Q1/ The aluminum and bronze cylinders are centered and secured between two rigid end-plates by tightening the two steel bolts. There is no axial load in the assembly at a temperature of 50°F. Find the stress in the steel bolts when the temperature is increased to 200°F. Use the following data: Aluminum cylinder Bronze cylinder Each steel bolt A (in.2) 2.00 3.00 0.75 a (/°F) 12.8 x 10-6 10.5 x 10-6 6.5 x 10-6 E (psi) 10 x 106 12 × 106 29 x 106 1.0 in. 3 in 4 in. 1.0 in. Aluminum Bronze

Q1/ The aluminum and bronze cylinders are centered and secured between two rigid end-plates by tightening the two steel bolts. There is no axial load in the assembly at a temperature of 50°F. Find the stress in the steel bolts when the temperature is increased to 200°F. Use the following data: Aluminum cylinder Bronze cylinder Each steel bolt A (in.2) 2.00 3.00 0.75 a (/°F) 12.8 x 10-6 10.5 x 10-6 6.5 x 10-6 E (psi) 10 x 106 12 × 106 29 x 106 1.0 in. 3 in 4 in. 1.0 in. Aluminum Bronze

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Similar questions

mechanics of deformable bodies The cylindrical tank has an outer radius of 1.5m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal stress.
A smooth-walled 100 mm edge steel bucket is filled with rubber to form a rubber bucket embedded within the steel bucket. If the rubber hub is compressed by a 100 kN force, determine: a) The normal contact stress between the rubber and the inner walls of the steel. b) The change in volume experienced by the rubber bucket. Consider the following: - The steel bucket is rigid. - There is no friction between the smooth walls of the steel bucket and the rubber (shear stress equal to zero between steel and rubber). - Rubber properties: E = 4 MPa and v = 0.45.
The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. The thickness r,-r; is small compared to r; (a) Determine the axial force F in the ring in terms of p, w and r;. Hint: Consider a FBD by cutting the ring+membrane in two. (b) Determine the hoop stress in the ring. (c) Determine the hoop strain in the ring. The modulus of elasticity for the ring is E. (d) Relate the hoop strain to the change in the inner radius of the ring after this pressure is applied, and use this to get the change in the inner radius in terms of p, E, w, r, and ri- (PLEASE ANSWER ASAP AND CORRECTLY)!
The cylindrical tank with a spherical end cap has an outer radius of 2 m and a wall thickness of 50 mm. If the tank is pressurized to 3.5 MPa, determine the longitudinal and circumferential stresses in the cylinder, and the stress in the end cap. (Show free body diagram and complete solution)
The forces applied to pulleys are given as shown below. Accordingly, show the stress state at point A on a 2-dimensional stress element and find the Von-Misses equivalent stress.
1) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and it's length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa and the circumferential stress is limited to 60 MPa 2) A compound thin cylinder has a common diameter of 100 mm, and the inner cylinder has a thickness of 2,5 mm. The radial pressure between the two cylinders is 200 KPa and the difference between the two common diameters before shrinkage was 0,004305 mm. E=200 GPa Determine : A) Thickness of the outer cylinder B) Resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 KPa
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
The cylinder is shown in Figure is made of steel having a specific weightof gst = 490 lb>ft3. Determine the average compressive stress acting atpoints A and B.
A thick-walled cylinder has an outer and inner diameter of 200 and 50 mm, respectively. The cylinder is designed to store fluid at 80 MPa:(a) Determine the external pressure necessary to bring the hoop stress at the outer wall of the cylinder to zero. (b) Draw the variations of the hoop and radial stress across the thickness of the wall. Indicate the stress values at both inner and outer radii.
Air pressure in the cylinder is increased by exerting forces P = 3 kN on the two pistons, each having a radius of 45 mm. The cylinder is shown in the figure below. If the cylinder has a wall thickness of 2 Mm, determine the circumferential stress in the wall of the cylinder. Express your answer to three significant figures and include appropriate units.
• When the state of stress is represented by the principal stresses, no shear stress will act on the element. True or False?
For the given system;a) Draw internal force diagrams and determine the most critical section.b) Show the stress distribution on this critical section and find the maximum normal stress.GIVEN: ℓ1 = 80 cm, ℓ2 = 40 cm, M = 8000 Ncm, b = 4 cm, h = 6 cm, t = 1 cm, F = 1400 N, qo = 30 N/cm .