Q1: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P, = 400 kN and P2 = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ARE = 11,100 mm² and Acr = 9,280 mm?. The distances between various points on the bars are shown in the figure. Determine the vertical displacements d, and op of points A and D, respectively. 15 m 1.5 m- 2.1m- BO D P = 400 kN 2.4 m P2 = 360 kN F

Q1: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P, = 400 kN and P2 = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ARE = 11,100 mm² and Acr = 9,280 mm?. The distances between various points on the bars are shown in the figure. Determine the vertical displacements d, and op of points A and D, respectively. 15 m 1.5 m- 2.1m- BO D P = 400 kN 2.4 m P2 = 360 kN F

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever beam 5 m long carries a concentrated load P at 3.75 m from the fixed end. ( E = 25 x 103 MPa, I = 1.6 x 109 mm4, P = 150 KN) What is the deflection under the load P? What is the maximum beam deflection? What is the upward force applied at the free end to prevent the beam from deflecting?
Calculate the vertical reaction at support A. Enter your answer in kN to two decimal places.
A simply supported beam L meters long carries a uniformly distributed load of 16 kN/m over its entire length and has a T cross-section. The flange is 140mm x 20 mm place and the web is 160 mm by 20 mm. 1. Which of the following most nearly gives the moment of inertia about N. A.? a. 10.25 x 10⁶ mm⁴ b. 17.23 x 10⁶ mm⁴ c. 22.24 x 10⁶ mm⁴ d. 19.02 x 10⁶ mm⁴ 2. Which of the following most nearly gives the value of L to cause a maximum flexural strength of 40 MPa? a. 1.77 m b. 2.82 m c. 3.24 m d. 4.00 m 3. Which of the following most nearly gives the maximum horizontal shearing stress developed? a. 24 MPa b. 38 MPa c. 45 MPa d. 32 MPa
Solve for: 1. Maximum W in kN if each leg resist 10.098 kN. 2. If W is 49 kN. what is the force resisting of leg DA? 3. If W is 51 kN. what is the force resisting of leg BA?
Calculate the vertical shear stress (N / cm2) at point A in the critical section of the beam below whose load and section is given? The cross section is symmetrical with respect to the y-axis. (Point A is on the body, point B is on the x-axis and point C is on the header.) (Q = 6000 N / m, P = 60000 N, L = 3 m, b = 50 cm t = 5 cm, h = 20 cm) please fast help please
What is the Vertical component (y-component) reaction force at support C? A. 600N, ( + ) upward B. 200N, (+) upward C. 600N,(-) downward D. 200N,( - ) downward SHOW SOLUTIONS
Calculate the member force on member HF in Kips? Specify if T or C. 87.6 C 105.9 C 79.7 C 97.5 C 112.1 C
A continuous beam ABC has fixed supports. Constant value of El and using slope deflection method. What is the moment MAB in KN-m? 2 decimal places
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
The main beam of UB 610 x 229 x 101 kg/m in steel grade S275 supportssecondary beamsof UB 406 x 140 x 39 kg/mon its top flange.The schematic diagram of the floor supported by the beams is presented in Figure 1. b)The slab floor is reinforced concrete 150 mm thickwith 50 mm screed on top of it. The slab floor carriesthe uniform distributed load of 400 kg/m2.Calculate the ULS load on the secondary beam. 4xxx= 4715 1xxx= 1715 50xx= 5015
Calculate the plastic moment in KN-m of an A36 steel beam with plastic section modulus of 401,816mm3. Express your answer in 2 decimal places.
A block with mass m=(24+12)kg is pulled by a horizontal force P applied at point B in Fig.3. The coefficient of kinetic friction between the surfaces is we = (5A+5)/(25+94). When the acceleration of the block is a=(1+9)/4 m/s?, determine the cable forces Tax and Top- 0=(A+8) A=1