possible Q1: Parabolic cables of the roadbed of a suspension bridge are positioned as shownbelow. Vertical Cables are to be spaced every 6 m along this portion of the roadbed.Calculate the lengths of first two of these vertical cables from the vertex. usey=a(x-h)+K equation and round (a) value to four decimal places and the height ofcables to two decimal places.2m18

Answered: Image /qna-images/answer/782e3179-9ed0-4520-95de-afa54441b072.jpg

Q1: Parabolic cables of the roadbed of a suspension bridge are positioned as shown below, Vertical Cables are to be spaced every 6 m along this portion of the roadbed. y-a(x-h)+K equation and round (a) value to four decimal places and the height of Calculate the lengths of first two of these vertical cables from the vertex. use cables to two decimal places. 2m 18 722

Q1: Parabolic cables of the roadbed of a suspension bridge are positioned as shown below, Vertical Cables are to be spaced every 6 m along this portion of the roadbed. y-a(x-h)+K equation and round (a) value to four decimal places and the height of Calculate the lengths of first two of these vertical cables from the vertex. use cables to two decimal places. 2m 18 722

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

determine the slope at point B in radian. The equation of elastic curve are the following: E = 200 GPa, I = 1660 x 10^6 mm^4 Let w = 118kN/m, L = 13m
A 50-m steel tape was used to measure a line and the initial pull = 5.5 kg. Pull at time of measurement = 8.0 kg. Weight of tape = 0.05 kg/m. E = 2.1 x 10^6 kg/cm^2? Cross section = 0.04 sq.cm. Measured distance between two points =488.650 m, in an inclined surface having a gradient of 3%. Find the correct horizontal distance between the two points. A. 486.456 C. 488.625 B. 490.844 D. 488.147 The distance from A to B taken at elevation 1200 m above sea level is 6,750 m. Determine the sea-level distance. A.6748.734 C. 6749.347 B. 6751.266 D.6750.274 ps. with solution, please.
calculate the vertical displacement on both sides of point C which is a roller guide using conjugate beam method. E = 29,000 ksi, I = 200 in^4
Determine the slope and displacement at the end A of the beam. Take E=29(10^3) Ksi, I=170in^2. Use the method of virtual work
Determine the slope at A in radian. Using Moment Area Method. Let P =38 kN. EI = 14220 kNm^2 Round off the final answer to three decimal places.
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15 If there is a settlement of S at the support C, solve the following using slope deflection method: 1. Slope at B, in radians
(a) Compute the vertical deflection and slope of the cantilever beam at points B and C in Figure P8.20. Given: EI is constant throughout, L = 12 ft, and E = 4000 kips/in.2 . What is the minimum required value of I if the deflection of point C is not to exceed 0.4 in.?
Find the distance x (measured along AB) at which a horizontal force of P=8- lb should be applied to hold the uniform bar AB in the position shown in the figure. Bar AB is 10 ft long and weighs 140 lb. The incline and the floor are smooth.
Kindly solve the slope and deflection at each point using Area Moment Method (show solutions and diagrams) some answers:θC = 0.465°ΔC = 40.52 mm
Compute for the value of P that required to cause the system of blocks to have impending motion to the right.
The blocks shown are separated by a solid strut which is attached to the blocks with frictionless pins. If the coefficient of friction for all surfaces is 0.25, determine the value of the horizontal force P to cause motion to impend to the right.
If F1 = 100 N, F2 = 120 N, and F3 = 80 N, determine the magnitude and coordinate direction angles of the resultant couple moment.